MITSUBISHI SPYDER 1990 Service Repair Manual

A U T O M A T I C T R A N S A X L E
OVERHAUL -Transaxle
56. End clutch cover57.Pulse58.Lock bolt59.Idler shaft60.Idler gear61.Spacer62.Gasket63. Idler gear cover
64. Differential bearing retainer
65.Spacer66. Differential front bearing cap
67.Differential assembly
6 8 . G a s k e t69. Differential cover70. Output retainer
71. Center differential assembly
72. Center bearing retainer’
73. Stopper ring
74. unit75. Center bearing retainer7 6 . F r o n t
77. Rear output shaft 78. Transaxle case
DISASSEMBLY
(1) Clean away any sand, mud,. etc. adhered the
transaxle.
(2) Place the transaxle assembly on the workbench w ith the
oil pan down.
(3) Remove the torque converter.
(4) Use the special tool to mount the dial gauge on trans-
axle case and the” play the .-
,
.
(5) Remove the pulse generator “A” and “B”.
(6) Remove the manual control lever, then remove th e
neutral position switch (PNP
(7)Remove the oil pan, magnets and gasket.

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
(8) Remove the oil filter from the
(9) Remove the 10 valve body mounting bolts.
the oil temperature sensor holder and remove
the oil temperature sensor harness from the clamp.
the finger of the solenoid valve grommet,
push the grommet into the case and ‘remove the valv e
body assembly.
out the oil temperature sensor.
the parking roller support.
the set screw of the control shaft and
remove the manual control shaft assembly.
the detent plate.
TSB Revision

AUTOMATIC .
OVERHAUL
the cover the cover
the differential the differential
the differential bearing retainer,
.
,
differential,
.
end clutch cover
holder and end
the end clutch
a

AUTOMATIC TRANSAXLEOVERHAUL -Transaxle
the thrust
the end ditch hub.
thrust bearing ..
NOTE
It may be stuck to
out the end
the idler gear mounting bolts, then
the idler gear cover and gasket.
the bolt stopper and the bolt.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
the tool, pull the idler
remove the idler gear and inner
t h e s p a c e r .
the oil pump installation
the special tool remove the oil
thrust washer
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
Thrust bearina
the input shaft and remove the front clutch assemb ly
and rear clutch assembly together.
thrust bearing
the clutch hub.
NOTE
The thrust race may be stuck to clutch hub.
thrust bearing
the drum.
TSB Revision

AUTOMATIC TRANSAXLE
O VE R H A U L
the band.
the servo coyer snap ring. Then
the servo switch.
the special tool, push in the
remove the snap ring.
the servo piston.
the anchor rod.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
the plug, then remove the exhaust plug.
the snap ring.
the special tool, remove the center
the reverse sun gear forward gear to-
gether.
the assembly.
TSB Revision

TRANSAXLE
OVERHAUL -Transaxle
the wave spring, return spring, reaction
brake discs, and brake plates.
the and the rear bearing;
,
__
49
the snap ring-and then remove output flange
assembly.
the output bearing
then remove the output bearing retainer, and outer
a rod 8 mm in.) in diameter and
in.) in length from the the figure
out the rear shaft. ,
Revision

OVERHAUL,, . . ,
special tool,
into the center and,
that bolt, remove the retainer and
race.
.
the center bearing
remove the ring and put a
puller or similar tool in the viscous
p u l l o u t t h e v i s c o u s . .
.
,,
the front bearing retainer bolt
Then, screw a bolt into the threaded hole the
front bearing retainer and,
that remove
front bearing retainer and race. ,