RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection Workshop Manual

13B - 181
DIESEL INJECTION
Fault finding - Parameter summary table13B
V10 MR-372-J84-13B150$611.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
Tool parameter Diagnostic tool title
PR061Exterior air temperature
PR063Fuel temperature
PR064Coolant temperature
PR071Computer feed voltage
PR073Air flowmeter feed voltage
PR076Refrigerant sensor voltage
PR077EGR valve position sensor voltage
PR079Atmospheric pressure sensor voltage
PR080Rail pressure sensor voltage
PR081Inlet temperature sensor voltage
PR082Fuel pressure sensor voltage
PR084Coolant temperature sensor voltage
PR089Vehicle speed
PR125Power absorbed by the air conditioning compressor *
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR131EGR air flow variation
PR132Air flow
PR146Inlet air flow
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR157Fuel flow setpoint
PR171Air flow setpoint for EGR
PR190Engine idle speed setpoint.
PR213Rail pressure loop difference
PR358Sensor reference voltage
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR405Cylinder no. 2 fuel flow correction
PR406Cylinder no. 3 fuel flow correction
* AC: Air conditioning

13B - 182
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of parameters
PR035
ATMOSPHERIC PRESSURE
NOTESThere must be no present or stored faults.
Perform this fault finding procedure after detecting an inconsistency in the Parameters
menu of the computer or following a customer complaint (lack of power, smoke, etc.).
The atmospheric pressure sensor is incorporated in the computer, so no electrical check can be made.
The sensor default value is 750 mbar.
If this value or any other inconsistent value appears, then reset the computer.
If the computer is to be reprogrammed (see Replacement of components).
If the fault persists and remains present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR035/EDC16_V48_PR035/EDC16_V4C_PR035
MR-372-J84-13B150$658.mif

13B - 183
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PR037
REFRIGERANT PRESSURE
NOTESThere must be no present or stored faults.
Perform this fault finding procedure after an inconsistency is displayed in the
Parameters menu or after a customer complaint (no air conditioning, etc.).
Step 1
– Start the engine, switch on the air conditioning and increase the engine speed to 1,500 rpm:
– Display PR037 Refrigerant pressure in the Cold loop function on the diagnostic tool:
If the pressure is greater than ~27bar, go to step 2.
If the pressure does not rise, or remains below normal:
– Ensure that the air conditioning compressor and the relay are operating correctly.
– Check the conformity of the refrigerant pressure sensor by comparing* the value displayed by the tool (PR192)
with the reading given by the charging station high pressure gauge.
If the pressure difference = ±1.5bar, (or 1500 mbar):
Check the continuity and the absence of interference resistance on the connections between:
Injection computer, grey 24-track connector C,
track C3Track A of the refrigerant pressure sensor
Injection computer, brown 48-track connector
B, track F1Track C of the refrigerant pressure sensor
Injection computer, brown 48-track connector
B, track F3Track B of the refrigerant pressure sensor
If these connections are not faulty, replace the refrigerant pressure sensor.
If there is no difference, the refrigerant pressure sensor is correct: go to step 2.
Step 2
– Perform fault finding on the air conditioning.
*Note:
The diagnostic tool displays the absolute pressure, the charging station high pressure gauge displays the relative
pressure.
The normal difference between the two is equal to atmospheric pressure, i.e. ~1,000mbar.
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR037/EDC16_V48_PR037/EDC16_V4C_PR037

13B - 184
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PR038
RAIL PRESSURE
NOTESPerform this fault finding procedure:
– after the interpretation of fault DF053 Rail pressure regulation function,
– after an inconsistency for PR038 noted in the Parameters menu,
– after the interpretation of the fault finding procedure for AC011 Rail pressure
regulator,
– following a customer complaint (starting faults, poor performance, stalling, etc.).
Check the continuity and the absence of interference resistance on the following connections:
Injection computer, brown 48-track connector
B, track G3Track 2 of the rail pressure sensor connector
Injection computer brown 48-track
connector B, track A4Track 3 of the rail pressure sensor connector
Injection computer, brown 48-track connector
B, track C4Track 1 of the rail pressure sensor connector
If all these connections are correct, check for fuel pressure sensor power supply:
+ 5 V Track 3 of the rail pressure sensor connector
Earth Track 1 of the rail pressure sensor connector
Repair if necessary.
Check the sealing of the low and high-pressure diesel circuits (visual inspections, odour) pump housing,
overpressure valve, pipes, rail and injector unions, injector wells, etc.
If all of the previous checks are correct, switch the ignition on, wait for more than 1 minute and display PR038 Rail
pressure.
If the value is less than 50 bar, the rail pressure sensor is correct. If it is greater than this value, replace the rail
pressure sensor and tighten it to 35 ± 5 Nm.
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR038/EDC16_V48_PR038/EDC16_V4C_PR038

13B - 185
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PR059
INLET AIR TEMPERATURE
NOTESThere must be no present or stored faults.
Perform this fault finding procedure after noting an inconsistency in the Parameters
menu.
Check the air flow sensor.
Check the injection computer connections.
Repair if necessary.
Check for + 12 V on track 4 of the air flow sensor connector.
Display PR059 Inlet air temperature and check that the value displayed is not recovery value 20 °C.
If this is the case, check the coolant temperature sensor:
Injection computer brown 48-track connector B,
track G2Track 1 of the air flow sensor connector
Injection computer brown 48-track connector B,
track E2Track 2 of the air flow sensor connector
Repair if necessary.
Measure the resistance between tracks 1 and 2 of the air temperature and pressure sensor.
Replace the air temperature and pressure sensor if the resistance is not:
3,714Ω ±161Ω at 10 °C
2,448Ω ±96Ω at 20 °C
1,671Ω ±59Ω at 30 °C
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR059/EDC16_V48_PR059/EDC16_V4C_PR059

13B - 186
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PR063
FUEL TEMPERATURE
NOTESThere must be no present or stored faults.
NOTE
In the event of a relatively low outside temperature, the difference between the
fuel temperature and the engine temperature after cold starting may be greater
than 30 °C.
Check in the Fuel circuit tab in PR063 Fuel temperature that the value displayed is not the recovery value 100 °C.
If it is, check the fuel temperature sensor:
Check that the fuel temperature sensor is in good condition:
Repair if necessary.
Check the continuity and the absence of interference resistance on the following lines:
Brown 48-track connector B, track H2 Track 1 fuel temperature sensor
Grey 32-track connector C, track F1 Track 2 fuel temperature sensor
If the temperature read is inconsistent, check that the sensor follows the resistance as a function of temperature
calibration curve (NTC) correctly.
Replace the fuel pressure and temperature sensor if the resistance is not:
2,051 ± 123Ω at 25 °C
810 ± 47Ω at 50 °C
309 ± 17Ω at 80 °C
Replace the fuel temperature sensor if it is incorrect (an incorrect sensor is often the result of an electric shock).
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR063/EDC16_V48_PR063/EDC16_V4C_PR063

13B - 187
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PR064
COOLANT TEMPERATURE
NOTESNo fault should be present or stored:
Perform this fault finding procedure after noting an inconsistency in the Parameters
menu.
Display the PR064 Coolant temperature and check that the value displayed is not recovery value -30°C.
If this is the case, check the coolant temperature sensor:
Check the condition of the coolant temperature sensor connections.
Repair if necessary.
Check for the absence of interference resistance on the following lines:
Brown 48-track connector B, track F2 Track 3 coolant temperature sensor
Brown 48-track connector B, track H1 Track 2 coolant temperature sensor
If the temperature read is inconsistent, check that the sensor follows the resistance as a function of temperature
calibration curve (NTC) correctly.
Replace the air temperature and pressure sensor if the resistance is not:
2,252Ω ± 112Ω at 25 °C
811Ω ±39Ω at 50 °C
283Ω ±8Ω at 80 °C
Replace the coolant temperature sensor if the values read do not correspond to the ones above.
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR064/EDC16_V48_PR064/EDC16_V4C_PR064

13B - 188
DIESEL INJECTION
Fault finding - Command summary table13B
V10 MR-372-J84-13B150$705.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Command summary table
Tool command Diagnostic tool title
SC001Write saved data
SC002Enter injector codes
SC003Save computer data
RZ001Fault memory
RZ002EGR programming adaptives
RZ005Programming
AC001Preheating unit
AC002EGR solenoid valve
AC004Turbocharging solenoid valve
AC011Rail pressure regulator
AC014Damper flap
VP010Enter VIN
MR-372-J84-13B150$705.mif

13B - 189
DIESEL INJECTION
13B
V10 MR-372-J84-13B150$752.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of commands
SC001
WRITE SAVED DATA
NOTESAll data must be backed up with command SC003 Backup computer data for this
command to be run.
Writing is carried out after the computer has been reprogrammed or replaced.
Confirming this command writes the data backed up using command SC003 Backup computer data.
The data is as follows:
– Vehicle-specific idle speed.
– Options available on the vehicle and managed by the computer (Example: Air conditioning).
– Injector calibration codes (if the vehicle is fitted with IMA).
– Programming of exhaust gas recirculation valve data.
They will configure the computer and will enable it to avoid:
– engine malfunction after reprogramming or replacing the computer,
– faulty interpretation of information provided by the CLIP tool.
AFTER REPAIRRestart the conformity check from the beginning.
EDC16_V44_SC001/EDC16_V48_SC001/EDC16_V4C_SC001
MR-372-J84-13B150$752.mif

13B - 190
DIESEL INJECTION
Fault finding - Interpretation of commands13B
V10 MR-372-J84-13B150$752.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
SC002
ENTER INJECTOR CODES
NOTESThis command is carried out after the replacement of the injectors, and only if the
vehicle is configured with IMA (ET104 Injector code use YES).
If this command is not run, the fault DF276 Injector code programming will be
present.
IMPORTANT
Letters Q and J, and figures 0 and 9 are not used in IMA codification.
If these characters are used the entry will be invalid.
Cylinder no. 1 is the cylinder located at the engine flywheel end.
Procedure to be followed:
– Read the 6-character alphanumeric codes etched on the upper section of the injector bodies.
– Select the cylinder number for the cylinder concerned in the Desired column, then confirm.
– Enter the injector code displayed for the cylinder.
– Enter the new codes for each cylinder, then confirm.
– When the command is completed, the modified codes appear in the Current column.
– Check that the codes correspond to those read earlier.
– If the codes entered appear in neither the Current column nor the Desired column, check the codes read and
make sure the data has been entered correctly.
– Exit fault finding mode.
– Switch off the ignition and wait 30 seconds.
– Switch the ignition back on and check for faults.
–The DF276 Injector code programming should be stored.
If the fault is still present, the command has not been run correctly.
Start the procedure again and follow the instructions.
Switch off the ignition.
If all these checks still do not enable the command to be confirmed, contact the Techline.
AFTER REPAIRRestart the conformity check from the beginning.
EDC16_V44_SC002/EDC16_V48_SC002/EDC16_V4C_SC002