vi number JAGUAR X308 1998 2.G Workshop Manual

Throttle Position (TP) Sensor
Location

P
arts List
sen
d
s the ECM a signal indica
ting throttle plate angle
is
the main input to the ECM from the driver
i
s
a dual Hall effect devi
ce mounted on the motor en d of the throttle body
Two additional sensors are attached to the throttle body to provide additional feedback to the ECM: a mechanical guard
position sensor and an accelerator pedal position sensor.
Cam s
haft Position (CMP) Sensor
sen
d
s the ECM a signal indicating camshaft po
sition for fuel synchronization purposes
is
a variable reluctance device mounted on bank 2 cylinder side face
generates a signal when the ri
ng
fitted to the bank 2 inlet
camshaft passes the sensor
Cranksha
ft Position (CKP) Sensor
i
s
a variable reluctance device
mounted on the engine oil pan
Ite
m
Par
t
Number
De
scr
iption
1—Acce
le
rator pedal and mechanic
al guard position sensors
2—Throttle
(blade)
position sensor

P
arts List
It

em
Par
t Number
De
scription
1—PI032

VVT solenoid 2
2—PI027

KS 2
3—PI004

ECT sensor
4—PI026

KS 1
5—PI031

VVT solenoid 1
6—PI035

MAFS (on vehicle)
7—PI050

Generator
8—PI040

Oil pressure switch
9—PI018

to PI021 Bank 1 Ignition coils 1 to 4
PI022 to PI025 Bank 2 Ignition coils 1 to 4
10—PI006
Throttle valve position sensor
11—PI002 En

gine management harness (on vehicle)
12—PI001 En

gine management harness (on vehicle)
13—PI033

Throttle valve motor
14—PI034

EGR valve (where fitted)
15—PI015 CM

P sensor
16—PI042

Accelerator pedal and
mechanical guard sensors
17—PI007
to PI010 Bank 1 Injectors 1 to 4 PI011 to PI014 Bank 2 Injectors 1 to 4
18—PI037

Compressor lock
sensor (where fitted)
19—PI036
Compressor clutch
20—PI017 CK

P sensor
E
ngine Harness Connectors
Location

Ite
m
Par
t
Number
De
scr
iption
1—Engine

management fuse box
2—Engine
control module (E
CM)
Circuit Diagrams (extracts only)
ECM Su
pply Voltage

Ite
m
Part
Number
Descr
iption
1—Knock
sensors, banks 1 and 2

2—Engine
control module (E
CM)
Knock
Sensor

It
em
Par
t Number
De
scription
1—Cranksh

aft position sensor
2—Engine

control module (ECM)
Crankshaft Posi
tion sensor

Ite
m
Par
t
Number
De
scr
iption
1—Camshaft position

sensor
2—Engine
control module (E
CM)
Cams
haft
Position sensor

It
em
Par
t Number
De
scription
1—MAF

assembly
2—MAF s

ensor
3—IAT se

nsor
4—Engi

ne to vehicle harness connector
5—EMS fuse box


6—Engine

control module (ECM)
7—Charge air cool

er -
IAT sensor (superchar
ged engin
es only)

MAF
and IAT Sensors

CAUTIO
N: When probing connectors to take
measurements in the course of the pinpoint tests, use the adaptor kit,
part number 3548-1358-00.
• NOTE: When performing electrical voltag e or resistance tests, always use a digital multimeter (DMM) accurate to 3
decimal places, and with an up-t o-date calibration certificate. When testing resistance, always take the resistance of the
DMM leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic ro utines involving pinpoint tests.
Sym
ptom Chart
Sym

ptom
(general)
S y
mptom (specific)
Possib
l
e source
Acti
o
n
No
n
-Start
Engine
does not cran
k
Starter relay ECM relay Batt
ery Park
/Neutral
switch
Starting system

Harness damage
Engine s
iezed
Check r
e
lay dates. Check
for DTCS. For starting
system,
REFER to Section 303
-06 Sta r
ting System
.
F or ECM
relay tests, GO to Pinpoint Test
AD.
.
F o
r battery information,
REFER to Section 414
-0 1
Battery, Mounting and

Cables.
Fo r

Park/Neutral tests, GO to Pinpoint Test AC.
. Fo
r engine information,
REFER to Section 303
-01 En
gine
.
Engine cranks, but does
not fireSecurity
syst
em /Immobiliser
engaged
Thr o
ttle contaminated
Harness damage
Fu
el pump relay
Fue
l
system
R
e
fer to service action
S491
Contact dealer techni
cal
support for information
on security system. For fuel system,
REFER to Section 303
-0 4
Fuel Charging and
Controls.
Check bull etins for throttl
e cleaning procedure.
Check service actions.
Engine cranks an d
fires,
but will not start
F u
el pump relay
Thr
o
ttle contaminated
Purge
val
ve
Fue
l
pump
Engine coolan
t
temperature

(ECT) sensor
Spark plugs
fouled
Ignition coil
fail
ure(s)
Check f
o
r water ingress
into spark plug wells
HT sh o
rt to ground
(tracking) check rubber
boots for cracks/damage
Cyli
nder compression loss
(short-term. Refer to bulletin; 303-52)
Re
fer to service action
S491
Fo
r fuel pump relay tests,
REFER to Section 303
-0 4
Fuel Charging and
Controls.
. Check bulletins for throttl
e cleaning procedure.

Check fuel pressure. Refe r to Technical service
bulletins. For ECT sensor tests, GO to Pinpoint Test C.
. Fo
r ignition system,
REFER to Section 303
-07 En
gine Ignition
.
Check bulletins an d service a
ctions.
Di
f
ficult to
start
D iff
icult to start cold
Roc
h
ester valve
Batt
ery Thro
ttle contaminated
Fue
l
pump
Engine coolan
t
temperature

(ECT) sensor
Purge val
ve
Cyl
i
nder compression loss
(short-term. Refer to bulletin; 303-52)
Blocked part-load breather (s
ervice action S474)
R
e
fer to service action
S491
For R
ochester valv
e test, GO to Pinpoint Test AE.
. Fo
r battery information,
REFER to Section 414
-0 1
Battery, Mounting and

Cables.
Check bull etins for throttl
e cleaning procedure.
Check fuel pressure. For ECT sensor circuit tests,
GO to Pinpoint Test C.
. F
or evaporative
emissions tests,
REFER to Section 303
-1 3
Evaporative
Emiss
i
ons
.
R e
fer to bulletins for co
mpression information,
and service actions for part-load breather procedure and compressions.
Diff
icult to start hot
Roc
h
ester valve
Purge
val
ve
Thr
o
ttle contaminated
F
or R
ochester valv
e test, GO to Pinpoint Test AE.
. F
or evaporative emissions tests,
REFER to Section 303
-1 3
Evaporative

P
INPOINT TEST Y : DTC P1260; SECURITY INPUT MALFUNCTION
TE
ST
CONDITIONS
D
ETAILS/RESULTS/ACTIONS
Y1

: CHECK THE KTM TO ECM CIRCUIT FOR HIGH RESISTANCE
D

isconnect the ECM electrical connector, EM10.
1
D

isconnect the KTM electrical connector, FC22.
2
Me

asure the resistance between EM10, pin 06 (O) and FC22, pin 16 (O).
3
Is th

e resistance greater than 5 ohms?
Yes REPAIR the high resistance circui t. For additional information, refer to the wiring diagrams. CLEAR
the DTC. TEST the system for normal operation.
No INSTALL a new KTM. CLEAR the DTC. TEST the system for normal operation.
PINPO
INT TEST Z : DTC P1474; INTERCOOLER COOLANT PUMP RELAY MALFUNCTION
•
NOTE: Early production vehicl
es have connector pin numbers that differ fro m the volume production pin numbers shown.
Use the wire color code for pin identifi cation on early production vehicles.
TE
ST
CONDITIONS
D
ETAILS/RESULTS/ACTIONS
Z1

: CHECK THE INTERCOOLER PUMP RELAY TO ECM DRIVE CIRCUIT FOR HIGH RESISTANCE
Di

sconnect the battery negative terminal.
1
R

emove the intercooler pump relay.
2
D

isconnect the ECM electrical connector, EM13.
3
Meas

ure the resistance between the rela
y base, pin 01 and EM13, pin 10 (RY).
4
Is th
e resistance greater than 5 ohms?
Yes REPAIR the high resistance circui t. For additional information, refer to the wiring diagrams. CLEAR
the DTC. TEST the system for normal operation.
No GO to Z2
.
Z2
: CHECK THE INTERCOOLER PUMP RELAY TO EC
M DRIVE CIRCUIT FOR SHORT TO HIGH VOLTAGE
R
econnect the battery negative terminal.
1
Turn the ignition swi

tch to the ON
position.
2
Meas
ure the voltage between the
relay base, pin 01 and GROUND.
3
Is th
e voltage greater than 3 volts?
Yes REPAIR the short circuit. For addi tional information, refer to the wiring diagrams. CLEAR the DTC.
TEST the system for normal operation.
No GO to Z3
.
Z3
: CHECK THE INTERCOOLER PUMP RELAY TO
ECM DRIVE CIRCUIT FOR SHORT TO GROUND
Turn the ignition swi
tch to the OFF
position.
1
Meas
ure the resistance between th
e relay base, pin 01 and GROUND.
2
Is
the resistance less than 10,000 ohms?
Yes
REPAIR the short circuit. For addi tional information, refer to the wiring diagrams. CLEAR the DTC.
TEST the system for normal operation.
No GO to Z4
.
Z4: CHECK THE INTER
COOLER PUMP RELAY GROUND CIRCUIT
Meas

ure the resistance between th
e relay base, pin 02 and GROUND.
1
Is th
e resistance greater than 5 ohms?
Yes REPAIR the high resistance circui t. For additional information, refer to the wiring diagrams. CLEAR
the DTC. TEST the system for normal operation.
No INSTALL a new intercooler pump re lay. CLEAR the DTC. TEST the system for normal operation.
P
INPOINT TEST AA : DTC P1475; RADIATOR
FANS SLOW (SERIES) CIRCUIT MALFUNCTION
TE
ST
CONDITIONS
D
ETAILS/RESULTS/ACTIONS

Automatic Transmission/Transaxle - 4.0L NA V8 - AJ27/3.2L NA V8 - AJ26
- Transmission Descriptio
n
Description an
d Operation
Transmission As

sembly
Int
roduction

Compon
ent Descriptions
The t

orque converter:
Acts as a fluid

coupling between the
engine and transmission geartrain.
P
rovides multiplication of engine torque.
Cons

ists of an impeller, turbine and stat
or, housed within a converter cover.
Has a l
ock-up clutch with variable slip control.
The transmission casing:
Houses the geartrain and elec t
ro-hydraulic control unit.
Contains

the input speed sensor which measures turbine speed.
Contai

ns the output speed sensor which measures the transmission output speed.
It
em
Par
t Number
De
scription
1—Torque c

onverter housing
2—Tran

smission casing
3—Fluid pan


4—Transmission bre

ather
5—Re

ar extension housing
6—16

-way connector
7—Gear s

elector shaft