RENAULT KANGOO 1997 KC / 1.G General Information Owner's Guide
Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 37
Page 31 of 37
VALUES AND SETTINGS
Brakes
07
VehicleDrum diameters or disc thicknesses (in mm)
Front
Normal Min.Rear
Normal Max. (1)Max. disc run-out
(in mm)
Front Rear
FC0X
KC0X20 17.7normal
payload
203.2
increased
payload
228.3normal
payload
204.45
increased
payload
229.50.07 -
(1) Drum: maximum wear diameter
(1) Leading brake shoe.
(2) Trailing brake shoe.
(3) Increased payload.
VehicleLining thicknesses (in mm) (including backing)
Front
Brand new MinimumRear
Brand new MinimumBrake fluid
FC0X
KC0X17.8 5.5With ABS
4.6 (1)
3.15 (2)
No ABS
4.2 (1)
2.8 (2)2
SAE J1703
DOT 4
FC0X (3)
KC0X (3)
17.8 5.5With ABS
4.8
No ABS
4.52
SAE J1703
DOT 4
07-15
Page 32 of 37
VALUES AND SETTINGS
Brake limiter
07
VehicleFuel tank
(driver on board)Test pressure (1) (in bars)
Front Rear
FC0X
KC0X
normal payload100 35.4
FC0X
KC0X
increased payload100 38
BRAKING PRESSURE
+ 8
0
90966S
+ 8
0
(1) The test is performed using two pressure gauges in an X arrangement.
07-16
Page 33 of 37
VALUES AND SETTINGS
Underbody heights
07
VehicleAt the front
H1 - H2 = ... mmAt the rear
H4 - H5 = ... mmDimension X (in mm)R-H and L-H
FC0X
KC0X73.5- 60.5 (1)
- 54.1 (2)402 (1)
430 (2)
Tolerance : ± 7.5 mm
The difference between the right-hand side and the left-hand side of the same axle of a vehicle must not ex-
ceed 5 mm, the driver’s side always being the higher.
Any adjustment of the underbody height means that the brake limiter and the headlights must be adjusted.
(1) Increased payload.
(2) Standard payload.
07-17
Page 34 of 37
VALUES AND SETTINGS
Underbody heights
07
12333R3
Dimension H5 is measured from the axis of the
suspension bar.
88636-4R
MEASUREMENT POINTS
07-18
Page 35 of 37
VALUES AND SETTINGS
Underbody heights
07
88637R
88576R
07-19
Page 36 of 37
H1 - H2 = 7 mm
H1 - H2 = 74 mm
H1 - H2 = 98 mm
H1 - H2 = 164 mm
H1 - H2 = 7 mm
H1 - H2 = 74 mm
H1 - H2 = 98 mm
H1 - H2 = 164 mm
H5 - H2 = 97 mm
H5 - H2 = 117 mm
H5 - H2 = 137 mm
H5 - H2 = 157 mm
81603S1 93011-1S
93014-1S
93013-1S
93012-1S
VALUES AND SETTINGS
Values for checking the front axle geometry
07
UNLADEN
NOT ADJUSTABLE
NOT ADJUSTABLE
NOT ADJUSTABLE
CAMBER
VALUES
CASTOR
3°55’
3°25’
2°55’
2°25’
Maximum right/left
difference = 1°
1°12’
- 0°15’
- 0°29’
- 0°13’
Maximum right/left
difference = 1°
ADJUSTMENTPOSITION OF
FRONT AXLE
KINGPIN
8°05’
10°25’
11°01’
11°56’
Maximum right/left
difference = 1°
PARALLELISM
RUBBER BUSHES
Adjustable by
rotating track
rod sleeves
1 turn= 30’
(3 mm)(For 2 wheels)
toe-out
+ 0°10’ ± 10’
+ 1 mm ± 1 mm
ANGLES
UNLADEN--
± 30’
± 30’
± 30’
07-20
Page 37 of 37
(For 2 wheels)
Toe-in
- 15’ ± 10’
- 1,5 mm ± 1 mm
- 0°50’ ± 15’
NOT ADJUSTABLE
93013-2S
93011-2S
81603S1
VALUES AND SETTINGS
Values for checking the rear axle geometry
07
UNLADEN
CAMBER
VALUES
PARALLELISM
ANGLES
UNLADENNOT ADJUSTABLE
UNLADEN--
RUBBER BUSHES
POSITION OF
REAR AXLEADJUSTMENT
07-21