tow CHEVROLET CAMARO 1967 1.G Chassis Owner's Guide

REAR SUSPENSION
AND
DRIVE LINE
4-19

BRAKE BRAKE

DISC SHOE

OUTER

BEARII
-. -,
-«#*;>•
BRAKE

CAMPER

/

/ /

/ /

si—a

wC—
SPINDLE

^ SUPPOR1

BEARING

^ SPACER

INNER

" BEARING

DRIVE

" FLANGE

BEARING

-PRELOAD

SPACER

DEFLECTOR

CONTROL

ARM

Fig.
46-Wheel Spindle
and
Support Cross-Section (Corvette)

assembly is installed.

d. Pack outer bearing with a high-melting point

wheel bearing lubricant and position on spindle.

Large end of bearing should be toward shoulder

on spindle.

e. Press bearing on spindle using a bearing spacer

and Tool J-9436 as installers, as shown in Fig-

ure 50.

5. Pack spindle inner bearing with a high-melting point

-wheel bearing lubricant and position bearing in

spindle support - small end of bearing should be

positioned inward.

PRESS RAM

BEARING CUP
Fig.
48—Installing Spindle Bearing Cup (Corvette)

Fig.
49—Unseating Drive Spindle Outer Bearing (Corvette)

Fig.
47—Bearing Cup Removal (Corvette)
Fig.
50—Removing and Installing Drive Spindle

Outer Bearing (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-20

Fig.
51—Shock Absorber Installation (Corvette)

6. Tap new spindle inner grease seal into seal bore

and install deflector over support inner end.

Installation

1.
Position support over torque arm bolts with strut

rod fork toward center of vehicle and downward.

Place backing plate over studs and torque nuts to

specifications.

2.
Connect parking brake cable to actuating lever.

3.
Install drive spindle assembly as outlined previously

in this section under "Wheel Bearing Adjustment".

4.
If new spindle support or associated parts are in-

stalled, determine correct shim size as follows.

a. Assemble spindle to support, using a .145" shim.

b.
Check bearing adjustment and correct as neces-

sary, following adjustment procedures previously

outlined.

DIFFERENTIAL CARRIER SUPPORT

BRACKET REPLACEMENT

1.
Place a 1/2" thick block of wood or steel between

nose of differential carrier and floor pan. This will

prevent carrier from twisting upward when support

bracket is disconnected.

2.
Remove carrier support-to-crossmember attaching

bolt.

3.
Remove nut from both of the bracket-to-carrier

through bolts.

4.
Slide bolts to one side until bolt head contacts floor

well. Mark the floor well at this point and drill a

3/4"
diameter hole for each bolt in floor well and

remove bolts.

5. Assemble carrier support bracket by reversing

above procedure. Torque all affected parts to

specifications.

6. Insert plastic plugs from the inside of the floor well

holes to prevent dust and water entry.
STRUT ROD SHAFT STRUT ROD

CAMBER CAM

AND BOLT

Fig.
52—Strut Rods (Corvette)

SHOCK ABSORBER (Fig. 51)

Removal

1.
Disconnect shock absorber upper mounting bolt*

2.
Remove lower mounting nut and lock washer.

3.
Slide shock upper eye out of frame bracket and pull

lower eye and rubber grommets off strut rod mount-

ing shaft.

4.
Inspect grommets and shock absorber upper eye for

excessive wear.

Installation

1.
Slide upper mounting eye into frame mounting

bracket and install bolt, lock washer and nut.

2.
Place rubber grommet, shock lower eye, inboard

grommet, washers and nut over strut rod shaft.

3.
Torque nuts to specifications.

STRUT ROD AND BRACKET (Fig. 52)

Removal

1.
Raise vehicle enough to provide working clearance.

2.
Disconnect shock absorber lower eye from strut

rod shaft.

3.
Remove strut rod shaft cotter pin and nut. With-

draw shaft by pulling toward front of vehicle (fig. 53).

4.
Mark relative position of camber adjusting cam and

Fig.
53-Removing Strut Rod Shaft (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-31

Fig.
77—Differential Pinion Shaft Removal

AXLE SHAFT

Removal

1.
Raise vehicle to desired working height and remove

wheel and tire assembly and brake drum.

2.
Clean all dirt from area of carrier cover. *

3.
Drain lubricant from carrier by removing cover.

4.
Remove the differential pinion shaft lock screw and

the differential pinion shaft (fig. 77).

5. Push flanged end of axle shaft toward center of

vehicle and remove "C" lock from button end of

shaft.

6. Remove axle shaft from housing, being careful not

to damage oil seal.

Wheel Bolt Replacement .

Press bolts out of axle shaft flange (as illustrated in

Figure 78) and press new bolts into place, making sure

that they are tight and square with flange.

Off Seal and/or Bearing Replacement

•1.
Remove the oil seal by using the button end of the

axle shaft - insert the button end of the shaft behind

the steel case of the oil seal, then pry seal out of

bore being careful not to damage housing.

2.
Insert Tool J-8119 into bore and position it behind

bearing so that tangs on tool engage bearing outer

x race. Remove bearing, using slide hammer as shown

in Figure 79. Figure 80 shows a detail of axle

housing outer end.

3.
Lubricate new bearing with wheel bearing lubricant,

and install bearing so that it bottoms against
Fig.
79—Wheel Bearing Removal

shoulder (fig. 81). To install bearing use Tool

J-21491 for the Chevelle, Camaro and Chevy JI

light-duty axle and Tool J-21051 for all Chevrolet

models and also for Chevelle, Camaro and Chevy tl

models with heavy-duty axle.

Pack cavity between the seal lips with a high melting

point wheel bearing lubricant; position seal on tool

(Use J-21491 for the Chevelle, Camaro and Chevy II

light-duty axle and J-21051 for all Chevrolet models

and also for Chevelle, Camaro and Chevy II models

with heavy-duty axle) and position seal in axle

housing bore, tap seal into place so that it bottoms

against bearing (fig. 81).

Brake Flange Plate Replacement

1.
Remove "brake line at wheel cylinder inlet and dis-

assemble brake components from flange plate. Refer

to Section 5 for brake disassembly procedure.

2.
Remove 4 nuts securing flange plate to axle housing.

3.
Install new flange plate to axle housing and torque

nuts to specifications.

Fig.
78—Wheel Bolt Replacement
Fig.
80-Axle Housing Detail

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-32

HP?

Fig.
81
—Whed Bearing and/or Oil Seal Installation

4.
Install brake components on flange and connect

hydraulic line to wheel cylinder inlet. See Section 5

for brake assembly procedure.

5. Install axle shaft, brake drum and wheel and tire

assembly.

6. Bleed and. adjust brakes as outlined in Section 5.

Installation

1.
Slide axle shaft into place.

CAUTION: Exercise care that splines on end

of shaft do not damage oil seal and that they

engage with splines of differential side gear/

2.
Install axle shaft "C" lock on button end of axle-

shaft and push shaft outward so that shaft lock seats

in counterbore of differential side gear.

3.
Position differential pinion shaft through case and

pinions, aligning hole in shaft with lock screw hole.

Install lock screw and torque to specifications.

4.
Using a new gasket, install carrier cover and torque

bolts to specifications.

CAUTION: Make sure both gasket surfaces on

carrier and cover are clean before installing

new gasket. Torque carrier cover bolts in a

crosswise pattern to ensure uniform draw on

cover gasket.

5. Fill axle with lubricant to a level even with bottom

of filler hole. See Section 0 for proper lubricant.

6. Install brake drum and wheel and tire assembly.

7. Lower vehicle and test operation of axle.

PINION FLANGE, DUST DEFLECTOR

AND/OR OIL SEAL

Replacement

1.
Raise rear of vehicle and place stand jacks under

frame side rails so that axle hangs freely to allow

sufficient working room.

2.
Check wheels for freedom of rotation.

3.
Separate rear universal joint, tape trunnion bearings

to joint, position propeller shaft to one side and tie

it to frame side rail.

4.
Using Tool J-5853 with Adapter J-5810 and a suitable

socket on the pinion flange nut, rotate the pinion

through several complete revolutions and record the

torque required to keep the pinion turning (fig. 82).

If flange is to be reused, mark pinion and flange for

reassembly in the same relative position.

5. Install Tool J-8614-1 on pinion flange and remove

pinion flange nut and washer (fig. 83). (Position
Fig. 82—Measuring Drive Pinion Bearing Preload

J-8614-1 on flange so that the four notches are

toward flange.) Discard nut and use a new one

upon reassembly.

6. Thread pilot end of Tool J-8614-3 into small O.D.

end of J-8614-2. Then with J-8614-1 installed as

in Step 4, insert J-8614-2 into J-8614-1 and turn

it 45 degrees to locked position. Remove flange by

turning J-8614-3 while holding J-8614-1 (fig. 84).

7. Pry old seal out of bore, using a screw driver or a

hammer and chisel.

8. Inspect pinion flange for smooth oil seal surface,

worn drive splines, damaged ears, and for smooth-

ness of bearing contact surface. Replace if

necessary.

9. If deflector requires replacement, remove by tapping

from flange, clean up stake points; install new de-

flector, and stake deflector at three new equally

spaced positions.

NOTE:
Staking operation must be performed

in such a manner that the seal operating surface

is not damaged.

1.0. Pack the cavity between the seal lips of the pinion

flange oil seal with a lithium-base extreme pressure

lubricant, position seal in bore, then using Tools

J-21468 and J-9458, for light-duty axle and Tool

Fig. 83-—Drive Pinion Nut Removal

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-34

COMPONENT PARTS REPLACEMENT (CORVETTE)

AXLE DRIVESHAFT-FIGURE 88

Removal

1.
Disconnect inboard driveshaft trunnion from side

gear yoke.

2.
Bend bolt lock tabs down and remove four bolts

securing shaft flange to spindle drive flange.

3.
Pry driveshaft out of outboard drive flange pilot

and remove by withdrawing outboard end first (fig.

89).

Repairs

1.
Remove bearing lock ring from trunnion yoke.

2.
Support turnnion yoke on a piece of 1-1/4" pipe on

arbor press bed.

3.
Using suitable socket or rod, press trunnion down

far enough to drive opposite bearing cup from yoke.

4.
Remove trunnion and press other bearing cup from

yoke, being careful not to
drop'
cup
or lose bearing

rollers.

5. Remove trunnion and yoke from other joint in a

similar manner.

3

AXLE
II 1

i

c

DRI\

c

y
'E SHAFT ^

AXLE
v

DRIVE^
SHAFT
•<i-^""^

Fig.
88—Axle Driveshaft
6. Remove dust seals from trunnion, clean and inspect

bearing rollers and trunnion. Relubricate bearings

with a high-melting point wheel bearing type

lubricant.

NOTE:
In addition to packing the bearings,

make sure that the lubricant reservoir at the

end of each trunnion is completely filled with

lubricant. In filling these reservoirs, pack lu-

bricant into the hole so as to fill from the .

bottom. This will prevent air pockets and en-

sure an adequate supply of lubricant.

7. Place new dust seals on trunnion, cavity of seal

toward end of trunnion - then position Tool J-21556

over end of trunnion and into cavity portion of seal.

Press seal onto trunnion until tool bottoms against

trunnion (fig. 90).

NOTE:
Installation of seal is critical to proper

sealing - use specified tool during installation

to prevent seal distortion and to assure proper

seating of seal on trunnion.

8. Partially install one bearing cup into yoke. Place

trunnion in yoke and into bearing cup. Install other

bearing cup and press both bearing cups into yoke,

being careful to keep trunnion aligned in bearing

cups.

9. Press bearing cups far enough to install lock rings,

and install lock rings.

NOTE:
It may be more convenient, if neces-

sary, to use a bench vise for removal and

installation, instead of an arbor press. In this

case, proceed with disassembly and assembly

procedure as with an arbor press.

Installation

1.
Place driveshaft inboard trunnion into side gear

yokes and assemble
"XJ"
bolts. Rotate yokes so that

trunnion seats are phased 90° apart.

2.
Install outboard drive flange into spindle drive flange

pilot, position bolt lock over bolt holes and install

four bolts. Torque bolts to specification and bend

lock tabs flat against bolt heads.

Fig. 89—Removing Driveshaft

Fig.
90—
"U"
Joint Trunnion Seal Installation

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-36

Fig.
94—Installing Pinion Oil Seal

DIFFERENTIAL CARRIER

Removal

1.
Disconnect spring end link bolts as outlined in

Spring—Removal, in this section.

2.
Disconnect axle drive shafts at carrier by removing

"U"
bolts securing trunnion to side gear yoke.

3.
Disconnect carrier front support bracket at frame

crossmember.

4.
Disconnect propeller shaft at transmission and at

companion flange. Slide transmission yoke forward

into transmission. Drop propeller shaft down and
Fig.
95-Pinion Sea! Installed

out toward the rear.

5. Mark camber cam and bolt relative location on strut

rod bracket and loosen cam bolts.

6. Remove four bolts securing bracket to carrier lower

surface and drop bracket. Remove camber cam bolts

and swing strut rods up and out of the way.

7. Remove eight carrier-to-cover bolts. Loosen bolts

gradually to allow lubricant to drain out.

8. With mounting bolts removed, pull carrier partially

out of cover, drop nose to clear crossmember and

gradually work carrier down and out.

Installation

1.
Clean inside of carrier cover and liberally grease

gasket surface. Place new gasket on cover.

2.
Cut heads off two l/2"-13 x 1-1/4" bolts and slot

unthreaded end. Install these aligning studs into two

below-center carrier bolt holes, one on each side.

3.
Raise carrier into position aligning studs into

cover (fig. 96).

4.
Install carrier-to-cover bolts and tighten securely.

5. Connect propeller shaft to companion flange and

transmission yoke.

6. Install rubber cushion on bracket and position to

frame crossmember. Install hut and torque to

specifications.

7. Raise axle drive shafts into position and assemble

inboard trunnion to side gear yokes with "U" bolts.

8. Assemble strut rods to bracket and raise bracket

into position under carrier. Install four bolts and

torque to specifications. Move camber cams to

marked location and tighten cam nuts.

Fig.
96—Installing Carrier Assembly

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-39

Fig.
103—Removing Bearing Caps

these joints are disassembled, repack bearings

and lubricate reservoir at end of trunnions with

high-melting point wheel bearing lubricant and

replace the dust seals.

1.
Remove bearing lock rings from trunnion yoke.

2.
Support trunnion yoke on a piece of 1-1/4" I.D. pipe

on an arbor bed.

NOTE:
Due to length of the propeller shaft it

may be more convenient to use a bench vise,

for removal and installation, instead of an arbor

press.
In this case, proceed with disassembly

and assembly procedure as with an arbor press.

3.
Using a suitable socket or rod, press trunnion down

far enough to drive bearing cup from yoke (fig. 103).

4.
Remove dust seals from trunnion, clean and inspect

bearing rollers and trunnion. Relubricate bearings

with a lithium base chassis lubricant.

NOTE:
In addition to packing the bearings,

make sure that the lubricant reservoir at the

end of each trunnion is completely filled with

lubricant. In filling these reservoirs, pack lu-

bricant into the hole so as to fill from the

bottom. This will prevent air pockets and ensure

an adequate supply of lubricant.

5. Place new dust seals on trunnions - cavity of seal

toward end of trunnion - then position Tool J-21548
over end of trunnion and into cavity portion of seal.

Press seal onto trunnion until tool bottoms against

trunnion (fig. 104). .

NOTE:
Installation of seal is critical to proper

sealing - use specified tool during installation to

prevent seal distortion and to assure proper

seating of seal on trunnion.

6. Partially install one bearing cup into yoke. Place

trunnion in yoke and into bearing cup. Install other

bearing cup and press both bearing cups into yoke

(fig. 105) being careful to keep trunnion aligned in

bearing cups.

7. Press bearing cups far enough to install lock rings,

and install lock rings.

Installation

1.
Inspect yoke seal in the transmission and replace, if

necessary, as described in the transmission section.

2.
Insert propeller shaft front yoke into transmission.

NOTE:
On Corvette models, install front yoke

into transmission then position propeller shaft

between yoke and companion flange; install "U"

bolts to front yoke.

3.
Align propeller shaft with companion flange, using

reference marks established in "Removal" pro-

cedure, connect the rear universal joint by installing

"U"
bolt clamps over bearing trunnions - torque

nuts to specifications.

Fig.
104—"U" Joint Trunnion Seal installation
Fig.
105—Installing Bearing Cup and Trunnion

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-41

Fig.
109—Bearing Partially Pressed from Propeller Shaft

g. Support exposed trunnion fingers on press bed and

press splined yoke from bearing caps using

method described above,

h. Remove trunnion from splined yoke.

3.
Install trunnion and bearing assembly to the propel-

ler shaft yokes using the,following procedure:

NOTE:
The trunnion and bearing assembly used

at the differential end of the propeller shaft

incorporates two different size bearing caps.

The larger bearing caps (with the annular

grooves) must be mated with the propeller shaft

yoke.

a. Install bearing cap and seal about one-fourth way

in on one side of yoke, using a soft-faced hammer

to tap the bearing into position. Check bearing

cap during installation to ensure that it does not

become cocked in yoke.
Fig.
Ill—Installing Trunnion to Propeller Shaft

b.
Insert trunnion into yoke (fig. 111).

c. Firmly seat trunnion into bearing cup and press

bearing cup into yoke until it is flush with yoke.

d. Install opposite bearing cap and seal making sure

that rollers do not become jammed on trunnion.

Check for free movement of trunnion in yoke.

e. Install bearing retainer snap rings making sure

that gap in ring is toward yoke (fig. 112).

Installation

1.
Inspect yoke seal in the transmission extension, re-

place if necessary as described in the transmission

section.

2.
Insert propeller shaft front yoke into transmission

extension, making sure that output shaft splines

mate with propeller shaft yoke splines.

3.
Align propeller shaft with companion flange using

reference marks established in "Removal" pro-

cedure; remove tape used to retain trunnion bearing

caps;
connect exposed bearing caps to companion

flange by installing retaining strap and screws—

torque screws to specifications.

Fig.
110—Removing Bearing from Propeller Shaft
Fig.
112—Installing Snap Ring to Retain Trunnion

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-6

Fig.
9—Brake Pedal Free Movement

one or two points in appropriate direction, replace

retainer, and re-inspect.

6. Place steel tube connector in hose fitting and tighten

securely.

7. Bleed all brakes as outlined in this section.

8. Do not tighten male end (wheel cylinder end) once

the other end is fixed. If necessary to tighten male

1 end, disconnect hose at opposite end, then reconnect

following above procedure.

Hydraulic Brake Tubing

Hydraulic brake tubing is a double layer annealed

steel terne plate tubing which resists corrosion and has

the physical strength to stand up under the high pr.es-
Fig.
11—Hydraulic Brake Tube Double Flaring Tool

sures which are developed when applying the brakes. In

making up hydraulic brake pipes, it is important that

the proper flaring tool be used to flare the ends of the

tubing for the compression couplings. Unless the tubing

is properly flared, the connections will leak and the

brakes will become ineffective.

CAUTION: When necessary to replace brake

tubing, always use special steel tubing which

is designed to withstand high pressure and re-

sist corrosion. Ordinary copper tubing is not

satisfactory and should not be used.

This safety steel tubing must be double-lap flared at

the ends in order to produce a strong leak-proof joint.

The brake tube flaring. Tool J-8051 (fig. 11) is used to

form the double-lap flare.

Figure 12 shows two pieces of tubing, one with single-

lap flare "A" and the other with double-lap flare "B".

It will be noted that the single-lap flare in "A" split

the tubing while the one shown in "B" is well-formed and

unbroken due to the reinforcement of the double wall.

The following procedure should be followed in making

up hydraulic brake pipes.

Double Lap Flaring

1.
Clamp the tubing in the proper size die blocks with

the flat ends of the blocks toward the end of the

tubing to be cut off. Cut the end of the tubing flush

and square. Using a mill file, dress tubing and

square ends.

Fig.
10-Brake Line Support Bracket

Fig.
12—Single and Double Lap Flaring

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-7

LATCH PLATE

DIE BLOCK

TUBE
UPSET FLARE PUNCH

RAM GUIDE

STOP PLATE

Fig.
13—Flaring Operation--Position ing Tubing

2.
Remove the tubing from the die block and deburr

the inside and outside edges.

3.
Install compression couplings on tubing and dip end

of tubing to be flared in hydraulic fluid. This lubri-

cation results in better formation of the flare.

4.
Place on-half of the die blocks in the tool body with

the counterbored ends toward the ram guide. Now

lay the tubing in the block with approximately 1/2"

protruding beyond the end.

Fit the other half of the block into the tool body,

close the latch plate and tighten the nuts "finger

tight".

5. Select the correct size upset flare punch. One end

of this punch is counterbored or hollowed out to

gauge the amount of tubing necessary to form a

double lap flare. Slip the punch into the tool body

with the gauge end toward the die blocks. Install the

ram; then tap lightly until the punch meets the die

, blocks and they are forced securely against the

stop plate (fig. 13).

6. Using the supplied wrench, draw the latch plate

nut down tight to prevent the tube from slipping.

Tightening the nuts alternately (beginning with the

nut at the closed hole in the plate) will prevent

distortion of the plate. Remove the punch and the

ram. Now reverse the punch and put it back into the

tool body. Install the ram and tap it lightly until

the face of the upset flare punch contacts the face

of the die blocks (fig. 14). This completes the

first operation. Remove the ram and the punch.

7. To complete the flare, insert the pointed finish

flare punch and the ram into the tool body. Tap

the ram until a good seat is formed (fig. 15).

NOTE:
The seat should be inspected at inter-

vals during the finishing operation to avoid

over-seating.

LATCH

DIE BLOCK

TUBE
UPSET FLARE PUNCH
RAM GUIDE

RAM
1ST OPERATION

UPSET FLARE

PUNCH
2ND OPERATION

FINISH FLARE

PUNCH

Fig.
15—Flaring Operation—First and Second Flare

BRAKE ADJUSTMENT

Service Brake

Although the brakes are self-adjusting, a preliminary

or initial adjustment may be necessary after the brakes

have been relined or replaced, or whenever the length

of the adjusting screw has been changed. The final

adjustment is made by using the self-adjusting feature.

1.
With brake drum off, disengage the actuator from

the star wheel and rotate the star wheel by spinning

or turning with a small screw driver.

2.
Recommended

a. Use special Tool J-21177; Drum-to-Brake Shoe

Clearance Gauge, to check the diameter of the

brake drum inner surface (fig. 16).

Fig.
14—Flaring Operation—First Flare
Fig.
16—Using Drum-to-Brake Shoe Clearance

Gauge Tool J-21177

CHEVROLET CHASSIS SERVICE MANUAL