JAGUAR XFR 2010 1.G Workshop Manual
Page 991 of 3039
Engine - V8 S/C 5.0L Petrol - Oil Pan
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).
4. www.JagDocs.com
Page 992 of 3039
Installation
1. CAUTIONS:
Use only a plastic scraper when removing the sealing
material.
Use lint free cloth.
Make sure that the mating faces are clean and free of
corrosion and foreign material.
Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G)
to the areas shown, and tighten the bolts within 7
minutes.
Apply a bead of sealant, 2.5 mm diameter, to the
area indicated.
2. NOTE: Tighten the bolts in the sequence shown.
Torque: 12 Nm
3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).
Page 993 of 3039
303-1442
Rear Crankshaft Seal Installer
303-1443
Rear Crankshaft Cover Alignment Tool Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct. Published: 03-Dec-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.
Raise and support the vehicle.
3. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
4. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
Page 994 of 3039
5. CAUTIONS:
The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.
Make sure that no components fall off during removal.
NOTES:
Make sure that the crankshaft is not rotated.
Make sure the crankshaft and flexplate mating faces are clean before
installation.
6.
7.
8.
Page 995 of 3039
Page 996 of 3039
13.
14.
15.
NOTE: The high-pressure fuel pumps are removed from the illustration
for clarity.
16. CAUTIONS:
Be
prepared to
collect
escaping
fluids.
Make
sure that all
openings are
sealed. Use
new blanking
caps. www.JagDocs.com
Page 997 of 3039
17.
18.
19.
CAUTIONS:
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
Page 998 of 3039
20.
21.
22.
CAUTIONS:
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
Discard the fuel pipes.
Page 999 of 3039
23.
24.
25.
26. CAUTIONS:
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
CAUTION: Be prepared to collect escaping fluids.
CAUTION: Be prepared to collect escaping fluids.
Page 1000 of 3039
27.
28.
29.
30.
CAUTION: Be prepared to collect escaping fluids.
CAUTION: Be prepared to collect escaping fluids.
CAUTION: Be prepared to collect escaping fluids.