torque SSANGYONG KORANDO 1997 Service Repair Manual

1B3 -- 68 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
5. Install the flange, vibration damper and crankshaft
belt pulley.
Notice
Replace front radial seal if necessary.
6. Install the generator bracket.
TighteningFront25 N∙m (18 lb-ft)Tightening
To r q u eSide25 N∙m (18 lb-ft)
7. Install the generator.
TighteningTorqueUpper--25N∙m (18 lb-ft)TighteningTorqueLow -- 25 N∙m (18 lb-ft)
8. Install the cylinder head cover.
Tightening Torque10 N∙m(89lb-in)
9. Tighten the injection pump mounting bolts.
Tightening Torque23 N∙m (17 lb-ft)

OM600 ENGINE MECHANICAL 1B3 -- 69
D AEW OO M Y_2000
10. Install the fuel filter.
Tightening Torque25 N∙m (18 lb-ft)
11. Install the vacuum pump.
Tightening Torque10 N∙m(89lb-in)
12. Install the power steering pump.
Tightening Torque23 N∙m (17 lb-ft)
13. Install the power steering pump pulley
Tightening Torque32 N∙m (24 lb-ft)
14. Install the guide pulley bracket
Tightening Torque9N∙m(80lb-in)

1B3 -- 70 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
15. Install the guide pulley (22) and fit the closing cover
(20).
Tightening Torque23 N∙m (17 lb-ft)
16. Replace the gasket (3) and install the cylinder head
cover (2).
Tightening Torque10 N∙m(89lb-in)
17. Install the cooling fan belt pulley and fan clutch.
18. Install the belt tensioning device and then install the
belt.
19. Install the cooling fan.
20. Fill the engine oil and check oil leaks by running the
engine.

1B3 -- 72 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
Tools Required
601 589 03 43 00 Oil Seal Assmbler
Removal Procedure
1. Remove the bolts (3, 6) from end cover, By pulling
out the lugs (arrow), remove the cover.
Notice
Be careful not to damage the oil pan gasket.
2. Remove the radial seal (4) with care not to damage
thesealingsurface.
Installation Procedure
1. Thoroughly clean the sealing surface of end cover
and apply Loctite 573.
2. Clean the groove of radial seal.
3. Apply Loctite 573 on the bolts and install the end
cover.
Tightening Torque10 N∙m(89lb-in)
Notice
Be careful not to damage the oil pan gasket.
4. Install the inner oil seal assembler to the crankshaft
flange.
Oil Seal Assembler 601 589 03 43 00

1B3 -- 78 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
Installation Procedure
1. Install the hub.
Notice
Exactly align the woodruff key and the groove of hub
(arrow).
2. Install the washer (7) and tighten the bolt (6).
Washer (new) :1 EA200 N∙m (148 lb-ft) + 90_
3. Install the vibration damper.
Notice
Exactly align and insert onto the straight pin.
4. Install the belt pulley.
Tightening Torque25 N∙m (18 lb-ft)
Notice
Align the alignment marks.

OM600 ENGINE MECHANICAL 1B3 -- 79
D AEW OO M Y_2000
5. Install the timing sensor bracket.
Notice
See the ’TDC setting’.
6. Install the cooling fan pulley.
Tightening Torque10 N∙m(89lb-in)
7. Install the cooling fan.
8. Install the fan belt.
9. Remove the engine lock.

OM600 ENGINE MECHANICAL 1B3 -- 89
D AEW OO M Y_2000
8. Thoroughly clean the oil gallery.
9. Select a proper new bearing shells with reference to
table.
10. Coat the new bearing shells with oil and insert into
the crankcase and into the crankshaft bearing caps.
Notice
Do not mix up upper and lower crankshaft bearing
shells.
11. Install the bearing caps according to marking and
tighten the 12--sided stretch bolts.
Tightening Torque35-- 40 N∙m (26-- 30 lb-ft)
Notice
No. 1 is vibration damper side.
12. Measure crankshaft bearing diameters (E).
Extension 366 589 00 21 05
13. Measure at 3 points (A, B and C) and if the average
value of B and C is less than A’s value, the average
value of B and C is the mean value and if more than
A’s value, A’s value is the mean value.
14. Measure crankshaft bearing journal diameter (F).
Notice
When measured in A and B, the runout should not
exceed 0.010mm.

OM600 ENGINE MECHANICAL 1B3 -- 91
D AEW OO M Y_2000
Notice
If the max. length of bolts(L) exceed 63.8mm, re-
place them.
19. Coat the new crankshaft with engine oil and place it
on the crankcase.
20. Install the crankshaft bearing caps according to
marking and tighten the bolts.
Tightening Torque55 N∙m (41 lb-ft) + 90_
Notice
Install from No. 1 cap.
22. Rotate the crankshaft with hand and check whether
it rotates smoothly.
23. Measure crankshaft bearing axial clearance.
Clearance0.100 -- 0.245 mm
Notice
If the clearance is out of standard, adjust the axial
clearance of crankshaft bearing by replacing the
thrust washers.
Dial Gauge 001 589 53 21 00
Dial Gauge Holder 363 589 02 21 00
Notice
The same thickness of thrust washers should be
installed on both sides of the thrust bearing.

1B3 -- 92 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
24. Insert the new connecting rod bearing shells into the
connecting rod and connecting rod bearing cap and
tighten the 12--sided stretch bolts (11).
Tightening Torque40 N∙m (30 lb-ft) + 90_
25. Measure inner diameter of connecting rod bearing.
26. Measure connecting rod bearing journal diameter
(K).
Notice
Refer to measurement of the crankshaft bearing
journal diameter.
27. Measure the radial clearance (L) of the connecting
rod bearing.
Example) Measured value ’J’ = 47.700mm
Measured value ’K’ = 47.653mm
——————————————
Clearance ’L’ = 0.047mm
Radial Clearance ’L’0.026 -- 0.068mm
Notice
If the clearance is out of standard, adjust the radial
clearance of connecting rod bearing by replacing the
connecting rod bearing shells.
28. Remove the connecting rod bearing cap.
29. Install the piston.
30. Rotate the crankshaft by hand and check whether it
rotates smoothly.
31. If the bearings are damaged,
-- replace the oil presser relief valve.
-- clean the oil pump and oil filter housing carefully
and replace the hose if necessary.
Notice
After assembling the engine, check the camshaft
timing, adjust the start of fuel injection and check the
TDC sensor bracket setting.
32. Fill oil and run the engine and then check the oil
pressure and oil level.
Notice
Install the original oil filter element and then change
the engine oil and oil filter element after 1,000 --
1,500km.

OM600 ENGINE MECHANICAL 1B3 -- 95
D AEW OO M Y_2000
Tools Required
602 589 00 40 00 Engine Lock
Removal & Installation Procedure
1. Install the engine lock.
Engine Lock 602 589 02 40 00
2. Remove the 12-- sided stretch bolts (4).
Installation Notice
Tightening Torque45 N∙m (33 lb-ft) + 90_
Notice
If the length ’L’ of bolts exceeds 22.5mm, replace
the bolts.
3. Remove the flywheel (3), if equipped with manual
transmission.
Installation Notice
Correctly align the position of dowel pin (2).