Seat Ibiza 2020 Directive 2014/53/EU Bluetooth
Manufacturer: SEAT, Model Year: 2020, Model line: Ibiza, Model: Seat Ibiza 2020Pages: 406, PDF Size: 9.22 MB
Page 261 of 406
Page 48 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
5.8 TABLE: Backfeed safeguard in battery backed up s upplies
N/A
Location Supply
voltage (V) Operating and fault
condition Time (s) Open - circuit
voltage (V) Touch
current (A) ES Class
Supplementary information:
Abbreviation: SC= short circuit, OC= open circuit
6.2.2 TABLE: Power source circuit cl assifications
P
Location Operating and
fault condition Voltage (V) Current (A) Max.
Power 1)
(W) Time (S) PS class
Mains part - 1 2 V d.c. - - - PS3
(Declared)
Speaker
output Worst - case fault 7. 44 1.8 6
( calculated ) 13. 84 3 PS1
CN501
(49, GND) /
LCD PMR Worst - case fault 1.70 0.0 1 0.0 2 3 PS1
CN951
(51, GND) /
KEY_POW ER Worst - case fault 3.2 4 0.10 0.3 2 3 PS1
CN951
(17,GND) Worst - case fault 3.3 1 3.9 2 13. 1 0 3 PS1
CN951
(1, GND) /
SYS 5.2 Worst - case fault 4. 30 8. 2 0 35.30 5
PS2
CN951
(15, GND) /
VCC *) W orst - case fault 7.6 1 12. 6 0 95.90 5
PS2
Supplementary information:
Abbreviation: SC= short circuit; OC= open circuit
1) Measured after 3 s for PS1 and measured after 5 s for PS2 and PS3.
PS3: All combustible materials except for PS2 and PS1 parts below.
PS2: Monitor circuit and keyboard circuit.
*) LCD module and keyboard power line .
Page 262 of 406
Page 49 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
6.2.3.1 TABLE: Determination of Arcing PIS
N/A
Location Open circuit voltage
after 3 s (V pk ) Measured r.m.s
current (A)
Calculated value
Arcing PIS?
Yes / No
S upplementary information:
6.2.3.2 TABLE: Determination of resistive PIS
P
Location Operating and fault condition Dissipate power (W) Arcing PIS?
Yes / No
Supplementary information:
Abbreviation: SC= short circuit; OC= open circuit
All components l ocated within PS3 and PS2 are considered as resistive PIS.
A combination of voltmeter, VA and ammeter IA may be used instead of a wattmeter.
If a separate voltmeter and ammeter are used, the product of (VA x IA) is used to determine Resistive PIS
classific ation.
A Resistive PIS: (a) dissipates more than 15 W, measured after 30 s of normal operation, or (b) under
single fault conditions has either a power exceeding 100 W measured immediately after the introduction of
the fault if electronic circuits, regulat ors or PTC devices are used, or has an available power exceeding 15
W measured 30 s after introduction of the fault.
8.5.5 TABLE: High pressure lamp
N/A
Lamp manufacturer Lamp type Explosion method Longest axis of
glass particle
(mm) Particle found
bey ond 1 m
Yes / No
Supplementary information:
Page 263 of 406
Page 50 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
9.6 TABLE: Temperature measurements for wireless power transmitters
N/A
Supply voltage (V) ................................ .......... :
Max. transmit power of transmitter (W) .......... :
Foreign objects w/o receiver and
direct contact with receiv er and
direct contact with receiver and at
distance of 2 mm with receiver and at
distance of 5 mm
Object
( o
C) Ambient
( o
C) Object
( o
C) Ambient
( o
C) Object
( o
C) Ambient
( o
C) Object
( o
C) Ambient
( o
C)
Supplementary information:
5.4.1.4 ,
9.3 , B.1.5 ,
B.2.6 TABLE: Temperature measurements
P
Supply voltage (V) ................................ .......... : 14.4 V
d.c. 14.4 V
d.c. 14.4 V
d.c.
Ambient temperature during test T
amb ( C) .... : 20.9 25 1)
70 2)
Maximum measured temperature T of part/at:
T ( C) Allowed
T
max ( C)
1. Display PCB near IC100 43.1 - 92.2 130
2. Display panel body (Not accessible) 44.6 - 93.7 -
3. Connector body (CN310) 41.3 - 90.4 -
4. PCB near SD card slot 49.3 - 98.4 130
5. Main PCB near CN150 47.9 - 97.0 130
6. Main PCB near IC 402 68.3 - 117.4 130
7. Main PCB near L304 45.6 - 94.7 130
8. Main to Display connector body (CN951) 51.3 - 100.4 -
9. PCB near BD7820 61.1 - 110.2 130
10. PCB near CN151 56.5 - 105.6 130
11. Amp IC body (IC163) 63.4 - 112.5 -
12. PCB near C298 58.4 - 107.5 130
13 . Main to Antenna connector body (CN990) 54.4 - 103.5 -
14. Antenna PCB near IC182 64.2 - 113.3 130
15. Monitor body 36.3 40.4 - 71
Page 264 of 406
Page 51 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
16. Power key knob body 24.5 28.6 - 60
17. Enclosure near media button 26.9 31.0 - 77
18. Frame body (Not accessib le) 31.4 - 80.5 -
19. Metal enclosure body (Not accessible) 42.0 - 91.1 -
Ambient temperature See
above See
above See
above -
Temperature T of winding: t
1 (°C)
R
1 ( ) t
2 (°C)
R
2 ( ) T ( C) Allowed
T
max ( C) Insulation
class
Supplementary in formation:
Note 1. The temperatures for accessible parts are adjusted to reflect a value of 25 °C .
Note 2. Maximum operating Temperature pe rmitted by the Manufacturer(Tma) is 70 C .
B.2.5 TABLE: Input test
P
U (V) Hz I (A) I rated (A) P (W) P rated (W ) Fuse No I fuse (A) Condition/status
10.2 - 1.73 - 17.65 - - -
Max. normal
load condition.
12.0 - 1.67 3.5 20.04 - - -
Max. normal
load condition.
14.4 - 1.69 - 24.34 - - -
Max. normal
load condition.
Supplementary information:
Max. normal load condit ion : The equipment is operated in such a way as to deliver one - eighth of the NON -
CLIPPED OUTPUT POWER to the RATED LOAD IMPEDANCE ( 4Ω ) using the standard signal described
in Annex E and Max. brightness for LCD module.
Page 265 of 406
Page 52 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
B.3, B.4 TABLE: Abnormal operatin g and fault condition tests
P
Ambient temperature T
amb ( C) ................................ ..................... : 2 0 - 2 2
Power source for EUT: Manufacturer, model/type, outputrating .. : -
Component No. Condition Supply
voltage
(V) Test
time Fuse no. Fuse
current
(A) Observation
Ventilation
openings Blo ck ed 14.4 2 h - - FI : 1. 6 9 A, NO,
CT (Monitor body : 3 6.6 C,
Power key knob body : 2 4.0
C, Enclosure near media
button : 2 6 . 9 C, Ambient :
2 0 .6 C, NCD, NH
Speaker output Max. non -
clipped output 14.4 2 h - - FI : 2.96 A, NO,
CT ( Amp IC body (IC163) :
64. 0 C , Monitor body : 3 6.6
C, Power key knob body :
2 4.3 C, Enclosure near
media button : 2 7.0 C,
Ambient : 2 0.6 C, NCD, NH
Speaker output SC 14.4 1 h - - FI : 0.5 - 1. 05 A , IP , NCD,
NH
IC101(3,8) SC 14.4 1 h - - FI : 0.5 A, CD(IC101), NH
IC902( 1,6) SC 14.4 1 h - - FI : 0.5 A, CD(IC902), NH
Supplementary information:
Abbreviation:
FI – Final Input Current; IP – Internal protection operated; NO – Normal Operated;
CD – Component Damaged (list damaged components); NCD – No Component Damaged;
NH – No Hazard ; CT – Constant temperatures were obtained (list components: temperature;);
NB – No indication of dielectric breakdown; YB – Dielectric breakdown (indicate time and location);
NC – Cheesecloth remained intact; YC – Cheesecloth charred or flamed;
Page 266 of 406
Page 53 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
M.3 TABLE: Protection circuits for batteries provided within the equipment
N/A
Is it possible to install the battery in a reverse polarity position? ...... :
Equipment Specification Charging
Voltage (V) Current (A)
Manufacturer/type Battery specif ication
Non - rechargeable batteries Rechargeable batteries
Discharging
current (A) Unintentional
charging
current (A) Charging Discharging
current (A) Reverse
charging
current (A) Voltage (V) Current (A)
Note: The tests of M.3.2 are appli cable only when above appropriate data is not available.
Specified battery temperature ( o
C) ................................ ................... :
Componen
t No. Fault
condition Charge/
discharge mode Test
time Temp.
( o
C) Current
(A) Voltage
(V) Observation
Supplementary information:
Abbreviati on: SC= short circuit; OC= open circuit NL= no chemical leakage; NS= no spillage of liquid; NE=
no explosion; NF= no emission of flame or expulsion of molten metal.
M.4.2 TABLE: Charging safeguards for equipment containing a secondary lithium
battery N/ A
Maximum specified charging voltage (V) ................................ ..... :
Maximum specified charging current (A) ................................ ..... :
Highest specified charging temperature ( o
C) .............................. :
Lowest specified charging temperature ( o
C) ............................... :
Battery
manufacturer/type Operating
and fault
condition Measure ment Observation
Charging
voltage (V) Charging
current (A) Temp.
( o
C)
Supplementary information:
Abbreviation: SC= short circuit; OC= open circuit; MSCV= maximum specified charging voltage; MSCC=
maximum specified charging current; HSCT= highe st specified charging temperature; LSCT= lowest
specified charging temperature
Page 267 of 406
Page 54 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
Q.1 TABLE: Circuits intended for interconnection with building wiring (LPS)
N/A
Output
Circuit Condition U
oc (V) Time (s) I
sc (A) S (VA)
Meas. Limit Meas. Limit
Supplementary Information:
SC=Short circuit, OC=Open circuit
T.2, T.3,
T.4, T.5 TABLE: Steady force test
N/A
Part/Location Material Thickness
(mm) Probe Force
(N) Test
Duration
(s) Observation
Supplementary information:
T.6, T. 9 TABLE: Impact test
P
Location/part Material Thickness
(mm) Height
(mm) Observation
Front, Top / Monitor PC /ABS Min. 1.5 1 300 No damaged, no hazard
Front / Keyboard PC/ABS Min. 1.5 1 300 No damaged, no hazard
Supplementary information:
T.7 TABLE: Drop test
N/A
Location/part Material Thickness
(mm) Height
(mm) Observation
Supplementary information:
Page 268 of 406
Page 55 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
T.8 TABLE: Stress relief test
P
Location /Part Material Thickness
(mm) Oven Temperature
( C) Duration
(h) Observation
Monitor , Keyboard PC /ABS Min. 1.5 86.0 7 No shrinkage or
distortion.
No defeat its
safeguard function.
Supplementary information:
X TABLE: Alternative method for determining minimum clearances distances
N/A
Clearance distanced
between: Peak of working voltage
(V) Require d cl
(mm) Measured cl
(mm)
Supplementary information:
Page 269 of 406
Page 56 of 88 Report No. : 60404489 001
IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict
TR F No. IEC62368_1 C
4.1.2 TABLE: Critical components information
P
Object / part No. Manufacturer/
trademark Type / model Technical data Standard Mark(s) of
conformity 1)
Plastic
Enclosure LG CHEM LTD LUPOY GN -
5007F(#) V - 0 UL 94 UL ( E67171 )
Alternate Interchangeable Interchangeable Min. HB UL 94 UL
- Description: Interchangeability based on specified ratings
Metal Enclosure Interchangeable Interchangeable AL or EGI(SECC)
or GI(SGCC) or
NI or ALDC or
MG or SUS or
STS or NSP or
STEEL, Min. 0.4
thickness IEC 62368 - 1 Tested in
equipment
- Description: Interchangeability based on specified ratings and dimensions
PCB ZHEJIANG
HUABANG
ELECTRONICS
CO LTD H - 01 V - 0 UL 796 UL ( E251053 )
Alternate HYUN WOO
INDUST RIAL
CO LTD 3 V - 0 UL 796 UL (E131308)
Alternate Interchangeable Interchangeable Min. V - 1 UL 796 UL
- Description: Interchangeability based on specified ratings
LCD Panel LG Display Co.,
Ltd. LA065WV1 6.5 inch ,
( 800 x 480 ) IEC 62368 - 1 Tested in
equipm ent
Alternate LG Display
(Paju) Co., Ltd. LA065WV3 6.5 inch ,
( 800 x 480 ) IEC 60065 T Ü V - Rh
(JPTUV -
080511)
Alternate Giantplus
Technology Co.,
LTD. GPM1696A0 6.5 inch ,
( 800 x 480 ) IEC 60065 SGS F imko
(FI - 37636)
Mains connector
material KURARAY CO
LTD GN2330(#) V - 0 UL 94 UL (E90350)
Alternate Interchangeable Interchangeable Min. V - 1 UL 94 UL
- Description: Interchangeability based on specified ratings
Fuse ST VN5E010MHTR -
E 13A Sw itch off ISO/TS
16949:2009 9136.STM2
Supplementary information:
1)
Provided evidence ensures the agreed level of compliance. See OD - 2039.
Page 270 of 406
Page 57 of 88 Report No. : 60404489 001
IEC 62368 - 1 – ATTACHMENT 1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62368_1 C ATTACHMENT TO TEST R EPORT
IEC 62368 - 1
EUROPEAN GROUP DIFFE RENCES AND NATIONAL DIFFERENCES
(AUDIO/VIDEO, INFORM ATION AND COMMUNICATION T ECHNOLOGY EQUIPMENT - PART 1: SAFETY
REQUIREMENTS)
Differences according to ................ :
EN 62368 - 1:2014+A11:2017
Attachment Form No . ..................... :
EU_GD_IEC62368_1B_II
Attachment Originator ................... :
Nemko AS
Master Attachment ......................... :
Date 2017 - 09 - 22
Copyright © 2017 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE),
Geneva, Switzerland. All rights reserved.
CENELEC COMMON MODIFICATIONS (EN)
P
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62368 - 1:2014 are prefixed “Z”. P
CONTENTS Add the following annexes:
Annex ZA (normative) Normative references to international publications
with their corresponding European publications
Annex ZB (normative) Special nat ional conditions
Annex ZC (informative) A - deviations
Annex ZD (informative) IEC and CENELEC code designations for flexible
cords P
Delete all the “country” notes in the reference document (IEC 62368 - 1:2014) according
to the foll owing list:
P