NISSAN NOTE 2016 Service Repair Manual

WCS-46
< DTC/CIRCUIT DIAGNOSIS >
KEY SWITCH SIGNAL CIRCUIT (WITHOUT INTELLIGENT KEY)
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4. CHECK KEY SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch harness connector M27 terminal 2 and ground.
Is the inspection result normal?
YES >> Replace key switch.
NO >> Repair or replace harness.
Component InspectionINFOID:0000000012432709
1. CHECK KEY SWITCH
1. Turn ignition switch OFF.
2. Disconnect key switch.
3. Check continuity between key switch terminals 1 and 2.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace key switch.
BCM
GroundContinuity
Connector Terminal
M18 37 No
Te r m i n a l s
Vo l ta g e
(Approx.)
(+)
(–)
Key switch Terminal
M27 2Ground Battery voltage
Terminal ConditionContinuity
12 When key is removed from key cylinder
No
When key is inserted into key cylinder Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

WCS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
WCS-47
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARN ING CONTINUES SOUNDING, OR
DOES NOT SOUND
DescriptionINFOID:0000000012432710
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking brake applied.
Diagnosis ProcedureINFOID:0000000012432711
NOTE:
To identify combination meter type, refer to WCS-3, "
Information".
1.CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-54, "Removal and Installation" (Type A) or MWI-115,
"Removal and Installation" (Type B).
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Check the parking brake switch signal circuit. Refer to WCS-42, "
TYPE A : Diagnosis Procedure" (Type A) or
WCS-43, "
TYPE B : Diagnosis Procedure" (Type B).
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to WCS-43, "
TYPE A : Component Inspection" (Type A) or WCS-44,
"TYPE B : Component Inspection" (Type B).
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-54, "Removal and Installation" (Type A) or MWI-115,
"Removal and Installation" (Type B).
NO >> Replace parking brake switch. Refer to PB-6, "
Exploded View".
Condition Seat belt warning lamp
When parking brake is applied ON
When parking brake is released OFF
Revision: August 2015 2016 Versa Note

cardiagn.com

WCS-48
< SYMPTOM DIAGNOSIS >
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
THE SEAT BELT REMINDER WARN ING CONTINUES SOUNDING, OR
DOES NOT SOUND
DescriptionINFOID:0000000012432712
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis ProcedureINFOID:0000000012432713
NOTE:
To identify combination meter type, refer to WCS-3, "
Information".
1.CHECK WARNING CHIME OPERATION
1. Select “BUZZER” of “BCM” using CONSULT.
2. Perform “SEAT BELT WARN TEST” in “Active Test”.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (Type A) or MWI-115,
"Removal and Installation" (Type B).
2.CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation" (with Intelligent Key system) or BCS-
137, "Removal and Installation" (without Intelligent Key system).
NO >> GO TO 3.
3.CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT
Check the seat belt buckle switch LH circuit. Refer to WCS-39, "
TYPE A : DiagnosisProcedure" (Type A) or
WCS-40, "
TYPE B : DiagnosisProcedure" (Type B).
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness or connector.
4.CHECK SEAT BELT BUCKLE SWITCH LH
Check the seat belt buckle switch LH. Refer to WCS-40, "
TYPE A : Component Inspection" (Type A) or WCS-
41, "TYPE B : Component Inspection" (Type B).
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-54, "Removal and Installation" (Type A) or MWI-115,
"Removal and Installation" (Type B).
NO >> Replace the seat belt buckle switch LH. Refer to SR-35, "
Removal and Installation".
Condition Seat belt warning lamp
Driver seat belt fastened OFF
Driver seat belt not fastened ON
Revision: August 2015 2016 Versa Note

cardiagn.com

WCS
THE LIGHT REMINDER WARNING DOES NOT SOUNDWCS-49
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
THE LIGHT REMINDER WA RNING DOES NOT SOUND
DescriptionINFOID:0000000012432714
Light reminder warning chime does not sound even though headlamps are illuminated.
Diagnosis ProcedureINFOID:0000000012432715
1.CHECK COMBINATION SWITCH (L IGHTING SWITCH) OPERATION
Check that the headlamps operate normally by operat ing the combination switch (lighting switch).
Do they operate normally?
YES >> GO TO 2.
NO >> Refer to WCS-32, "
Work Flow".
2.CHECK FRONT DOOR SWITCH LH SIGNAL CIRCUIT
Check the front door switch LH signal circuit. Refer to DLK-98, "
Diagnosis Procedure" (with Intelligent Key
system) or DLK-232, "
Diagnosis Procedure" (without Intelligent Key system).
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK FRONT DOOR SWITCH LH
Check the front door switch LH. Refer to DLK-99, "
Component Inspection" (with Intelligent Key system) or
DLK-234, "
Component Inspection" (without Intelligent Key system).
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation" (with Intelligent Key system) or BCS-
137, "Removal and Installation" (without Intelligent Key system).
NO >> Replace front door switch LH. Refer to DLK-181, "
Removal and Installation" (with Intelligent Key
system) or DLK-308, "
Removal and Installation" (without Intelligent Key system).
Revision: August 2015 2016 Versa Note

cardiagn.com

WCS-50
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
THE KEY WARNING DOES NOT SOUN D (WITHOUT INTELLIGENT KEY)
DescriptionINFOID:0000000012432716
The key warning chime does not sound, when all of the following conditions are fulfilled.
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (front door switch LH ON)
Diagnosis ProcedureINFOID:0000000012432717
1.CHECK BCM INPUT SIGNAL
1. Connect CONSULT.
2. Select the “Data Monitor” of “BCM (BUZZER)” and check t he “KEY ON SW” monitor value.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-137, "Removal and Installation".
NO >> GO TO 2.
2.CHECK KEY SWITCH SIGNAL CIRCUIT
Check the key switch signal circuit. Refer to WCS-45, "
DiagnosisProcedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK KEY SWITCH
Check the key switch. Refer to WCS-46, "
Component Inspection".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-137, "Removal and Installation".
NO >> Replace key switch.
Monitor item Condition Status
KEY ON SW Under the condition of buzzer input
On
Except above Off
Revision: August 2015 2016 Versa Note

cardiagn.com

WW-1
DRIVER CONTROLS
C
DE
F
G H
I
J
K
M
SECTION WW
A
B
WW
N
O P
CONTENTS
WIPER & WASHER
PRECAUTION ....... ........................................3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
Procedure without Cowl Top Cover .......................3
Precaution for Work ..................................................3
PREPARATION ............................................5
PREPARATION .............................................. .....5
Special Service Tools .......................................... ......5
Commercial Service Tool ..........................................5
SYSTEM DESCRIPTION ..............................6
COMPONENT PARTS ................................... .....6
Component Parts Location .................................. ......6
SYSTEM ..............................................................8
FRONT WIPER AND WASHER SYSTEM ............. ......8
FRONT WIPER AND WASHER SYSTEM : Sys-
tem Diagram ..............................................................
8
FRONT WIPER AND WASHER SYSTEM : Sys-
tem Description .........................................................
8
FRONT WIPER AND WASHER SYSTEM : Fail-
Safe .........................................................................
10
REAR WIPER AND WASHER SYSTEM ............... ....10
REAR WIPER AND WASHER SYSTEM : System
Diagram ...................................................................
10
REAR WIPER AND WASHER SYSTEM : System
Description ..............................................................
10
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) .........................................
13
COMMON ITEM ..................................................... ....13
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) .....................................................
13
WIPER .................................................................... ....14
WIPER : CONSULT Function (BCM - WIPER) .......14
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) .............................
15
COMMON ITEM ..................................................... ....15
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) .....................................................
15
WIPER .................................................................... ....16
WIPER : CONSULT Function (BCM - WIPER) .......16
DIAGNOSIS SYSTEM (IPDM E/R) ...................17
Diagnosis Description ..............................................17
CONSULT Function (IPDM E/R) .............................18
ECU DIAGNOSIS INFORMATION ..............21
BCM, IPDM E/R .................................................21
List of ECU Reference ......................................... ....21
WIRING DIAGRAM ......................................22
FRONT WIPER AND WASHER SYSTEM ........22
Wiring Diagram .................................................... ....22
REAR WIPER AND WASHER SYSTEM ..........28
Wiring Diagram ........................................................28
BASIC INSPECTION ...................................33
DIAGNOSIS AND REPAIR WORKFLOW ........33
Work Flow ............................................................ ....33
DTC/CIRCUIT DIAGNOSIS .........................35
WIPER AND WASHER FUSE ...........................35
Description ........................................................... ....35
Diagnosis Procedure ...............................................35
FRONT WIPER MOTOR LO CIRCUIT ..............36
Component Function Check ....................................36
Diagnosis Procedure ...............................................36
Revision: August 2015 2016 Versa Note

cardiagn.com

WW-2
FRONT WIPER MOTOR HI CIRCUIT ................38
Component Function Check ................................ ...38
Diagnosis Procedure ..............................................38
FRONT WIPER AUTO STOP SIGNAL CIR-
CUIT ...................................................................
40
Component Function Check ................................ ...40
Diagnosis Procedure ..............................................40
FRONT WIPER MOTOR GROUND CIRCUIT ...42
Diagnosis Procedure ..............................................42
WASHER MOTOR CIRCUIT .............................43
Diagnosis Procedure ........................................... ...43
WASHER SWITCH ............................................44
Description ........................................................... ...44
Component Inspection ............................................44
REAR WIPER MOTOR CIRCUIT ......................46
Component Function Check ................................ ...46
Diagnosis Procedure ..............................................46
REAR WIPER AUTO STOP SIGNAL CIRCUIT
...
48
Component Function Check ................................ ...48
Diagnosis Procedure ..............................................48
SYMPTOM DIAGNOSIS .............................50
WIPER AND WASHER SYSTEM SYMPTOMS
...
50
Symptom Table ................................................... ...50
FRONT WIPER DOES NOT OPERATE ............53
Description ........................................................... ...53
Diagnosis Procedure ..............................................53
NORMAL OPERATING CONDITION ................55
Description ........................................................... ...55
REMOVAL AND INSTALLATION ...............56
WASHER TANK ............................................. ...56
Exploded View ..................................................... ...56
Removal and Installation ........................................56
FRONT WASHER MOTOR ................................58
Exploded View ..................................................... ...58
Removal and Installation ........................................58
WASHER FLUID LEVEL SWITCH ....................59
Removal and Installation ..................................... ...59
FRONT WASHER NOZZLE AND TUBE ...........60
Exploded View ..................................................... ...60
WASHER NOZZLE ................................................. ...60
WASHER NOZZLE : Removal and Installation .......60
WASHER NOZZLE : Adjustment ............................61
WASHER TUBE ..................................................... ...61
WASHER TUBE : Removal and Installation ...........61
WASHER TUBE : Inspection ..................................62
FRONT WIPER ARM .........................................63
Exploded View ..................................................... ...63
Removal and Installation .........................................63
Adjustment ........................................................... ...64
FRONT WIPER BLADE .....................................65
Removal and Installation .........................................65
FRONT WIPER DRIVE ASSEMBLY .............. ...66
Exploded View ..................................................... ...66
Removal and Installation .........................................66
Exploded View ..................................................... ...67
Disassembly and Assembly ....................................67
WIPER AND WASHER SWITCH ......................68
Removal and Installation .........................................68
REAR WIPER ARM ........................................ ...69
Exploded View ..................................................... ...69
Removal and Installation .........................................69
Adjustment ........................................................... ...70
REAR WIPER BLADE .......................................71
Removal and Installation .........................................71
REAR WIPER MOTOR ................................... ...72
Exploded View ..................................................... ...72
Removal and Installation .........................................72
REAR WASHER NOZZLE AND TUBE .......... ...73
Component Parts Location .................................. ...73
WASHER NOZZLE ................................................. ...73
WASHER NOZZLE : Removal and Installation .......73
WASHER NOZZLE : Adjustment ............................73
WASHER TUBE ..................................................... ...74
WASHER TUBE : Removal and Installation ...........74
SERVICE DATA AND SPECIFICATIONS
(SDS) .......... ................................. ...............
76
SERVICE DATA AND SPECIFICATIONS
(SDS) .............................................................. ...
76
Specifications ....................................................... ...76
Revision: August 2015 2016 Versa Note

cardiagn.com

PRECAUTIONSWW-3
< PRECAUTION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012433192
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Procedure without Cowl Top CoverINFOID:0000000012433193
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc. to prevent damage to
the windshield.
Precaution for WorkINFOID:0000000012433194
• When removing or disassembling each component, be ca reful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusabl e part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
-Oily dirt:
PIIB3706J
Revision: August 2015 2016 Versa Note

cardiagn.com

WW-4
< PRECAUTION >
PRECAUTIONS
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirtyarea.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: August 2015 2016 Versa Note

cardiagn.com

PREPARATIONWW-5
< PREPARATION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000012433195
The actual shape of the tools may differ from those illustrated here.
Commercial Service ToolINFOID:0000000012433196
Tool number
(TechMate No.)
Tool name Description
—
(J-46534)
Trim Tool Set Removing trim components
AWJIA0483ZZ
Tool name
Description
Washer nozzle adjuster Adjusting washer nozzle
JSLIA0149ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com