NISSAN PRIMERA 1999 Electronic Repair Manual

REMOVAL Ð Headlining
Wagon
p1Remove front and rear seats. Refer to ªSEATº for details, BT-40.
p2Remove front and rear seat belts. Refer to ªSEAT BELTSº in RS section for details.
p3Remove body side trim. Refer to ªSide and Floor Trimº for details, BT-22.
p4Remove sunroof switch. (Models equipped with electric sunroof)
p5Remove handle and lamp cover. (Models equipped with manual sunroof)
p6Remove sunroof welt. (Models equipped with sunroof)
p7Remove sun visors.
p8Remove interior lamp (center) and interior lamp (rear).
p9Remove assist grips.
p10Remove clipsC103.
p11Remove luggage net escutcheons.
p12Remove roof rear garnish.
p13Remove speakers.
p14Remove headlining.
NBT045 Metal clip
Manual type
Metal clip
C103
p9
INTERIOR TRIM
Roof Trim (Cont'd)
BT-27

Trunk Room Trim
YBT018 Metal clipFrontMetal clip
SEC. 849
INTERIOR TRIM
BT-28

Luggage Room Trim
NBF275
INTERIOR TRIM
BT-29

Back Door Trim
REMOVAL Ð Back door trim
p1Remove back door lower finisher.
p2Remove back door upper finisher.
p3Remove back door side finisher.
p4Remove high-mounted stop lamp.
NBT054 Metal clip
Metal clip Metal clip
Metal clip Metal clip
Metal clip2.9 - 3.8 N´m (0.30 - 0.39 kg-m, 26.0 - 33.9 in-lb)
Metal clip
INTERIOR TRIM
BT-30

NBT051
EXTERIOR
BT-31

NBT052
EXTERIOR
BT-32

p1p2Hood front sealing rubber
p3p4Cowl top seal and cowl top grille
p5Windshield side molding
Mounted with screws.
p6Windshield upper molding
p7Drip weatherstrip
YBT020 Hood front sealing rubber
SEC. 650
Radiator core support
sealing rubber
YBT021
SEC. 660
Cowl top seal
Cowl top grille
YBT022 Windshield side moldingScrew
SBF342H
SEC. 720
1. Cut off sealant at glass end.
2. Clean the side on which panel was mounted.
3. Set molding fastener and apply primer to body panel, and
apply sealant to body.
Molding
Clip
Fastener
Double-faced
adhesive tape
Apply primer
Apply sealant
Sealant Dam rubberGlass
4. Install molding by aligning the molding mark
located on center with vehicle center.
Be sure to install tightly so that there is no gap
around the corner.
NBT058 Drip
weatherstripFront
pillar
Drip
weatherstripBody
panelUpper
SEC. 720
Front
EXTERIOR
BT-33

p8Body side welt
p9Door weatherstrip
p10Door outside molding
p11Sunroof lid weatherstrip
SBT043 Outside
YBT024
EC. 800×820
ClipClip
ClipClip
SBT067
Front door
SEC. 800Screw
Clip
Door outer panel Door outer molding
Rear door
SEC. 820
Screw
Door panelClipDoor outer molding
YBT025 Roof panel
Glass lid
Sunroof lid
weatherstrip
Sunroof rail
assembly
Front
SEC. 736
EXTERIOR
BT-34

p12Side guard molding
lWith a vehicle coated with Hard Clear Coat,
use double-faced 3M adhesive tape Product
No. 5572 or equivalent, after priming with
3M primer Product No. N-200 or C-100 or
equivalent.
p13Rear window upper molding
Basically the same as windshield upper molding.
Refer to
p6Windshield upper molding.
p14Rear window lower molding
p15Trunk lid weatherstrip
p16Back door window molding
5-door hatchback
Wagon
See ªBack door windowº. Refer to BT-57.
YBT026
SEC. 766
Locating pins
: Double-faced adhesive tape
Heat gun
YBT027 Rear window glass
Rear window lower
molding
Removal: Remove molding by cutting around its perimeter.
Installation: Refer to ªRear windowº.
SBT069
SEC. 843
Marking at vehicle center
Vehicle center
Bonding portion
YBT050 300 (11.81)
60
(2.36)
Unit: mm (in)
Glass Back door moldingBack door molding GlassBack door molding Double side adhesive tapeGlass Back door molding
Back door molding
Glass
EXTERIOR
BT-35

p17Back door weatherstrip
Wagon
5-door hatchback
NBF278 Vehicle center
Bonding point
YBT056 Vehicle center
Bonding portion
EXTERIOR
BT-36