tow CHEVROLET CAMARO 1967 1.G Chassis Repair Manual

CLUTCH AND TRANSMISSIONS 7-10 ,

GENERAL DESCRIPTION

The overdrive unit is essentially a two-speed planetary-

transmission attached to the rear of a conventional three-

speed transmission. In overdrive, engine speed is ap-

proximately 30 per cent slower at a given road speed

since the drive train includes planetary gears which pro-

vide a lower overall gear ratio than that obtained in high

gear with the conventional transmission.

The electrical equipment which controls the automatic

action of the mechanical portion of the overdrive unit

consists of a solenoid, a speed-sensitive governor switch,

a relay and a kickdown switch. The circuit including this

equipment makes it possible to operate in overdrive above

a pre-set cut-in speed, or in .conventional drive at any

speed.

With the overdrive unit engaged, the transmission

should not be left in any forward gear with intent of lock-

ing the drive-line as the overrunning clutch is a free-

wheeling condition.
SERVICING THE OVERDRIVE

With the,overdrive assembly removed from the trans-

mission, service operations on the transmission proper

are the same as for the standard three-speed trans-

mission.

Repairs to the overdrive housing, output shaft, ring

gear assembly, clutch cam, roller retainer, pinion cage,

sun gear, shift rail, sun gear control plate, output shaft

bearing, oil seal, speedometer drive gear, solenoid pawl

and interlock plunger may be performed underneath the

car, if so desired, by removing the overdrive housing

without disturbing the transmission. Refer to Overhaul

Manual for Service Procedure.

If the transmission mainshaft, overdrive adapter or

transmission rear bearing which is retained in adapter

require replacement, the entire transmission and over-

drive assembly should be removed and overhauled on the

bench.

MAINTENANCE AND ADJUSTMENTS

Servicing of the overdrive governor switch and pinion,

the sun gear solenoid, oil seal and cable bracket, the out-

put shaft rear oil seal, the control shaft lever, and the

speedometer driven gear may be accomplished without

removing the overdrive from the vehicle, as discussed

in the following paragraphs:

GOVERNOR SWITCH AND PINION

To remove governor switch, disconnect wires at gover-

nor switch and screw governor
out
of housing, using Tool

J-4653 on the flat hexagonal surface of governor case.

The pinion may be separated from the governor by re-

moving the snap ring on the shaft.

SUN GEAR SOLENOID, OIL SEAL AND

CONTROL CABLE BRACKET

Remove the solenoid by taking out the two mounting

bolts and lock washers, removing
the.
cable bracket with

the lower bolt. Turn the solenoid 1/4 turn and
pull,
sole-

noid plunger out of adapter. The oil seal may be pried

out of the adapter.

CASE REAR OIL SEAL

Removal

1.
Remove propeller shaft as outlined in Section 4.

2.
Using a punch against seal in housing, pry out seal

from housing.

Installation

1.
Prelubricate between sealing lips and coat outside of

new oil seal with a suitable sealant, then start seal

into bore in overdrive housing.

2.
Using Tool J-5154 drive oil seal into counterbore.

3.
Install propeller shaft as outlined in Section 4.

CONTROL SHAFT LEVER AND/OR "O" RING

OIL SEALS

To remove- the control shaft, disconnect the cpntrol
cable, remove tapered pin and pull lever out. Replace

the two "0" ring seals on the control shaft. Insert shaft

and new "O" ring seals into housing and install tapered

pin. Connect control wire to lever.

SPEEDOMETER DRIVEN GEAR

Disconnect speedometer cable, remove lock plate to

housing bolt and lock washer and remove lock plate. In-

sert screw driver in lock plate slot in fitting and pry

fitting, gear and shaft from housing. Pry "O" ring from

groove in guide.

Install new "O" ring in groove in fitting and insert

shaft.

Hold the assembly so slot in fitting is toward lock plate

boss on housing and install in housing. Push fitting into

housing until lock plate can be inserted in groove and

attached to housing.

L
dl

ZAIR GAP

km (CHECK WITH

M*= POINTS BARELY
'A

AoWER
|^

POINT

0 ADJUST

=^ i
SUPPORT

Fig. IB - Checking Relay Air Gap

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-15

LOCATING

GAGE B

N

Fig.
1C - Warner T-16 3-Speed Lever and Linkage Adjustment (Camaro and Corvette)

Clearance should be .002 to .008. Interlock sleeves

are available in four sizes to give the proper

clearance.

6. Install outer shifter levers to shafts with lock wash-

ers and nuts. Tighten securely. v

7.
Instill shifting forks to shift levers (1st and re-

verse fork "hump" towards bottom).

Installation

1.
Install new side cover gasket to transmission case,

install cover and secure with lock washers and cap

screws.

NOTE: The two rear side cover to case at-

taching bolts have a special oil sealing spline

and must be used at these two "through" hole

locations.

2.
Connect control rod and cross shaft to control

levers.

1.
Side Cover

2.
Poppet

3. 1st and Reverse Shifter

Lever and Shaft

4.
Poppet Spring

5. 1st and Reverse Shifter

Fork
6. Interlock Pin

7. 2nd and 3rd Shifting

Fork

8. Interlock Sleeve

9. 2nd and 3rd Shifter

Lever and Shaft

10.
"O11 Ring Seal

Fig.
2C - Side Cover Assembly - Layout

CHEVROLET CHASSIS SERVICE MANUAl

CLUTCH AND TRANSMISSIONS 7-19

2.
With handle in full down position—adjust cable to ac-

quire dimension shown, be certain that cable is pulled

taut.

3.
Tighten set screw to 15-20 in. lbs.

4.
Bend excess wire and cut - be certain that wire does

not interfere with I.D. of lever or threads of shifter

knob.

NOTE: Handle must return freely from any

position.

SPEEDOMETER DRIVEN GEAR AND OIL SEAL

Replacement

Disconnect speedometer cable, remove retainer to

housing bolt and lock washer and remove retainer. In-

sert screw driver in slot in fitting and pry fitting, gear

and shaft from housing. Pry "O" ring in groove in fitting.

Install new "O" ring in groove and insert shaft Hold

the assembly so slot in fitting is toward boss on housing

and install in housing. Push fitting into housing until re-

tainer can be inserted in groove and install retainer lock

washer and bolt.
Fig.
5M - Installing Side Cover Assembly

TRANSMISSION SIDE COVER

Removal

1.
Disconnect control rods from levers.

2.
Shift transmission into second speed before removing

cover, by moving 1-2 (Rear Cover) shifter lever into

forward detent position.

3.
Remove cover assembly -from transmission case

carefully and allow oil to drain.

Disassembly (Fig. 4M)

1.
Remove the outer shifter lever nuts,*lock washers

and flat washers. Pull levers from shafts.

2.
Remove both shift forks from shifter shaft and detent

plate assemblies. Remove both shifter shaft assem-

blies from cover. Lip seals in side cover may now

be pryed out if replacement is required because of

damage.

1-2 DETENT CAM DETENT SPRING
3-4 DETENT CAM

1-2 SHIFTER SHAFT

1-2 SHIFT FORK
3-4 SHIFT

FORK

DETENT CAM \ 3-4 SHIFTER SHAFT

RETAINER RING

DETENT CAM PIVOT PIN
3.
Remove detent cam spring and pivot retainer "C"

ring. Remove both detent cams.

4.
Replace necessary parts.

Assembly (Fig. 4M)

1.
Install 1-2 detent cam to cover pivot pin first, then

install 3-4 detent cam so the detent spring notches

are offset or opposite each other. Detent cam

notches must be facing downward.

2.
Install detent cam retaining "C" ring to pivot shaft,

and hook spring into detent cam notches.

3.
Install both shifter shaft assemblies in cover being

careful not to damage lip seals. Install both shift

forks to detent plates, lifting up on detent cam to

allow forks to fully seat into position.

4.
Install outer shifter levers, flat washers, lock wash-

ers and nuts.

Installation (Fig. 5M)

1.
Shift 1-2 shifter lever into second speed (forward)

position. Position cover gasket on case.

2.
Carefully position side cover into place making sure

the shift forks are aligned with their respective

mainshaft clutch sliding sleeves.

3.
Install cover attaching bolts and tighten evenly to

15-20 ft. lbs. torque.

4.
Remove filler plug and add lubricant specified in

Section 0, to level of filler plug hole.

EXTENSION OIL SEAL

Replacement

1.
Remove propeller shaft.

2.
Pry out the extension oil seal.

3.
Prelubricate between sealing lips and press new oil

seal carefully into place in extension using J-5154 or

similar tool.

Fig.
4M - Transmission Side Cover/ Shift Fork and

Detent Assembly
CAUTION: Do not excessively force the seal

against the seat in the extension.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-24

is at the full mark on the dip stick, it is just slightly be-

low the planetary gear unit. If additional oil is added,

bringing the oil level above the full mark, the planetary

unit will run in the oil, foaming and aerating the oil. This

aerated oil carried through the various oil pressure pas-

sages (low servo, reverse servo, clutch apply, converter,

etc.) may cause malfunction of the transmission assem-

bly, resulting in cavitation noise in the converter and

improper band or clutch application. Overheating may

also occur.

If the transmission is found consistently low on oil, a

thorough inspection should be made to find and correct

all external oil leaks.

PERIODIC OIL CHANGE

The transmission oil should be changed periodically as

recommended in Section 0, and whenever transmission is

to be removed from the vehicle for repairs.

1.
Run engine for one minute in neutral prior to chang-

ing.

2.
Be sure vehicle is level or raise from the rear only.

3.
Remove the oil pan drain plug and allow oil to drain

thoroughly into a pan or can.

Replace drain plug and refill with approximately two

quarts of oil specified in Section 0.

NOTE: To refill the transmission, remove dip

stick from oil filler tube and refill transmission

with oil specified in Section 0 using filler tube

and funnel J-4264. Then, after shifting into all

ranges at idle speed to fill all oil passages, the

engine should be run at 800-1000 rpm with the

transmission in Neutral until the oil warms up,

then add oil as required to raise the fluid level

to the full mark on the dip stick. Refill capacity

is approximately 2 qts.
4.

Fig.
1PG - Adjusting Low Band Using J-21848
PERIODIC LOW BAND ADJUSTMENT (Fig. 1PG)

Low band adjustment should be periodically performed

at 12,000 mile intervals, or sooner, as necessary if op-

erating performance indicates low band slippage.

1.
Raise vehicle and place selector lever in neutral.

2.
Remove protective cap from transmission adjusting

screw.

3.
a. On Corvette Models: Drop left exhaust pipe for

clearance.

b.
On Chevelle Models: To gain clearance between

underbody and transmission, it may be necessary

to remove rear mount bolts from crossmember,

and move transmission slightly toward passenger

side of vehicle. .

4.
Loosen adjusting screw lock nut 1/4 turn and hold in

this position with wrench.

5.
Using Special Tool J-21848 adjust band to 70 in. lbs.

and back off four (4) complete turns for a band which

has been in operation for 6,000 miles or more,.or

three (3) turns for one in use less than 6,000 miles.

CAUTION: Be sure to hold the adjusting screw

lock nut at 1/4 turn loose with a wrench during"

the.adjusting procedure.

6. Tighten the adjusting screw lock nut to specified

torque.

CAUTION: The amount of back-off is not an

approximate figure, it must be exact.

MANUAL SHIFT LINKAGE CHECK & ADJUST

(Column Type)

1.
The shift tube and lever assembly must be free in the

mast jacket. See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift

the transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selected lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now

be inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent, and

the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

7.
In the event that an adjustment is required, place

the selector lever in drive (D) position as determined

by the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft,

and rotate the transmission lever so that it contacts

the drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

2 and 6.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-33

from rolling. The pointer on the indicator quadrant

should line up properly with the range indicators in all

ranges.

OIL LEAKS

Before attempting to correct an oil leak, the actual

source of the leak must be determined. In many cases

the source of the leak can be deceiving due to "wind flow1 f

around the engine and transmission.

The suspected area should be wiped clean of all oil

before inspecting for the source of the leak. Red dye is

used in the transmission oil at the assembly plant and

will indicate if the oil leak is from the transmission.

The use of a "black light"* to identify the oil at the

source of leak is also helpful. Comparing the oil from

the leak to that on the engine or transmission dip stick

(when viewed by black light) will determine the source

of the leak.

Oil leaks around the engine and transmission are gen-

erally carried toward the rear of the car by the air

stream. For example, a transmission "oil filter tube

to case leak" will sometimes appear as a leak at the

rear of the transmission. In determining the source of

an oil leak it is most helpful to keep the engine running.

The mating surfaces of servo cover, converter housing,

transmission case and transmission case extension

should be carefully examined for signs of leakage. The

vacuum modulator must also be checked to insure that

the diaphragm has not ruptured as this would allow trans-

mission oil to be drawn into the intake manifold. Us-

ually, the exhaust will be excessively smoky if the

diaphragm ruptures due to the transmission oil added to

the combustion. The transmission case extension rear

oil seal should also be checked. All test plugs should be

checked to make sure that they are tight and that there

is no sign of leakage at these points. The converter

underpan should also be removed. Any appreciable quan-

tity of oil in this area would indicate leakage at the pump

square seal ring, pump seal assembly, or pump bolt

sealing washers.

BASIC PRESSURE CHECKS

Four basic pressure checks are used for diagnosis and

operational checks for the Aluminum Powerglide trans-

mission. All checks should be made only after thoroughly

warming up the transmission.

• Wide Open Throttle Upshift Pressure.

• Idle Pressure in "Drive" Range.

• Manual "Low" Range Pressure.

• "Drive" Range Overrun (Coast) Pressure.

It is not recommended that stall tests be conducted

which would result in engine vacuum falling below 10" Hg.

Pressure gauge hose connections should be made at

the low servo apply (main line) test point (fig. 14PG).

Run the gauge line into the driving compartment by

pushing aside the mast jacket seal. The line out of the

way of the drivers feet and connect to pressure gauge

J-21867.

• Wide Open Throttle Upshift Pressure Check

Refer to the pressure check chart for upshift pressure
SERVO APPLY

PRESSURE

Fig.
14PG - Pressure Test Plug

points as indicated on the lower servo apply (main line)

gauge.

• Idle Pressure in "Drive" Range

In addition tp the oil pressure gauges, a vacuum gauge

is needed for this check.

With the parking brake applied and the shift selector

lever in "Drive", low servo apply (main line) pressure

should be as shown on the pressure check chart.

If pressures are not within these ranges, the following

items should be checked for oil circuit leakage:

1.
Pressure regulator valve stuck.

2.
Vacuum modulator valve stuck.

3.
Hydraulic modulator valve stuck.

4.
Leak at low servo piston ring (between ring and

bore).

5.
Leak at low servo piston rod (between rod and bore).

6. Leak at valve body to case gasket.

7.
Leak at valve body gaskets.

8. Front pump clearances.

9. Check passages in transmission case for porosity.

• Manual "Low" Range Pressure Check

Connect a tachometer, apply the parking brake, place

the selector lever in "Low" range, and adjust the engine

speed to 1000 rpm with the car stationary.

Low servo apply (main line) pressure should be as

shown on the pressure check chart.

Pressures not within this range can indicate the fol-

lowing possibilities:

1.
Partially plugged oil suction screen.

2.
Broken or damaged ring low servo.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-37

LI.
- LI Range can be selected at any vehicle speed,

and the transmission will shift to second gear

and remain in second until vehicle speed is re-

duced to approximately 40 MPH, .depending on

axle ratio. LI Range position prevents the trans-

mission from shifting out of first gear.
It is very important that any communication concerning

the Turbo Hydra-Matic always contain the transmission

serial number and that all transmission parts returned

to Chevrolet Motor Division always be tagged with the

transmission serial number.

MAINTENANCE AND ADJUSTMENTS

TRANSMISSION FLUID

Transmission fluid level should be checked with trans-

mission warm and selector lever in "P" Park position,

every time engine oil level is checked or as specified in

Section 0 when engine oil is changed.

CAUTION: Since the Turbo Hydra-Matic trans-

mission is very sensitive to oil level, special

precautions should be taken when checking the

oil level, to insure against an overfifE

Transmission fluid should be changed as specified in

Section 0.

FLUID LEVEL INDICATOR

The fluid level indicator is located in the filler pipe at

the right rear corner of the engine. To bring the fluid

level from the add mark to the full mark add 1 pint.

Fluid level should be to the full mark with transmission

at normal operating temperature. With cold fluid the

level should be at the add mark or slightly below.

SHIFT CONTROL LINKAGE ADJUSTMENT

Adjust linkage as shown below and in Figure 2.

1.
The shift tube and lever assembly must be free in the

mast jacket See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift the

transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selector lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now be

inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent,

and the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

See schematic diagram.

7.
In the event that an adjustment is required, place the

selector lever in drive (D) position as determined by

the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft, and
rotate the transmission lever so that it contacts the

drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

Steps 2 and 6. -

l(h Readjust indicator needle if necessary to agree with

the transmission detent" positions. See Section 9.

11.
Readjust neutral safety switch if necessary to pro-

vide the correct relationship to the transmission de-

tent positions. See Section 12.

12.
When properly adjusted the following conditions must

be met by manual operation of the steering column

shift lever:

a. From reverse to drive position travel, the trans-

mission detent feel must be noted and related to

indicated position on dial.

b.
When in drive and reverse positions, pull lever

rearward (towards steering wheel) and then re-

lease. It must drop back into position with no

restrictions.

NEUTRAL SAFETY SWITCH ADJUSTMENT

The neutral safety switch must be adjusted so that the

car will start in the park or neutral position, but will not

start in the other positions. For replacement refer to

Section 12 of this Manual.

DRAINING AND REFILLING TRANSMISSION

Drain oil immediately after operation before it has had

an opportunity to cool.

To drain oil proceed as follows:

1.
Remove bottom pan attaching screws, pan, and gas-

ket.

2.
Remove oil strainer. Remove "O" ring seal from

pick-up pipe and discard.

3.
Discard strainer if dirty.

4.
Install new "O" ring seal on pick-up pipe and install

strainer and pipe assembly.

5.
Thoroughly clean bottom pan.

6.. Affix new gasket to bottom pan with petroleum jelly.

7.
Install bottom pan with attaching screws and torque

to specifications;

8. If only the pan has been removed, pour approximately

7-1/2 pints of fluid into the transmission. If the

valve body has also been removed use 9-1/2 pints.

After a complete overhaul approximately 19 pints

are required. Be sure container, spout, or funnel is

clean.

9. Start engine and let idle (carburetor off fast idle

step).
Place selector lever in P position and apply

hand brake.

10.
With transmission warm (approximately 150°F), add

fluid to bring level to full mark on indicator.

CAUTION: Do not overfill. Foaming will re-

sult.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-41

CAUTION: Use converter holding ToolJ-5384

when lowering transmission or keep rear of

transmission lower than front so as not to lose
converter.

The installation of the transmission is the reverse of

the removal.

TURBO HYDRA-MATIC DIAGNOSIS PROCEDURE

Accurate diagnosis of transmission problems begins

with a thorough understanding of normal transmission

operation. In particular, knowing which units are in-

volved in the various speeds or shifts so that the specific

units or circuits involved in the problem can be isolated

and investigated further. Analytical diagnosis will pro-

tect the technician from come backs and certainly will

improve owner satisfaction.

An important and often overlooked aspect of diagnosis

is finding out specifically what the customer is com-

plaining of. For this purpose a short ride with the cus-

tomer will often prove beneficial. It may be found that

the condition the customer wants corrected is standard

and should not be altered.

The following sequence, based on field experience, pro-

vides the desired information quickly and in most cases

actually corrects the malfunction without requiring the

removal of the transmission. Details of the items listed

in this sequence are covered further in the text.

SEQUENCE FOR TURBO HYDRA-MATIC

DIAGNOSIS PROCEDURE

1.
Check oil level and condition.

2.
Check and correct detent switch.

3.
Check and correct vacuum line and fittings.

4.
Check and correct manual linkage.

OIL LEVEL AND CONDITION CHECK

Always check the oil level before road testing. Oil

must be visible on dip stick prior to operating the ve-

hicle. Erratic shifting, pump noise, or other malfunc-

tions can in some cases be traced to improper oil level.

Oil level should be checked with the selector lever in

the Park (P) position, engine running, and the vehicle on

level pavement.

Fluid level should be to the FULL mark with the trans-

mission at normal operating temperature (170°-190°
F.).

With warm fluid (room temperature), the level should be

at or slightly below the ADD mark.

If oil level was low, refer to Oil Leaks.

The condition of the oil is often an indication of whether

the transmission should be removed from the vehicle, or

to make further tests. When checking oil level, a burned

smell and discoloration indicate burned clutches or bands

and the transmission will have to be removed.

MANUAL LINKAGE

Manual linkage adjustment and the associated neutral

safety switch are important from a safety standpoint

The neutral safety switch should be adjusted so that the

engine will start in the Park and Neutral positions only.

With the selector lever in the Park position, the park-

ing pawl should freely engage and prevent the vehicle

from rolling. The pointer on the indicator quadrant

should line up properly with the range indicators in all

ranges.
OIL LEAKS

Before attempting to correct an oil leak, the actual

source of the leak must be determined. In many cases,

the source of the leak can be deceiving due to "wind flow"

around the engine and transmission.

The suspected area should be wiped clean of all oil be-

fore inspecting for the source of the leak. Red dye is

used in the transmission oil at the assembly plant and

will indicate if the oil leak is from the transmission.

. The use of a "black light"* to identify the oil at the

source of leak is also helpful. Comparing the oil from

the leak to that on the engine or transmission dip stick

(when viewed by black light) will determine the source

of the leak.

Oil leaks around the engine and transmission are gen-

erally carried toward the rear of the car by the air

stream. For example, a transmission "oil filler tube to

case leak" will sometimes appear as a leak at the rear of

the transmission. In determining the source of an oil

leak it is most helpful to keep the engine running.

POSSIBLE POINTS OF OIL LEAKS

• 1. TRANSMISSION OIL PAN LEAK

a. Attaching bolts not correctly torqued.

b.
Improperly installed or damaged pan gasket.

c. Oil pan gasket mounting face not flat.

2.
REAR EXTENSION LEAK

a. Attaching bolts not correctly torqued.

b.
Rear seal assembly — damaged or improperly

installed.

c. Gasket seal — (extension to case) damaged or

improperly installed.

d. Porous casting.

3.
CASE LEAK

a. Filler pipe "O" ring seal damaged or missing;

misposition of filler pipe bracket to engine —

"loading" one side of
"O"
ring.

b.
Modulator assembly "O" ring seal
—
damaged or

improperly installed.

c. Governor cover, gasket and bolts — damaged,

loose; case face leak.

d. Speedo gear
—
"O" ring damaged.

e. Manual shaft seal — damaged, improperly in-

stalled.

f. line pressure tap plug — stripped, shy sealer

compound.

g. Parking pawl shaft cup plug
—
damaged, improp-

erly installed.

h. Vent pipe (refer to Item 5).

i. Porous case.

4.
FRONT END LEAK

a. Front seal - damaged (check converter neck for

nicks,
etc., also for pump bushing moved for-

ward);
garter spring missing from pump to con-

verter seaL

b.
Pump attaching bolts and seals
—
damaged, miss-

ing, bolts loose.

CHEVROLET a
SERVICE

FUEL TANK AND EXHAUST SYSTEMS 8-2

COMPONENT PART REPLACEMENT

FUEL TANK

Draining Tank

The absence of a drain plug in the gas tanks makes it

necessary to siphon fuel from the tank when draining is

needed. The following procedure is recommended.

1.
Obtain approximately 10 feet of 3/8" I.D. hose and

cut a flat-type slit 18" from one end. Make this cut

on the hose in the direction "toward the shorter end

(See Figure 2).

2.
Insert a small pipe nipple (slightly larger O.D. than

the hose I.D.) into the opposite end of hose.

3.
Insert the nipple end of the siphon hose into the fuel

tank filler neck with the natural curl of the hose

pointing down. Insert until the hose is heard to strike

bottom of the tank.

4.
With the opposite end of the hose in a suitable con-

taner insert an air hose in downward direction in the

flap-type slit and trigger the flow of fuel.
FUEL FLOW

-If*
APPROX.-1 >SUT «<>«
AS SHOWN

10 FEET APPROX.-

Fig. 2—Siphon Construction

FWD
V-8

VIEW B

Fig. 3-Fuel Lines

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-19

Fig.
22—Spare Tire Carrier Installed

6. Remove two fuel tank retaining strap bottom nuts

from forward support member located at forward

front side of tank.

7. Remove fuel tank metering unit wires (fig. 25).

8. Remove fuel pickup line and drain tank.

9. Remove gas cap, filler neck boot from the top of tank

and disconnect drain line (fig. 24).

NOTE:6
Coupe Models—Remove filler neck.

10.
Remove fuel tank support frame attachment bolts and

support.

11.
Lower tank and rotate toward the front of vehicle.

Installation (20 Gallon Tank)

NOTE:
Place hoses and wires to one side and

position anti-squeak pads to the crossmember,
END OF HOSE FLUSH

TO Va INCH BACK FROM

EDGE OF BUMPERETTE

Fig.
24-Gas Tank Filler Neck Vent Hose

cemented to the support and attached to the tank.

Replace with new pads as required.

1.
Hook retaining straps at the rear frame crossmem-

ber. (Crimp strap ends at rear frame attachment.)

NOTE:
Make certain strap ends are hooked and

anti-squeak pads are properly positioned.

2.
Slowly rotate fuel tank into position.

CAUTION: Coupe-Install filler neck after tank

is installed.

3.
Attach fuel tank support at the frame side rails.

TANK METERING UNI

WIRE CONNECTIONS

Fig.
23—Exhaust System Tail Pipe Attachment
Fig.
25—Fuel Tank Metering Unit, Wires and Lines

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-25

4.
Cut the exhaust pipe near the muffler (see cau-

tion above) to allow sufficient pipe for muffler

replacement.

5.
^
Replace muffler and secure with new clamps.

NOTE:
Clamps must be assembled with nuts

attached toward the rear of the vehicle -

reference 90° to sawcuts in service muffler

pipe.

6. Reverse procedure for installation.

NOTE:
If bracket mounting insulators (tire

carcass mountings) are fatigued, replace to in-

sure a secure exhaust system.
7. In the event the tail pipe bezel has been damaged and

replacement is required, remove three screws and

replace the bezel. i

SIDE MOUNTED EXHAUST (Fig. 31)

Replacement

1.
Raise and support vehicle.

2.
Remove sill molding attaching screws and disengage

molding from the retainer.

3.
Remove cover retaining screws, cover and retainer

assembly.

4.
Remove exhaust pipe-to-manifold attaching nuts, and

rear bracket retaining nut, then detach exhaust pipe

from manifold studs and remove from vehicle.

Fig.
31—Side Mounted Exhaust System

CHEVROLET
CHASSIS SEKVK