NISSAN NOTE 2016 Service Repair Manual

TM-230
< PERIODIC MAINTENANCE >[CVT: RE0F11A]
CVT FLUID
• During adjustment of the CVT fluid level, check CO
NSULT so that the oil temperature may be main-
tained from 35 to 45 °C (95 to 113 °F).
• Use caution when looking into the drain hole as th ere is a risk of dripping fluid entering the eye.
1. Check that the selector lever is in the “P ” position, then completely engage the parking brake.
2. Start the engine.
3. Adjust the CVT fluid temperature to be approximately 40 °C (104° F).
NOTE:
The CVT fluid is largely affected by temperature. Therefore be sure to use CONSULT and check the
“FLUID TEMP” under “TRANSMISSION” in “Data Monitor” while adjusting.
4. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it to the “P” position.
NOTE:
Hold the lever at each position for 5 seconds.
5. Lift up the vehicle.
6. Check that there is no CVT fluid leakage.
7. Remove the drain plug. Refer to TM-242, "
Removal and Installation".
8. Install the charging pipe set (KV311039S0) (A) into the drain plug hole.
CAUTION:
Tighten the charging pipe by hand.
9. Install the ATF changer hose (B) to the charging pipe. CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
10. Fill approximately 0.5 liter (1/2 lmp qt) of the CVT fluid.
11. Remove the ATF changer hose from the charging pipe, and check that the CVT fluid drains out from the charging pipe. If it
does not drain out, perform charging again.
CAUTION:
Perform this work with the vehicle idling.
12. When the flow of CVT fluid slows to a drip, remove the charging pipe from the oil pan.
13. Tighten the drain plug to the specified torque. Refer to TM-242, "
Removal and Installation".
CAUTION:
Never reuse drain plug gasket.
14. Lift down the vehicle.
15. Stop the engine.
JSDIA1876ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CVT SHIFT SELECTORTM-231
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded ViewINFOID:0000000012431175
Removal and InstallationINFOID:0000000012431176
CAUTION:
Always apply the parking brake before pe rforming removal and installation.
REMOVAL
1. Move the shift selector to the “N” position.
2. Remove the shift selector handle. Refer to TM-232, "
Disassembly and Assembly".
3. Remove the center console. Refer to IP-18, "
Removal and Installation".
4. Disconnect the harness connectors from shift selector.
5. Move the shift selector to the “P” position.
6. Remove the key interlock cable from the shift selector assembly. Refer to TM-237, "
Exploded View".
7. Remove the control cable from the shift selector assembly. Refer to TM-234, "
Exploded View".
8. Remove the shift selector assembly.
INSTALLATION
Installation is in the reverse order of removal.
1. Shift selector handle 2. Lock pin3. Shift selector handle cover
4. Position indication panel 5. Shift selector assembly
ALDIA0263GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-232
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
CVT SHIFT SELECTOR
• When connecting the control cable (1) to the shift selector assem-
bly (2), face the grooved surface of the rib (A) up and insert the
control cable until it stops.
Disassembly and AssemblyINFOID:0000000012431177
DISASSEMBLY
1. Slide the shift selector handle cover (1) down. CAUTION:
Do not damage the shift selector handle cover.
2. Pull out the lock pin (2).
3. Pull the shift selector handle (3) and shift selector handle cover upward to remove.
4. Remove the position lamp.
5. Disengage the hooks (A) (4 locations), and lift up the position indication panel (1) to separate it from the shift selector assem-
bly (2).
CAUTION:
Do not damage the shift selector assembly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Follow the procedure below to install the shift selector handle.
1. Install the lock pin (2) onto the shift selector handle (3).
2. Install the shift selector handle cover (1) onto the shift selectorhandle.
3. Press the shift selector handle onto the shift selector until it clicks.
CAUTION:
• When pressing the shift selector handle onto the shift
selector, do not press the shift selector handle button.
• Do not strike the shift selector handle to install it.
InspectionINFOID:0000000012431178
INSPECTION AFTER INSTALLATION
JSDIA1624ZZ
JSDIA1796ZZ
ALDIA0264ZZ
JSDIA1796ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CVT SHIFT SELECTORTM-233
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Check CVT position. Refer to TM-133, "Inspection".
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-234
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
CONTROL CABLE
CONTROL CABLE
Exploded ViewINFOID:0000000012431179
Removal and InstallationINFOID:0000000012431180
CAUTION:
Always apply the parking brake before performing removal
and installation.
REMOVAL
1. Remove the battery negative terminal. Refer to PG-70, "Exploded View".
2. Remove the TCM and bracket. Refer to TM-239, "
Removal and Installation".
3. Remove the IPDM E/R. Refer to PCS-30, "
Removal and Installation".
4. Remove the battery tray and bracket.
5. Remove instrument lower panel LH. Refer to IP-24, "
Removal and Installation".
6. Remove the center console assembly. Refer to IP-18, "
Removal and Installation".
7. Remove the control cable from the shift selector assembly.
8. Disengage the pawls (B) of the grommet (A), and pull downward to remove.
9. Remove the control cable nut from the manual lever.
1. Bracket B 2. Lock plate3. Transaxle assembly
4. Bracket A 5. Control cable6. Shift selector assembly
A: Manual lever B: Grommet
JSDIA1921GB
JSDIA1809ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CONTROL CABLETM-235
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
10. Remove the lock plate (1).
11. Remove the heat plate.
12. Remove the control cable (1) from the bracket (2).
13. Remove the control cable from the vehicle.
14. Remove bracket.
INSTALLATION
Installation is in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the pawls (B) make a click sound.
CAUTION:
Check that pulling down on the grommet does not disconnect
it.
• Pay attention to the following when connecting the control cable to the shift selector.
1. When connecting the control cable (1) to the shift selector assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
JSDIA1812ZZ
: Front
JPDIA0107ZZ
JSDIA1809ZZ
JSDIA1624ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-236
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
CONTROL CABLE
2. Install the socket (A) onto the shift selector assembly.
CAUTION:
• Insert the socket into the shift selector assembly, thenpush it firmly in place.
• Check that pulling on the so cket does not disconnect it.
Inspection and AdjustmentINFOID:0000000012431181
INSPECTION AFTER INSTALLATION
Check CVT position. Refer to TM-133, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust CVT position. Refer to TM-133, "Adjustment".
JSDIA1810ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

KEY INTERLOCK CABLETM-237
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
KEY INTERLOCK CABLE
Exploded ViewINFOID:0000000012431182
Removal and InstallationINFOID:0000000012431183
REMOVAL
CAUTION:
Always apply the parking brake before pe rforming removal and installation.
1. Move the shift selector to the “N” position.
2. Remove the shift selector handle. Refer to TM-232, "
Disassembly and Assembly".
3. Remove the instrumental lower panel LH. Refer to IP-24, "
Removal and Installation".
4. Remove steering column covers. Refer to IP-17, "
Removal and Installation".
5. Remove the center console. Refer to IP-18, "
Removal and Installation".
6. Move the shift selector to the “P” position.
7. Press the pawls (B) of the key interlock cable slider (A) while sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.
8. Remove the key interlock cable from the shift selector assembly.
1. Shift selector assembly 2. Key interlock cable A: Steering lock unit
B: Lock plate C: Clip
ALDIA0262ZZ
(E) :Key interlock rod
JSDIA1797ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-238
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
KEY INTERLOCK CABLE
9. Lift lock plate (A) in the direction of the arrow ( C) and remove
in the direction of the arrow ( D).
10. Remove the key interlock cable from the steering lock unit.
11. Disengage the clips and remove the key interlock cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Temporarily install the adjust holder (A) to the key interlock rod (B).
• Install the casing cap (C) to the cable bracket (D) on the shift
selector assembly.
CAUTION:
• Do not bend or twist key interlock cable excessively wheninstalling.
• After installing key interlock cable to cable bracket (D) on shift selector assembly, make sure casing caps (C) is firmly
secured in cable bracket (D) on shift selector assembly.
• If casing cap (C) is loose [less than 39.2 N (4.0 kg, 8.8 lb) removing force], replace key interlock cable.
• Slide the slider (A) toward the key interlock rod (D) while pressing the pull lock (B) down to securely connect the adjust holder (C)
with the key interlock rod (D).
CAUTION:
• Do not press tabs when holding slider (A).
• Do not apply any side to side force to key interlock rod (D)
when sliding slider (A).
InspectionINFOID:0000000012431184
INSPECTION AFTER INSTALLATION
• Check the CVT operation. If a malfunction is found, adjust the CVT position. Refer to TM-232, "Inspection".
• Make sure the key can be removed only when the shift selector is in the “P” position.
• Make sure the ignition switch will not turn to LOCK pos ition when the shift selector is not in the “P” position.
(1) :Key interlock cable
(B) :Steering lock unit
JSDIA1798ZZ
JSDIA1799ZZ
JSDIA1800ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TCM
TM-239
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
TCM
Exploded ViewINFOID:0000000012431185
Removal and InstallationINFOID:0000000012431186
CAUTION:
• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON- FORM CVTF DETERIORATION” in MAINTENANCE BOOKLET, before starting the operation.
• When replacing TCM, perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to TM-125,
"Description".
• When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and then replace TCM.
REMOVAL
1. Remove the battery. Refer to PG-70, "Removal and Installation (Battery)".
2. Disconnect the harness connector from the TCM.
3. Remove the TCM and bracket as an assembly.
4. Remove the TCM from the bracket (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
AdjustmentINFOID:0000000012431187
ADJUSTMENT AFTER INSTALLATION
Perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to TM-125, "Description".
1. TCM2. Bracket3. Clip
Front
AWBIA1482ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com