MITSUBISHI SPYDER 1990 Service Repair Manual

AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
TRANSAXLE23300100110
DISASSEMBLY AND REASSEMBLY
7 8
during reassembly.
15
14
1. converter assembly
Thrust washer 5. Front clutch assembly
6. Thrust race
7. Thrust bearing 8. Thrust washer 9. Rear clutch assembly
10. Thrust bearing
11. Rear clutch hub
12. Thrust bearing
13. Thrust race 14. band
15. drum
16.Snap ring17.Center support18.Wave spring19.Return spring20.Pressure plate
21.
Brake22. Brake plate
23. Reaction ‘plate
24. gear
25. Thrust bearing
r a c e 26,27. sun 28. Planetary 29. Thrust bearing 30. Output
T S B R e v i s i o n

AUTOMATIC TRANSAXLE
OVERHAUL
-Transaxle
32
16
11
70 18
I I
Nm
8
4938
I72
97
24
8. . . . .5
I
42
11 8
31.Oil dipstick
32. Oil filler tube
33.Snap ring34. servo switch35.Snap ring
36. servo piston37.Spring38.Anchor rod
39.Detent plate40. Manual control shaft
5960
6670 Nm51
41. Parking roller support
4 2 . O i l p a n
43. Gasket
44. Oil
45. Oil screen
46. Valve
47. Manual 4 6 .
( P N P4 9 . E n d
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL
50.Bearing. retainer51. Thrust bearing 52. End clutch hub53.Thrust washer
54. End clutch assembly
55.O-ring56. End clutch cover57.Pulse generator58.Lock bolt59.Idler shaft60.Idler gear61.Spacer
64. bearing- 65. Outer 66. Diff
67.
I-, front a s s e m b l y ,
68. ,
69. cover
7 0 . - -
72..
(1) Clean away any sand, the’
transaxle.
(2) Place the transaxle assembly
oil pan down.
(3) Remove the torque converter;
(4)Use the special tool to mount
axle case and measure ‘the.
. .
. .
.
(5) Remove the pulse
. . .
. . .a-.
(6) Remove the manual control lever, ‘then
neutral position switch (PNP
,
. .
(7) Remove the oil pan, magnets and
.
,
,
, .
.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL,
(8) Remove the oil filter from the valve body.
.
,
(9) Remove the 10 valvebody mounting
the oil temperature sensor holder and
oil temperature sensor clamp,
,
the finger of the solenoid valve harness grommet,,
push the grommet into and remove the valve
body assembly.
out the oil temperature sensor.
the parking roller
I-
*
the set screw of the manual shaft and’
remove the manual control shaft
the detent plate.
--. .
TSB Revision

A U T O M A T I C T R A N S A X L E
OVERHAUL Transaxle
the differential cover
the differential
. .
the differential outer’
race.
,,
the differential assembly.. .
out the end clutch’ installation
move the cover holder and end
the end assembly.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL
-Transaxle
the thrust plate.
the end clutch hub.
t h r u s t b e a r i n g
NOTE
It may be stuck to the and clutch
out the end clutch shaft.
the idler gear cover mounting then’
the idler gear cover and gasket.
the bolt stopper and remove the bolt.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL
the special tool, pull out the. shaft and
remove the idler gear and race.
the spacer.
the oil pump bolts.
. ,
the special tool to remove the pump.‘
,
t h r u s t w a s h e r .
,
TSB Revision

AUTOMATIC TRANSAXLEOVERHAUL -Transaxle
the input shaft and remove the front
and rear clutch assembly together.
thrust bearing
the clutch hub.
NOTE
. .
The thrust race may be to the clutch ‘hub.
thrust bearing
,
the drum.
TSBRevision

TSB
t h e .
the servo cover cover
t h et h e
. .
, ,
,, ,
special tool, push “in the
remove the snap . .. .
t h e

-Transaxle
plug, then remove the
the snap ring.
the special tool, remove the. ‘support.
TSB Revision
the sun gear forward to-
gether.
.
..
the carrier assembly.