NISSAN X-TRAIL 2001 Service Repair Manual

DOOR
BL-9
C
D
E
F
G
H
J
K
L
MA
B
BL
Removal and InstallationEIS000KK
NOTE:
●During door assembly removal and installation, use a jack to support the door. Place cloths or something
similar on the jack plate to protect the door and body from damage.
●After door assembly removal and installation, always adjust it so will open and close smoothly.
●Confirm the rotating part of the hinge has adequate lubrication. If necessary, apply Body Grease.
1. Remove door finisher. Refer to EI-23, "
DOOR FINISHER" .
2. Remove sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
3. Remove door harness.
4. Remove check link mount bolts on the body.
5. Remove hinge mount nuts on the door and then the door
assembly.
Install in the reverse order of removal.
SIIA0145E
SIIA0146E

BL-10
DOOR
Door Weatherstrip
EIS000KL
SIIA0157E

POWER DOOR LOCK SYSTEM
BL-11
C
D
E
F
G
H
J
K
L
MA
B
BL
POWER DOOR LOCK SYSTEMPFP:24814
System DescriptionEIS001SE
OPERATION
Power door lock/unlock operation by door key cylinder
●With the key inserted into driver's door key cylinder, turning it to LOCK will lock all doors.
●With the key inserted into driver's door key cylinder, turning it to UNLOCK will unlock all doors.
Power door lock/unlock operation by lock/unlock switch
●With lock/unlock switch setting to LOCK will lock all doors.
●With lock/unlock switch setting to UNLOCK will unlock all doors.
Key reminder system
●If the ignition key is in the ignition key cylinder and driver door is open, setting lock/unlock switch, lock
knob, key or multi-remote controller to “LOCK” locks the door once but then immediately unlocks all doors.
(signal from door unlock sensor driver side)
Component Parts and Harness Connector LocationEIS004DC
PIIA0584E

BL-12
POWER DOOR LOCK SYSTEM
Schematic
EIS004DD
TIWA0003E

POWER DOOR LOCK SYSTEM
BL-13
C
D
E
F
G
H
J
K
L
MA
B
BL
Wiring Diagram — D/LOCK —EIS004DE
TIWA0004E
SMA for models with roof 
mounted driving lamp

BL-14
POWER DOOR LOCK SYSTEM
TIWA0005E

POWER DOOR LOCK SYSTEM
BL-15
C
D
E
F
G
H
J
K
L
MA
B
BL
TIWA0006E

BL-16
POWER DOOR LOCK SYSTEM
TIWA0007E

POWER DOOR LOCK SYSTEM
BL-17
C
D
E
F
G
H
J
K
L
MA
B
BL
Terminal and Reference Value for Time Control UnitEIS000KP
Termi-
nalWire
ColorItem ConditionVo l ta g e
(Approximate values)
1 L/B BAT power supply — 12V
4 G/RPassenger door and rear door
(LH/RH) lock actuator unlockDoor lock/unlock switch
(Free → Unlock)0V → 12V
10 W Power source (C/B) — 12V
11 L Driver door lock actuator unlockDoor lock/unlock switch
(Free → lock)0V → 12V
14 R/B All door lock actuator lockDoor lock/unlock switch
Unlock operation0V → 12V
16 B Ground — 0V
17 G IGN power supply — 12V
18 W/L Key switchKey inserted (ON) → key removed
from IGN key cylinder (OFF)12V → 0V
20 GYDoor lock/unlock switch lock sig-
nalLock operation (ON) 0V
Other than above (OFF) 5V
23 PUDoor lock/unlock switch unlock
signalUnlock operation (ON) 0V
Other than above (OFF) 5V
24 LG/R Door key cylinder lock switch OFF (Neutral) → ON (Locked) 5V → 0V
25 OR/L Door key cylinder unlock switch OFF (Neutral) → ON (Unlocked) 5V → 0V
28 Y/G Driver door lock switch signalUnlock (ON) 0V
Lock (OFF) 5V
30 R Driver door switch Door open (ON) → close (OFF) 0V →12V

BL-18
POWER DOOR LOCK SYSTEM
Symptom Chart
EIS001R5
*:Make sure the power door lock system operates properly.
Power Supply and Ground Circuit CheckEIS004DF
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect time control unit connector.
3. Check voltage between time control unit and ground.
OK or NG
OK >> GO TO 2
NG >> Check the following.
●Harness for open or short between time control unit and fuse
●Harness for open or short between circuit breaker
Symptom Malfunctioning systemReference
page
Power door lock does not operate using any switchPower supply and ground circuit checkBL-18
Front door lock actuator check (Driver side)BL-21
Front door lock actuator check (Passenger side)BL-22
Rear door lock actuator check LH BL-23
Rear door lock actuator check RHBL-24
Back door lock actuator checkBL-25
If above systems are OK, replace time control unit. —
Power door lock does not operate with lock/unlock
switch.Door lock/unlock switch checkBL-19
If above system is OK, replace time control unit. —
Power door lock does not operate with door key cylinder
switch.Door key cylinder switch checkBL-20
If above system is OK, replace time control unit. —
Specific door lock actuator does not operate.Front door lock actuator check (Driver side)BL-21
Front door lock actuator check (Passenger side)BL-22
Rear door lock actuator LHBL-23
Rear door lock actuator RHBL-24
Back door lock actuatorBL-25
If above system is OK, replace time control unit. —
*Key reminder system does not operate.Door switch checkBL-26
Door unlock sensor checkBL-26
Key switch checkBL-27
If above system is OK, replace time control unit. —
Terminal Ignition switch position
+ – OFF ACC ON
1
GroundBattery
voltageBattery
voltageBattery
voltage
10Battery
voltageBattery
voltageBattery
voltage
PIIA3645E