DODGE RAM SRT-10 2006 Service Repair Manual

INSTALLATION
FRONT HOSES
1. Position the lower portion through the grommet in
the body (3).
2. Connect the new drain tube to the sunroof housing
(1) and test drainage.
3. Position the tube support clips (2) and seat fully.
4. Install headliner (Refer to 23 - BODY/INTERIOR/
HEADLINER - INSTALLATION).
REAR HOUSING HOSE
1. Install the rear tube and seat the push pin fasten-
ers (2) fully. * Front tube shown, rear similar.
2. Position the lower portion through the grommet in
the body (3).
3. Connect the new drain tube to the sunroof housing
(1) and test drainage.
4. Install headliner (Refer to 23 - BODY/INTERIOR/
HEADLINER - INSTALLATION).

MOTOR
DESCRIPTION
For service information refer to (Refer to 8 - ELECTRICAL/POWER TOP/MOTOR- DIAGNOSIS AND TESTING).

SUNSHADE
REMOVAL
1. Remove the drain channel. (Refer to 23 - BODY/
SUNROOF/CHANNEL-DRAIN - REMOVAL)
2. Push up the front center of the sunshade (1) to pop
out the front two feet.
3. Rotate the sunshade (2) so that the other feet (1)
are removed from the guide track.

INSTALLATION
1. Verify the sunshade track is free of obstructions
like the trim lace/ring.
2. Start with sunshade (2) at an angle with one foot
(1) in the track.
3. Rotate the sunshade so the other rear foot is in the
track as well as the 2 other feet (3) on the same
side as the first foot.
4. To insert the remaining two feet (2) apply force to
the middle front of sunshade (3) and guide them
into the track.
5. Check that all the feet are in the right track and
verify sunshade operation.
6. Install the drain channel. (Refer to 23 - BODY/
SUNROOF/CHANNEL-DRAIN - INSTALLATION)

SWITCH-SUNROOF
DESCRIPTION
For service information refer to (Refer to 8 - ELECTRICAL/POWER TOP/SWITCH - DIAGNOSIS AND TESTING).

TRIM RING
REMOVAL
1. Remove the headliner. (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL)
2. Remove the 12 nuts (1) and roll the trim ring off the
headliner off the retaining flanges (2).
INSTALLATION
1. Position trim ring support flanges (2) over the
headliner and seat the trim ring fully.
2. Install the 12 nuts (1) onto the support studs.

page page
A-PILLAR WEATHERSTRIP RETAINER
REMOVAL ................................... 301
INSTALLATION .............................. 301
DRIP RAIL WEATHERSTRIP
REMOVAL ................................... 302
INSTALLATION .............................. 302
DOOR OPENING SEAL
REMOVAL ................................... 303
INSTALLATION .............................. 306
DRIP RAIL WEATHERSTRIP RETAINER
REMOVAL ................................... 310
INSTALLATION .............................. 310
FRONT DOOR GLASS RUN WEATHERSTRIP
REMOVAL ................................... 311
INSTALLATION .............................. 312FRONT DOOR OUTER BELT MOLDING
REMOVAL ................................... 313
INSTALLATION .............................. 313
FRONT DOOR INNER BELT MOLDING
REMOVAL ................................... 314
INSTALLATION .............................. 314
REAR DOOR GLASS RUN WEATHERSTRIP
REMOVAL ................................... 316
INSTALLATION .............................. 316
REAR DOOR OUTER BELT MOLDING
REMOVAL ................................... 317
INSTALLATION .............................. 317
REAR DOOR INNER BELT MOLDING
REMOVAL ................................... 318
INSTALLATION .............................. 318

A-PILLAR WEATHERSTRIP RETAINER
REMOVAL
1. Remove the drip rail weatherstrip retainer (1)
(Refer to 23 - BODY/WEATHERSTRIP/SEALS/
DRIP RAIL WEATHERSTRIP - REMOVAL).
2. Remove the five screws (8) and remove the A-pillar
weatherstrip retainer (7).
INSTALLATION
1. Install the A-pillar weatherstrip retainer (7) and
install the screws (8).
2. Install the drip rail weatherstrip retainer (1) (Refer
to 23 - BODY/WEATHERSTRIP/SEALS/DRIP RAIL
WEATHERSTRIP - INSTALLATION).

DRIP RAIL WEATHERSTRIP
REMOVAL
1. Open the doors and separate the weatherstrip (3)
from the drip rail and a-pillar retainers (1 and 7).
INSTALLATION
1. Position the weatherstrip (3) onto the drip rail and
a-pillar retainers (1 and 7) and seat fully.

DOOR OPENING SEAL
REMOVAL
FRONT DOOR SEAL
1. Remove the cowl trim panel (1) (Refer to 23 -
BODY/INTERIOR/COWL TRIM - REMOVAL).
2. If vehicle is aStandard Cab, remove the lower
b-pillar trim panel (3) (Refer to 23 - BODY/INTERI-
OR/B-PILLAR LOWER TRIM - REMOVAL).