stop start YAMAHA XSR 900 2022 Owners Manual

Special features
3-2
1
23
4
5
6
7
8
9
10
11
12
13 new cruising speed by pressing the
“SET–” side of the setting switch. If you
do not set a new cruising speed, when
you return the throttle grip, the vehicle
will decelerate to the previously set
cruising speed.
Deactivating the cruise control sys-
tem
Perform one of the following operations
to cancel the set cruising speed. The
“ ” indicator light will go off.

Turn the throttle grip past the
closed position in the deceleration
direction.

Apply the front or rear brake.

Disengage the clutch.

Shift gears
Press the power switch to turn off the
cruise control system. The “ ” indica-
tor light and the “ ” indicator light will
go off.
TIPTraveling speed decreases as soon as
the cruise control system is deactivat-ed; unless the throttle grip is turned.
Using the resume function
Press the “RES+” side of the cruise
control setting switch to reactivate the
cruise control system. The traveling
speed will return to the previously set
cruising speed. The “ ” indicator light
will come on.
WARNING
EWA16351
It is dangerous to use the resume
function when the previously set
cruising speed is too high for cur-rent conditions.TIPPressing the power switch while the
system is operating will turn the system
off completely and erase the previously set cruising speed. You will not be able
to use the resume function until a new
cruising speed has been set.
Automatic deactivation of the cruisecontrol systemThe cruise control system for this mod-
el is electronically controlled and is
linked with the other control systems.
The cruise control system will automat-
ically become deactivated under the
following conditions:
The cruise control system is not
able to maintain the set cruising
speed.

Wheel slip or wheel spin is detect-
ed. (If the traction control system
has not been turned off, the trac-
tion control system will work.)

The start/engine stop switch is set
to the “ ” position.

The engine stalls.

The sidestand is lowered.
When traveling with a set cruising
speed, if the cruise control system is
deactivated under the above condi-
tions, the “ ” indicator light will go off
and the “ ” indicator light will flash for
1. Deceleration direction
1
BEA-28199-E0.book 2 ページ ２０２１年１２月１日　水曜日　午後７時８分

Special features
3-3
1
234
5
6
7
8
9
10
11
12
13
4 seconds, and then go off.
When not traveling with a set cruising
speed, if the start/engine stop switch is
set to the “ ” position, the engine
stalls, or the sidestand is lowered, then
the “ ” indicator light will go off (the
“ ” indicator light will not flash).
If the cruise control system is automati-
cally deactivated, please stop and con-
firm that your vehicle is in good
operating condition.
Before using the cruise control system
again, activate it using the power
switch.
TIPIn some cases, the cruise control sys-
tem may not be able to maintain the set
cruising speed when the
vehicle is trav-
eling uphill or downhill.
When the vehicle is traveling up-
hill, the actual traveling speed may
become lower than the set cruising
speed. If this occurs, accelerate to
the desired traveling speed using
the throttle.

When the vehicle is traveling
downhill, the actual traveling
speed may become higher than the set cruising speed. If this oc-
curs, the setting switch cannot be
used to adjust the set cruising
speed. To reduce the traveling
speed, apply the brakes. When the
brakes are applied, the cruise con-
trol system will become deactivat-
ed.
EAU91323
“D-MODE”“D-MODE” is an electronically con-
trolled engine performance system.
WARNING
EWA18440
Do not change the drive mode whilethe vehicle is moving.
The “D-MODE” system consists of 4
different control maps which regulate
engine response and output, thus pro-
viding you with a selection of modes to
fit your preferences and the riding envi-
ronment.
D-MODE 1
- Sporty engine response
D-MODE 2 - Moderate engine re-
sponse
D-MODE 3 - Mild engine response
D-MODE 4 - Mild engine response and
limits engine outputTIP
The current “D-MODE” setting is
shown in the MODE display. (See
page 4-12.)

The current “D-MODE” setting is
saved when the vehicle is turned
off.

The “D-MODE” is controlled by the
BEA-28199-E0.book 3 ページ ２０２１年１２月１日　水曜日　午後７時８分

Special features
3-5
1
234
5
6
7
8
9
10
11
12
13
more information on
“TCS-MODE”.

When “TCS-MODE” has been set
to “OFF”, the traction control sys-
tem, SCS and LIF systems are allturned off together.WARNING
EWA15433
The traction control system is not a
substitute for riding appropriately
for the conditions. Traction control
cannot prevent loss of traction due
to excessive speed when entering
turns, when accelerating hard at a
sharp lean angle, or while braking,
and cannot prevent front wheel slip-
ping. As with any vehicle, approach
surfaces that may be slippery with
caution and avoid especially slip-pery surfaces.
When the vehicle power is on, the trac-
tion control system automatically turns
on. The traction control system can be
turned on or off manually only when the
key is in the “ON” position and the mo-
torcycle is stopped.
TIPSet “TCS-MODE” to “OFF” to help free
the rear wheel if the motorcycle gets
stuck in mud, sand, or other soft surfac-es.NOTICE
ECA16801
Use only the specified tires. (See
page 7-16.) Using different sized
tires will prevent the traction control
system from controlling tire rotationaccurately.
SCS
The slide control system regulates en-
gine power output when a sideward
slide is detected in the rear wheel. It ad-
justs power output based on data from
the IMU (Inertial Measurement Unit).
This system supports the traction con-
trol system to contribute to a smoother
ride.
LIF
The lift control system reduces the rate
at which the front wheel rises during ex-
treme acceleration, such as during starts or out-of-corner exits. When
front-wheel lift is detected, engine pow-
er is regulated to slow front-wheel lift
while still providing good acceleration.
BEA-28199-E0.book 5 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-3
1
2
34
5
6
7
8
9
10
11
12
13 To unlock the steering
Push the key in and turn it to “OFF”.
EAU66057
Handlebar switchesLeft
Right
EAU91630
Dimmer/Pass switch “ / /PASS”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
While the headlight is set on low beam,
push the switch down towards “PASS”
to flash the high beam and to mark the
start of each lap when using the lap tim-
er.
EAU66040
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When re-
leased, the switch returns to the center
1. Push.
2. Turn.12
1. “MODE” switch
2. MODE up switch
3. MODE down switch
4. Cruise control switches
5. Hazard switch “ ”
6. Horn switch “ ”
7. Turn signal switch “ / ”
8. Dimmer/Pass switch “ / /PASS”
RESSET
MODE
P
ASS
23
4
5
6
1
8 7
1. Stop/Run/Start switch “ / / ”
2. Wheel switch “ ”
1 1 12 2
BEA-28199-E0.book 3 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-4
1
2
345
6
7
8
9
10
11
12
13
position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU66030
Horn switch “ ”
Press this switch to sound the horn.
EAU66061
Stop/Run/Start switch “ / / ”
To crank the engine with the starter, set
this switch to “ ”, and then push the
switch down towards “ ”. See page
6-2 for starting instructions prior to
starting the engine.
Set this switch to “ ” to stop the engine
in case of an emergency, such as when
the vehicle overturns or when the throt-
tle cable is stuck.
EAU91670
Hazard switch “ ”
Use this switch to turn on the hazard
lights (simultaneous flashing of all turn
signal lights). The hazard lights are
used in case of an emergency or to
warn other drivers when your vehicle is
stopped where it might be a traffic haz-
ard.
The hazard lights can be turned on or off only when the key is in the “ON” po-
sition. You can turn the main switch to
the “OFF” or “LOCK” position, and the
hazard lights will continue to flash. To
turn off the hazard lights, turn the main
switch to the “ON” position and operate
the hazard switch again.
NOTICE
ECA10062
Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-tery may discharge.
EAU73952
Cruise control switches
See page 3-1 for an explanation of the
cruise control system.
EAU91365
MODE switches
Use the MODE switches to change the
“D-MODE” and “TCS-MODE” located
on the left side of the main display.
There are three mode controls:
MODE up switch
- press this switch to
change the selected mode setting up-
ward.
“MODE” switch - press this switch to toggle left to right between “D-MODE”
and “TCS-MODE”.
MODE down switch
- press this switch
to change the selected mode setting
downward.
TIP
When in “D-MODE 1”, pressing
the MODE up switch will cycle to
“D-MODE 4”. When in “D-MODE
4”, pressing the MODE down
switch will not cycle to “D-MODE
1”.

The “TCS-MODE” can only be
turned off from the main display.
Select “TCS-MODE” with the
“MODE” switch, then press and
hold the MODE up switch until
“OFF” is displayed.

To turn the traction control system
back on, use the MODE down
switch.

When “TCS-MODE” has been set
to “OFF”, the traction control sys-
tem, SCS and LIF systems are all
turned off together.

See page 4-12 for more informa-
tion on the MODE display.

See page 3-4 for more information
BEA-28199-E0.book 4 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-7
1
2
34
5
6
7
8
9
10
11
12
13

Do not change the drivetrain spec-
ifications (chain, sprockets,
wheels, tires, etc.).

Do not remove or alter the O2 sen-
sor, air induction system, or ex-
haust parts (catalysts or EXUP,
etc.).

Maintain the drive chain properly.

Maintain correct tire pressure.

Maintain proper brake pedal
height to prevent rear brake from
dragging.

Do not operate the vehicle in an
extreme manner. For example, re-
peated or excessive opening and
closing of the throttle, racing, burn-
outs, wheelies, extendedhalf-clutch use, etc.
EAU91500
ABS warning light “ ”
In normal operation, the ABS warning
light comes on when the vehicle is
turned on, and goes off after traveling
at a speed of 5 km/h (3 mi/h) or higher.TIPIf the warning light does not work as de-
scribed above, or if the warning light comes on while riding, the ABS may not
work correctly. Have a Yamaha dealer
check the vehicle as soon as possible.
WARNING
EWA21120
If the ABS warning light does not
turn off after reaching 5 km/h (3
mi/h), or if the warning light comes
on while riding: 
Use extra caution to avoid pos-
sible wheel lock during emer-
gency braking.

Have a Yamaha dealer check thevehicle as soon as possible.
EAU88350
Immobilizer system indicator light
“”
When the main switch is turned off and
30 seconds have passed, the indicator
light will flash steadil
y to indicate the im-
mobilizer system is enabled. After 24
hours have passed, the indicator light
will stop flashing, however the immobi-
lizer system is still enabled.TIPWhen the vehicle is turned on, this light should come on for a few seconds and
then go off. If the light does not come
on, or if the light remains on, have a
Yamaha dealer check the vehicle.
Transponder interference
If the immobilizer system indicator light
flashes in the pattern, slowly 5 times
then quickly 2 times, this could be
caused by transponder interference. If
this occurs, try the following.
1. Make sure there are no other im- mobilizer keys close to the main
switch.
2. Use the code re-registering key to start the engine.
3. If the engine starts, turn it off, and try starting the engine with the
standard keys.
4. If one or both of the standard keys do not start the engine, take the
vehicle and all 3 keys to a Yamaha
dealer to have the standard keys
re-registered.
EAU91472
Stability control indicator light “ ”
This indicator light flashes when the
traction control system, SCS, or LIF
BEA-28199-E0.book 7 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-8
1
2
345
6
7
8
9
10
11
12
13
systems engage while riding. When
“TCS-MODE” is set to “OFF”, the indi-
cator will come on.
TIPWhen the vehicle is turned on, this light
should come on for a few seconds and
then go off. If the light does not come
on, or if the light remains on, have aYamaha dealer check the vehicle.NOTICE
ECA27222
When turning the main switch on,
avoid any movement or vibration of
the vehicle as it may interfere with
the initialization of the IMU. If this oc-
curs, the traction control system will
not operate and the “TCS-MODE”
display will read “OFF” until the IMUcan initialize.
EAU88362
Oil pressure and Coolant tempera-
ture warning light “ ”
This warning light comes on if the en-
gine oil pressure is low or if the coolant
temperature is high. If this occurs, stop
the engine immediately.
TIP
When the vehicle is first turned on,
this light should come on until the
engine is started.

If a malfunction is detected, this
light will come on and the oil pres-sure icon will flash.
NOTICE
ECA22441
If the oil pressure and coolant warn-
ing light does not go off after start-
ing the engine or if it comes on while
the engine is running, stop the vehi-
cle and engine immediately.
If the engine is overheating, the
coolant temperature warning
icon will come on. Let the en-
gine cool. Check the coolant
level (see page 7-37).

If the engine oil pressure is low,
the oil pressure warning icon
will come on. Check the oil level
(see page 7-12).

If the warning light remains on
after letting the engine cool and
confirming the proper oil level,
have a Yamaha dealer check the
vehicle. Do not continue to op-
erate the vehicle!
EAU88370
Auxiliary system warning light “ ”
This warning light comes on if a prob-
lem is detected in a non-engine-related
system.TIPWhen the vehicle is turned on, this light
should come on for a few seconds and
then go off. Otherwise, have a Yamahadealer check the vehicle.
BEA-28199-E0.book 8 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-14
1
2
345
6
7
8
9
10
11
12
13
To start the timer, press the dimmer/
pass switch down towards “PASS”.
Each press of the dimmer/pass switch
will increase the lap count by 1 and re-
set the current lap timer.
To pause the lap timer, press the wheel
switch inward.
To unpause the timer, press the dim-
mer/pass switch down towards “PASS”
and the timer will resume without count-
ing a new lap.
To exit the lap time mode, turn it off in
the settings MENU. (See page 4-16.)
TIP
The engine must be running to start the lap timer.

The headlight will flash when the
dimmer/pass switch is pressed.

Whenever the lap timer is paused,
it can be resumed using the dim-mer/pass switch.
Brake control icon “BC”
This icon is replaced by the auxiliary
system warning and coolant tempera-
ture warning indicators when they are
activated.
For more information on the BC system
see “BC” on page 3-6.
Error mode warning “Err”
When an internal error occurs (e.g.,
communication with a system controller
has been cut off), the error mode warn-
ing will appear as follows.
“Err” and “ ” indicator light indicates
an ECU error.
“Err” only indicates an ABS ECU error.
TIPDepending on the nature of the error,
the display may not function properly
and the traction control system settings
may be impossible to change. Addition- ally, ABS may not function properly.
Use extra care when braking and have
a Yamaha dealer check the vehicle im-
mediately.
Auxiliary system warning “ ”
This icon appears if a problem is de-
tected in a non-engine-related system.
Coolant temperature warning “ ”
This icon appears if the coolant temper-
ature reaches 116 
C (241 F) or high-
er. Stop the vehicle and turn off the
engine. Allow the engine to cool.NOTICE
ECA10022
Do not continue to operate the en-gine if it is overheating.
Oil pressure warning “ ”
This icon appears when the engine oil
pressure is low. When the vehicle is
first turned on, engine oil pressure has
yet to build, so this icon will come on
and stay on until the engine has been
started.
1. Lap count
2. Current lap time
3. Latest/Previous lap time
LAP
02
LATEST
00:12.34
00:30.23
2
1
3
BEA-28199-E0.book 14 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-17
1
2
34
5
6
7
8
9
10
11
12
13 “Vehicle Setting”
The vehicle setting module allows you
to adjust setting for the BC and quick
shifter.
BC
The brake control system has two set-
tings, BC1 and BC2. Select BC1 when
only standard ABS is desired. Select BC2 to have the brake control system
further regulate brake pressure while
cornering to suppress lateral wheel slip.
TIPFor skilled riders and when riding at the
track, due to varying conditions, the
BC2 brake system may engage sooner
than expected relative to your desired
cornering speed or intended corneringline.
Quick shifterThe quick shifter indicators are divided
into QS and QS sections. QS
and QS are not linked and can be in-
dependently turned on or off.
The quick shifter can be set to ON or
OFF.OFF turns the respective upshift or
downshift function off, and the clutch le-
ver must then be used when shifting in
that direction.
TIPIf the quick shifter setting cannot be
changed: turn the engine off with the
gear position set to neutral, thenchange the setting.
“Shift Indicator”
This module allows a custom shift indi-
cator to be set. When the engine r/min
(rotations per minute) are in the speci-
fied range, the gear indicator will flash.
This module has 3 options:
“IND Mode” - the shift indicator can be
turned ON/OFF
BC SettingQS Setting
km/h
Vehicle Setting
km/h
BC Setting
BC
2
km/h
QS Setting
QS
ONQSON
km/h
Shift Indicator
IND Mode ONIND Start 8000 r/minIND Stop 10000 r/min
BEA-28199-E0.book 17 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-18
1
2
345
6
7
8
9
10
11
12
13
“IND Start” - the r/min at which the indi-
cator starts flashing can be chosen.
Once selected, rotate the wheel switch
up/down to increase or decrease the
r/min value by increments of 200 r/min.
“IND Start” is settable between 6000 -
12800 r/min.
“IND Stop” - the r/min at which the indi-
cator stops flashing can be chosen.
Once selected, rotate the wheel switch
up/down to increase or decrease the
r/min value by increments of 200 r/min.
“IND Stop” is settable between 6200 -
13000 r/min.
“Maintenance”
This module allows you to record the
distance traveled between engine oil
changes (use the OIL item), and for two other items of your choice (use INTER-
VAL 1 and INTERVAL 2).
To reset a maintenance trip meter, se-
lect it and then press and hold the
wheel switch.
TIPMaintenance item names cannot bechanged.
“Unit”
This module allows you to switch the
display between metric and imperial
measurement units.
When using kilometers, the fuel con-
sumption units can be changed be-
tween “km/L” or “L/100km”. When
using miles, MPG will be available.
Temperature units can be switched be-tween Celsius and Fahrenheit.
“Brightness”
This module allows you to adjust the
general brightness level of the display
screen.
Select the desired brightness level by
rotating the wheel switch, and then
press the wheel switch to fix the setting
and return to the top MENU screen.
OIL
INTERVAL 1INTERVAL 2 1000
km/h
km
1000
km
1000
km
Maintenance
km or mile
kmL/100km°C
km/L or L/100km
°C or °F
km/h
Unit
km/h
Brightness
1
BEA-28199-E0.book 18 ページ ２０２１年１２月１日　水曜日　午後７時８分