SSANGYONG NEW ACTYON SPORTS 2012 Service Manual

02-578710-01
STICS Outside Rearview Mirror Folding/Unfolding Control Circuit ▶
If you remove the ignition switch and open the driver's door with the sunroof open, the chime
buzzer sounds.
As soon as you close the driver's door or the sunrooof, the chime buzzer output stops.
However, when operating conditions in step (1) are met after the operation in step (2), the
chime buzzer will not sound again. If you turn the ignition swtich to the "ON" position again
and the operating contions in step (1) are met, the chime buzzer sounds again.
If the operating condtions for door ajar warning and sunroof open warning are met at the
same time, the sunroof open warning is activated preferentially. 1.
2.
3.
4. In order to prevent the driver from getting off the vehicle with the sunroof open, the reminder
function for the driver is added. This function is activated as follows:Sunroof open warning ▶

02-58
Circuit Diagram for Wiper ▶
4. CIRCUIT DIAGRAM

02-598710-01
Circuit Diagram for Door Lock Control ▶
The door ajar warning lamp in the instrument cluster does not come on even though the
tailgate is opened.

02-60
You can register up to 2 transmission codes to the remote control key.
The receiver does not output the received code during registration.
The remote control key should be coded using the diagnostic device. a.
b.
c.
1) Operating requirements
You should remove the ignition key.
2) Code registration requirement
You can register the code only using the diagnostic device.
3) Transmitter code registration
5. REKES Key Coding

02-618710-01
4) How to Code REKES Key
If you replace the REKES key or immobilizer & rechargeable key to new one, you should code the
REKES key using the diagnostic device. (maximum 5)
Connect the diagnostic device to the vehilce and select the vehicle type and system (RK-
STICS). When the following screen is displayed, select 'REMOCON CODING'. 1.
Remove the remote control key from the ignition key box and press 'Next'. Press the door
UNLOCK (PANIC) button on the remote control key once (for approx. 2 seconds or longer). 2.

02-62
When you code newly purchased remote control key:
When you lost the remote control key and purchase a new one, if you code only the newly
purchased one, the existing remote control key becomes unavailable. You must code the
newly purchased remote control key together with the existing one. -The first key coding completion screen is displayed with beep sound as follows: Press 'Next'
and perform the second remote control key coding in the same way. 3.
When the second key coding is completed, the following screen is displayed. Finish the
remote control key coding by pressing 'Previous'. 4.
Exit the diagnostic screen, remove the device from the diagnostic connector and perform the
function test for the remote control key. If it does not work well, perform the above procedures
again. 5.

02-630000-00
5) How to Register Transponder
Insert the ignition key into the key cylinder and turn it to the "ON" position.
Select the vehicle type and system (immobilizer) on the diagnosis program.
Select the Transponder registration menu and enter the password. (initial value is "0000") Select
"Next". 1.
2.
3.
Press "Next" with the first key in key box. 4.

02-64
Check the progress. 5.
If another key should be registered additionally, insert the second key into the key cylinder and
press "Next" within 10 seconds since the first transponder coding is complete. 6.

02-650000-00
Press "OK" button when the registration is complete. 7.
If the registration fails, press "Previous" button and perform the registration procedures again.

02-66
5) Pin Arrangement of Diagnostic Connector
Diagnosis connector is installed at the lower driver side instrument panel and it consists of 16
pins.
REKES key coding should be done using the diagnostic device.
▶Fuction For Each Terminal
Pin No. Function Pin No. Function
1 FFH diagnosis 9 Air bag
2 FFH forced driving 10 -
3 STICS 11 TCU
4 Ground 12 -
5 Signal ground 13 TCCU
6 CAN - HIGH 14 CAN - LOW
7 - 15 REKES key coding
8 - 16 Battery +
The REKES key coding is not performed by connecting the REKES coding terminal (No. 15) of
the diagnostic connector to the jump wire between the ground terminals.
(possible only diagnostic device)