instrument panel RENAULT KANGOO 1997 KC / 1.G Foult Finding - Injection User Guide

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 3IMMOBILISER WARNING LIGHT REMAINS PERMANENTLY ILLUMINATED
(even with ignition off) OR REMAINS PERMANENTLY EXTINGUISHED
Check that decoder unit programming has been correctly carried out.NOTES
no Replace the fuse.
yes
Check the condition of the +before ignition
fuse.
Is the fuse in good condition?
no Carry out petrol configuration G22*1*.
yes
no
Refer to the chart for bargraph 5LH in the
section "Fault finding - Interpretation of
XR25 bargraphs ".
Check that bargraph 3RH is extinguished .
Is bargraph 3RH extinguished ?
yes
no Repair the wiring.
Check continuity and insulation from earth
of the wiring between track A5 of the 18
track decoder unit connector and the
instrument panel .
Is the wiring in good condition?
Check that bargraph 5LH is extinguished .
Is Bargraph 5LH extinguished ?
yes
A
82-19

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 3
CONT
A
Carry out the following tests to determine the
faulty component :
- If the immobiliser warning light is
illuminated , disconnect the 18 track
decoder unit connector and check that
the immobiliser warning light
extinguishes,
- If the immobiliser warning light is
extinguished , connect track A5 of the
decoder unit connector to vehicle earth
and check that the immobiliser warning
light illuminates.
Does the immobiliser warning light
illuminate correctly during the test?
no Replace the instrument panel .
Replace the decoder unit .
yes
82-20

v0406.0
IMMOBILISER
Fault finding - Fault Chart (diesel version)82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 5IMMOBILISER WARNING LIGHT REMAINS PERMANENTLY ILLUMINATED (even
when ignition turned off ) OR REMAINS PERMANENTLY EXTINGUISHED
Check that decoder unit programming has been properly carried out.NOTES
no Replace the fuse.
yes
Check the condition of the +before ignition
fuse.
Is the fuse in good condition?
no Repair the wiring.
yes
Check continuity and insulation from earth
of the wiring between track A5 of the 18
track decoder unit connector and the
instrument panel .
Is the wiring in good condition?
Carry out the following tests to determine the
faulty component :
- If the immobiliser warning light is
illuminated , disconnect the 18 track
decoder unit connector and check that
the immobiliser warning light
extinguishes,
- If the immobiliser warning light is
extinguished , connect track A5 of the
decoder unit connector to a vehicle earth
and check that the immobiliser warning
light illuminates.
Does the immobiliser warning light
illuminate correctly during the test?
no Replace the instrument panel .
Replace the decoder unit .
yes
yes
Check that bargraph 5LH is extinguished .
Is bargraph 5LH extinguished ?no
Refer to the chart for bargraph 5LH in the
section "Fault finding - Interpretation of
XR25 bargraphs "
82-32

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding -Introduction
CONDITIONS FOR THE APPLICATION OF THE CHECKS DEFINED IN THIS FAULT FINDING
The checks defined in this fault finding should only be applied to a vehicle when the fault bargraph is
illuminated, indicating that the fault is present on the vehicle at the time of checking. Only a computer
fault will require replacement of the computer, whether the bargraph is permanently illuminated or
flashing .
If the fault is not present but simply memorised, the bargraph flashes and application of the checks
recommended in the fault finding section will not allow the origin of the fault to be found. In this case,
only a check of the wiring and the connection of the component in question must be carried out (it is
possible to test the wiring concerned in fault finding mode to try to obtain permanent illumination of the
bargraph ).
TOOLING REQUIRED FOR OPERATIONS ON THE AIRBAG AND SEAT BELT PRETENSIONER SYSTEMS :
- XR25 (with minimum XR25 cassette N° 16).
- XRBAG the updated N° 3 version (with the new measuring lead and its adaptors as well as the 30 track
adaptor for operations on the computer connector).
REMINDER:
When carrying out an operation on the airbag/seat belt pretensioner systems , it is essential to lock the
computer with the XR25 command G80* to avoid all risk of triggering at the wrong time (all firing lines
will be inhibited). This operating mode will be indicated by illumination of the warning light on the
instrument panel.
Never carry out any measuring operations on the airbag and pretensioners trigger lines with equipment
other than the XRBAG.
Before using a dummy ignition module, ensure that its resistance is between 1.8 and 2.5 ohms.
Only 30 track connector computers with airbag(s) function are able to be tested with the XR25.
Computers with the pretensioner function only must be checked with the XRBAG by following the checks
described in the fault finding section.
The ignition must be switched off, then on again to make the warning light extinguish following erasure
of the memory using the command G0**.
88
88-1

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 10 right hand side illuminated Fiche n° 49
Open circuit or insulation from earth on the warning light line10
Use the 30 track XRBAG adaptor to carry out operations on the computer
connector .NOTES
Warning light extinguished
after ignition
Lock the computer using command G80* on the XR25.
Check the condition of the warning light bulb.
Ensure the continuity of the connection between the warning light and track 8 of the 30 track
connector.
Ensure that 12 volts are reaching the warning light .
If the checks carried out have not proven the existence of a fault, disconnect the computer connector and
fit the 30 track XRBAG adaptor . Use the XRBAG in testing mode to check the operation of the warning
light on the instrument panel from the grey adaptor wire.
If it is possible to illuminate the warning light using the XRBAG, replace the airbag computer (consult
the section "Aid" for this operation).
If it is impossible to operate the warning light , repeat the preceding checks.
NoneNOTES Warning light illuminated
after ignition
Lock the computer using command G80* on the XR25.
Ensure the insulation from earth of the connection between the warning light and track 8 of the 30 track
connector .
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
None
Erase the computer memory using the command G0** then switch off the
ignition. Carry out another XR25 check and if there is no fault, unlock the
computer using command G81*.AFTER REPAIR
88
NOTES
88-18

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Aid
REPLACING THE AIRBAG COMPUTER
The airbag computers are sold in locked mode to avoid all risk of release at the wrong time (all
trigger lines are inhibited). This operational mode is indicated by the illumination of the warning
light on the instrument panel.
When replacing the airbag computer, follow this procedure :
- Ensure that the ignition is switched off.
- Replace the computer.
- Carry out an XR25 check.
- Unlock the computer using command G81*, only when no fault is declared.
88
88-24