torque RENAULT KANGOO 1997 KC / 1.G Engine And Peripherals Workshop Manual

ENGINE AND ENGINE PERIPHERALS
Engine - Gearbox
10
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the electrical connectors from the engine
connection unit and its environment.
13034S
Drain:
- the cooling circuit (bottom hose of the
radiator),
- the gearbox oil,
- the engine oil if necessary.
Remove:
- the battery,
- the bonnet,
- the wheels,
- the air intake pipe,
- the expansion bottle and fix it to the engine. Brake caliper guide bolt 4
Shock absorber base bolts 18
Driveshaft gaiter mounting bolt 2.5
Wheel bolt 9
Left-hand suspended mounting bolt
on gearbox 6.2
Left-hand suspended mounting bolt
and nut on body 2.1
Right hand suspended
engine mounting bolt on engine 6.2
Right hand suspended
engine mounting bolt on body 6.2
TIGHTENING TORQUES (in daN.m)
D7F engine
SPECIAL TOOLING REQUIRED
B. Vi. 31-01 Set of three punches for roll
pins
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1311-06 Tool for removal of fuel pipe
Mot. 1379 Tool for retaining engine on
sub-frame
T. Av. 476 Ball joint extractor
EQUIPMENT REQUIRED
Load positioner
10-4

ENGINE AND ENGINE PERIPHERALS
Engine - Gearbox
10
12924R3
Apply Rhodorseal 5661 to the driveshaft roll pin hole.
Press the brake pedal several times to bring the pistons into contact with the brake pads.
Refit the power assisted steering pump belt (see section 07).
Fill:
- the gearbox with oil,
- the engine with oil (if necessary),
- the cooling circuit and bleed it (see section 19).
REFITTING (special notes)
Refitting is the reverse of removal.
Tighten the suspended engine mounting bolts to the recommended torque.
NOTE : tighten the suspended engine mounting bolts on the body in the order recommended below:
-1⇒bolt A to a torque of 2.1 daNm.
-2⇒bolt B to a torque of 2.1 daNm.
-3⇒bolt C to a torque of 2.1 daNm. D7F engine
10-8

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the electrical connectors from the engine
connection unit and its environment.
13034S
Drain:
- the cooling circuit (disconnect the bottom
hose of the radiator),
- the gearbox oil if necessary,
- the engine oil if necessary.
Remove:
- the battery,
- the wheels,
- the air intake pipe,
- the upper radiator mountings,
- the expansion bottle and fix it to the engine,
- the power assisted steering fluid reservoir,
and secure it onto the engine. Shock absorber base bolts 18
Track rod end 3.7
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Driveshaft gaiter mounting bolt 2.5
Wheel bolt 9
Mounting nut for rubber engine mounting
pad on left suspended engine mounting 6.2
Mounting bolt for front right suspended
engine mounting on the engine 6.2
Mounting bolt for front right suspended
engine mounting on the body 6.2
Steering shaft yoke bolt 2.5
TIGHTENING TORQUES (in daN.m)
D7F engine
SPECIAL TOOLING REQUIRED
B. Vi. 31-01 Set of punches for roll pins
Mot. 1040-01 Dummy sub-frame for
removing and refitting engine
and transmission assembly
Mot. 1202 Hose clip pliers
Mot. 1311-06 Tool for removal of fuel pipe
Mot. 1379 Tool for retaining engine on
sub-frame
T. Av. 476 Ball joint extractor
T. Av. 1233-01 Tool for sub-frame and axle
assembly
10-9

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
12924R4
Apply Rhodorseal 5661 to the driveshaft roll pin hole.
Press the brake pedal several times to bring the pistons into contact with the brake pads.
Fill:
- the gearbox with oil (if necessary),
- the engine with oil (if necessary),
- the cooling circuit and bleed it (see section 19).
REFITTING (special notes)
Use tool T. Av. 1233-01 to position the engine and transmission assembly in relation to the body.
Refitting is the reverse of removal.
Tighten the suspended engine mounting bolts and nuts to the recommended torque.D7F engine
10-13

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Mounting bolt for front right suspended
engine mounting cover on engine 6.2
Mounting nut for front right suspended
engine mounting cover 4.4
Mounting nut for rubber engine mounting pad
on front left-hand side member support 6.2
Shock absorber base bolt 18
Brake caliper mounting bolt 4
Steering shaft yoke bolt 3
Wheel bolt 9
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain:
- the cooling circuit through the bottom hose
of the radiator,
- the gearbox and the engine if necessary.
Remove:
- the bonnet,
- the front wheels,
- the tie-rods between sub-frame and body,- the mounting bolts (1); pull away the brake
calipers as shown in the diagram below and
attach them to the suspension springs,
12994R1
- the shock absorber base bolts, E7J engine
SPECIAL TOOLING REQUIRED
Mot. 1040-01 Dummy sub-frame for removing
and refitting engine and
transmission assembly
Mot. 1159 Tool for maintaining engine on
sub-frame
Mot. 1202
Mot. 1448
Mot. 1311-06 Tool for removing fuel pipe
Hose clip pliers
10-14

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REFITTING
The alignment of the sub-frame with the body
will be made easier by positioning two threaded
rods Mot. 1233-01 in the two front mountings of
the sub-frame on the body.
Tighten the sub-frame mounting bolts to a torque
of:
- 6.2 daN.m at the front,
-10.5 daN.m at the rear.
Refitting is the reverse of removal.
Fit the heat shields correctly.
Apply
Loctite FRENBLOC to the caliper mounting
bolts and tighten them to the recommended tor-
que.
Press the brake pedal several times to bring the
pistons into contact with the brake pads.
Fill:
- the engine and gearbox with oil, if necessary,
- the cooling circuit and bleed it (see section 19
"Filling - bleeding"). E7J engine
Fix tool Mot. 1040-01 underneath the sub-frame.
98755R1
Lower the lift until the tool touches the ground.
Remove the sub-frame mounting bolts and take
out the engine and transmission assembly by lif-
ting the body.
NOTE : for any operation requiring separation of
the engine, gearbox and sub-frame assembly,
take care to mark the position of Mot. 1159 on the
sub-frame.
10-18

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
SPECIAL TOOLING REQUIRED
Mot. 1040-01 Dummy sub-frame for removing -
refitting the engine and
transmission assembly
Mot. 1159 Tool for maintaining engine on
sub-frame
Mot. 1202
Mot. 1448
Mot. 1311-06 Tool for removing fuel pipe
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Mounting bolt for front right suspended engine
mounting cover on engine 6.2
Mounting nut for front right suspended engine
mounting cover 4.4
Mounting nut for rubber engine mounting
pad on front left side member support 6.2
Shock absorber base bolt 18
Brake caliper mounting bolt 4
Steering shaft yoke bolt 3
Wheel bolt 9
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain:
- the cooling circuit through the bottom hose
of the radiator,
- the gearbox and the engine if necessary.
Remove:
- the bonnet,
- the front wheels,
- the tie-rods between sub-frame and body,- the mounting bolts (1); pull away the brake
calipers as shown in the diagram below and
attach them to the suspension springs,
12994R1
- the shock absorber base bolts, F8Q engine
Hose clip pliers
10-19

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REFITTING
The alignment of the sub-frame with the body
will be made easier by positioning two threaded
rods Mot. 1233-01 in the two front mountings of
the sub-frame on the body.
Tighten the sub-frame mounting bolts to a torque
of:
- 6.2 daN.m at the front,
-10.5 daN.m at the rear.
Refitting is the reverse of removal.
Fit the heat shields correctly.
Apply
Loctite FRENBLOC to the caliper mounting
bolts and tighten them to the recommended tor-
que.
Press the brake pedal several times to bring the
pistons into contact with the brake pads.
Fill:
- the engine and gearbox with oil, if necessary,
- the cooling circuit and bleed it (see section 19
"Filling - bleeding"). F8Q engine
Fix tool Mot. 1040-01 underneath the sub-frame.
98755R1
Lower the lift until the tool touches the ground.
Remove the sub-frame mounting bolts and take
out the engine and transmission assembly by lif-
ting the body.
NOTE : for any operation requiring separation of
the engine, gearbox and sub-frame assembly,
take care to mark the position of Mot. 1159 on the
sub-frame.
Remove the mounting bolts (3).
12993-1R3
10-24

ENGINE AND ENGINE PERIPHERALS
Sump
10
Sump mounting bolt 1
TIGHTENING TORQUES (in daN.m)
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain the engine.
Remove:
- the oil level sensor using a 19 mm half-moon
wrench,
- the engine-gearbox undertray.
99900S
Remove the sump mounting bolts.
Rotate the sump towards the rear of the vehicle in
order to release the oil pump strainer from the
sump partitioning.
Clean the sealing surfaces without scratching the
aluminium.
REFITTING
Proceed in the reverse order of removal and fit a
new gasket. D7F engine
10-25

ENGINE AND ENGINE PERIPHERALS
Sump
10
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
E7J sump bolt 1
F8Q sump bolt 1.5
Steering shaft yoke mounting bolt 3
Engine tie-bar bolt 6.2
Wheel bolt 9
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain the engine oil.
Remove:
- the front wheels,
- the nut and the eccentric bolt of the steering
shaft yoke, after pushing back the guard,
97390S1
- the lower ball joint mountings and the track
rod ends for the
E7J engine,
- the sub-frame and body tie rods,
- the gear control on the gearbox side,
- bolt (1), and slacken engine tie-bar bolt (2),
without removing it,
E7J / F8Q
engines
SPECIAL TOOLING REQUIRED
Mot. 1233-01 Threaded rods for lowering the
sub-frame
13359R1
- the bottom mountings of the bumper,
- the exhaust downpipe for the
F8Q engine.
Special notes for the E7J engine
Remove:
- the exhaust manifold heat shield,
- the catalytic converter,
- the engine flywheel guard,
- the power assisted steering pipe mountings
on the cylinder block and the multifunction
mounting.
10-26