NISSAN TEANA 2014 Service Manual

SYSTEMBRC-15
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Front RH brake caliper• Since the cut valve 1 and the suction valve 1 are closed, the front RH brake caliper, master cylinder, and res- ervoir are blocked. This maintains fluid pressure applied on the front RH brake caliper. The pressurization for
the left caliper is controlled separately from the right caliper.
Front LH brake caliper
• Since the cut valve 2 and the suction valve 2 are clos ed, the front LH brake caliper, master cylinder, and res-
ervoir are blocked. This maintains fluid pressure app lied on the front LH brake caliper. The pressurization for
the right caliper is controlled separately from the left caliper.
Rear RH brake caliper
• Since the cut valve 2 and the suction valve 2 are clos ed, the rear RH brake caliper, master cylinder, and res-
ervoir are blocked. This maintains fluid pressure applied on the rear RH brake caliper. The pressurization for
the left caliper is controlled separately from the right caliper.
Rear LH brake caliper• Since the cut valve 1 and the suction valve 1 are closed, the rear LH brake caliper, master cylinder, and res- ervoir are blocked. This maintains fluid pressure app lied on the rear LH brake caliper. The pressurization for
the right caliper is controlled separately from the left caliper.
VDC and TCS Functions Operating (Pressure Decreases)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
ABS IN valve Power supp ly is not supplied (open) Power supp ly is not supplied (open)
ABS OUT valve Power supp ly is not supplied (close) Power supply is not supplied (close)
Each brake caliper (fluid pressure) — Pressure holds Name Not activated Pressure holds
ALFIA0311GB
Name Not activated During pressure decreases
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-16
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
SYSTEM
Front RH brake caliper• Since the suction valve 1 and the ABS OUT valve are closed and the cut valve 1 and the ABS IN valve are
open, the fluid pressure applied on the front RH brake ca liper is reduced by supplying the fluid pressure to
the master cylinder via the ABS IN valve and the cut valv e 1. The pressurization for the right caliper is con-
trolled separately from the left caliper.
Front LH brake caliper
• Since the suction valve 2 and the ABS OUT valve are closed and the cut valve 2 and the ABS IN valve are open, the fluid pressure applied on the front LH brake caliper is reduced by supplying the fluid pressure to
the master cylinder via the ABS IN valve and the cut valv e 2. The pressurization for the left caliper is con-
trolled separately from the right caliper.
Rear RH brake caliper
• Since the suction valve 2 and the ABS OUT valve are closed and the cut valve 2 and the ABS IN valve are open, the fluid pressure applied on the rear RH brake ca liper is reduced by supplying the fluid pressure to
the master cylinder via the ABS IN valve and the cut valv e 2. The pressurization for the right caliper is con-
trolled separately from the left caliper.
Rear LH brake caliper• Since the suction valve 1 and the ABS OUT valve are closed and the cut valve 1 and the ABS IN valve are open, the fluid pressure applied on the rear LH brake cali per is reduced by supplying the fluid pressure to the
master cylinder via the ABS IN valve and the cut valve 1. The pressurization for the left caliper is controlled
separately from the right caliper.
Component Parts and Function
VALVE OPERATION (ABS AND EBD FUNCTIONS)
The control unit built into the ABS act uator and electric unit (control unit) controls fluid pressure of the brake
calipers by operating each valve.
ABS IN valve Power supply is not supplied (open) Power supply is not supplied (open)
ABS OUT valve Power supply is not supplied (close) Power supply is not supplied (close)
Each brake caliper (fluid pressure) — Pressure decreases Name Not activated During pressure decreases
Component Function
Pump Returns the brake fluid reserved in reservoir to master cylinder by reducing pressure.
Motor Activates the pu mp according to signals from ABS actuator and el ectric unit (control unit).
Cut valve 1
Cut valve 2 Shuts off the ordinary brake line from master cylinder.
Suction valve 1
Suction valve 2 Supplies the brake fluid from master cylinder to the pump.
ABS IN valve Switches the fluid pressure line to increase or hold according to signals from control unit.
ABS OUT valve Switches the fluid pressure li ne to increase, hold or decrease according to si gnals from control unit.
Return check valve Returns the brake fluid from brake caliper to master cylinder by bypassing orifice of each valve when
brake is released.
Reservoir Temporarily reserves the brake fluid drained from brake caliper, so that pressure efficiently decreas-
es when decreasing pressure of brake caliper.
Pressure sensor Detects the brak e fluid pressure and transmits signal to ABS actuator and electric unit (control unit).
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMBRC-17
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Brake Pedal Applied or ABS Function
Operating (Pressure Increases)
Front RH brake caliper
• When the cut valve 1 and the ABS IN valve opens, brake fluid is supplied to the front RH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
Front LH brake caliper• When the cut valve 2 and the ABS IN valve opens, brake fl uid is supplied to the front LH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
Rear RH brake caliper• When the cut valve 2 and the ABS IN valve opens, brake fluid is supplied to the rear RH brake caliper from the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
Rear LH brake caliper
• When the cut valve 1 and the ABS IN valve opens, brake fl uid is supplied to the rear LH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
ALFIA0312GB
Name Not activated During pressure increases
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
ABS IN valve Power supp ly is not supplied (open) Power supp ly is not supplied (open)
ABS OUT valve Power supp ly is not supplied (close) Power supply is not supplied (close)
Each brake caliper (fluid pressure) — Pressure increases
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-18
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
SYSTEM
ABS Function Starts Operating (Pressure Holds)
Front RH brake caliper
• Since the ABS IN valve and the ABS OUT valve are cl
osed, the front RH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the front RH brake caliper.
Front LH brake caliper
• Since the ABS IN valve and the ABS OUT valve are cl osed, the front LH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the front LH brake caliper.
Rear RH brake caliper
• Since the ABS IN valve and the ABS OUT valve are cl osed, the rear RH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the rear RH brake caliper.
Rear LH brake caliper
• Since the ABS IN valve and the ABS OUT valve are cl osed, the rear LH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the rear LH brake caliper.
ALFIA0313GB
Name Not activated During pressure holds
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
ABS IN valve Power supply is not supplied (open) Power supply is supplied (close)
ABS OUT valve Power supply is not supplied (close) Power supply is not supplied (close)
Each brake caliper (fluid pressure) — Pressure holds
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMBRC-19
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
ABS Function Operating
(Pressure Decreases)
Front RH brake caliper
• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the front RH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
Front LH brake caliper• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the front LH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
Rear RH brake caliper• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the rear RH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
Rear LH brake caliper
• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the rear LH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
ALFIA0314GB
Name Not activated During pressure decreases
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
ABS IN valve Power supp ly is not supplied (open) Power supply is supplied (close)
ABS OUT valve Power supp ly is not supplied (close) Power supp ly is supplied (open)
Each brake caliper (fluid pressure) — Pressure decreases
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-20
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
SYSTEM
ABS Function Operating
(Pressure Increases)
Front RH brake caliper
• Brake fluid is supplied to the front RH brake caliper from the master cylinder through the cut valve 1 and the
ABS IN valve. Since the suction valve 1 and the ABS OU T valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the fr ont RH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
Front LH brake caliper• Brake fluid is supplied to the front LH brake caliper from the master cylinder through the cut valve 2 and the
ABS IN valve. Since the suction valve 2 and the ABS OU T valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the fr ont LH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
Rear RH brake caliper• Brake fluid is supplied to the rear RH brake caliper from the master cylinder through the cut valve 2 and the
ABS IN valve. Since the suction valve 2 and the ABS OU T valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the r ear RH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
Rear LH brake caliper
• Brake fluid is supplied to the rear LH brake caliper from the master cylinder through the cut valve 1 and the
ABS IN valve. Since the suction valve 1 and the ABS OU T valve is closed, the fluid does not flow into the
ALFIA0312GB
Name Not activated During pressure increases
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
ABS IN valve Power supply is not supplied (open) Power supply is not supplied (open)
ABS OUT valve Power supply is not supplied (close) Power supply is not supplied (close)
Each brake caliper (fluid pressure) — Pressure increases
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMBRC-21
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
reservoir. The amount of brake fluid supplied to the r ear LH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
Brake Release
Front RH brake caliper• Brake fluid is supplied to the front RH brake caliper through the return check valve of the ABS IN valve and
the cut valve 1, and returns to the master cylinder.
Front LH brake caliper• Brake fluid is supplied to the front LH brake caliper through the return check valve of the ABS IN valve and
the cut valve 2, and returns to the master cylinder.
Rear RH brake caliper• Brake fluid is supplied to the rear RH brake caliper through the return check valve of the ABS IN valve and the cut valve 2, and returns to the master cylinder.
Rear LH brake caliper• Brake fluid is supplied to the rear LH brake caliper through the return check valve of the ABS IN valve and
the cut valve 1, and returns to the master cylinder.
Component Parts and Function
ALFIA0315GB
Name Not activated During brake release
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
ABS IN valve Power supp ly is not supplied (open) Power supp ly is not supplied (open)
ABS OUT valve Power supp ly is not supplied (close) Power supply is not supplied (close)
Each brake caliper (fluid pressure) — Pressure decreases
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-22
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
SYSTEM
CONDITIONS FOR INDICATOR LAMP ILLUMINATION
• Turns ON when VDC and TCS functions are switched to
non-operational status (OFF) by VDC OFF switch.
• Turns ON when ignition switch turns ON and turns OF F when the system is normal, for bulb check purposes.
CONDITIONS FOR WARNING LAMP ILLUMINATION
Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
Component Function
Pump Returns the brake fluid reserved in reservoir to master cylinder by reducing pressure.
Motor Activates the pu mp according to signals from ABS actuator and el ectric unit (control unit).
Cut valve 1
Cut valve 2 Shuts off the ordinary brake line from master cylinder.
Suction valve 1
Suction valve 2 Supplies the brake fluid from master cylinder to the pump.
ABS IN valve Switches the fluid pressure line to increase or hold according to signals from control unit.
ABS OUT valve Switches the fluid pressure li ne to increase, hold or decrease according to si gnals from control unit.
Return check valve Returns the brake fluid from brake caliper to master cylinder by bypassing orifice of each valve when
brake is released.
Reservoir Temporarily reserves the brake fluid drained from brake caliper, so that pressure efficiently decreas-
es when decreasing pressure of brake caliper.
Pressure sensor Detects the brak e fluid pressure and transmits signal to ABS actuator and electric unit (control unit).
Condition (status) VDC OFF indicator lamp SLIP indicator lamp
Ignition switch OFF OFF OFF
For approx. 1 second after the ignition switch
is turned ON ON ON
Approx. 1 second after ignition switch is
turned ON (when the system is in normal op-
eration) OFF OFF
When VDC OFF switch is ON (VDC function
and TCS function are OFF) ON OFF
VDC function is malfunctioning OFF ON
TCS function is malfunctioning OFF ON
Condition (status) ABS warning lamp Brake warning lamp
Ignition switch OFF OFF OFF
For approx. 1 second after the ignition switch
is turned ON ON ON
Approx. 1 second after ignition switch is
turned ON (when the system is in normal op-
eration) OFF OFF
After engine starts OFF OFF
When parking brake operates (parking brake
switch ON) OFF ON
When brake fluid is less than the specified
level (brake fluid level switch ON) OFF ON
When vacuum sensor is malfunctioning OFF ON
VDC function is malfunctioning OFF OFF
TCS function is malfunctioning OFF OFF
ABS function is malfunctioning ON OFF
EBD function is malfunctioning ON ON
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMBRC-23
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
VDC/TCS/ABS : VDC FunctionINFOID:0000000009463753
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
• Side slip or tail slip may occur while driving on a slippery road or intending an urgent evasive driving maneu- ver. VDC function detects side slip status using each s ensor when side slip or tail slip is about to occur and
improves vehicle stability by brake c ontrol and engine output control during driving.
• In addition to ABS function, EBD function and TCS functi on, target side slip amount is calculated according
to steering operation amount from steering angle sensor. By comparing this information with vehicle side slip
amount that is calculated from information from yaw rate/side G sensor and wheel sensor, vehicle driving
conditions (conditions of understeer or oversteer) are judged and vehicle stability is improved by brake force
control on all 4 wheels and engine output control.
• VDC function can be switched to non-operational status (OFF) by operating VDC OFF switch. In this case,
VDC OFF indicator lamp turns ON.
• Control unit portion automatically improves driving st ability by performing brake force control as well as
engine output control, by transmitting drive signal to actuator portion according to difference between target
side slip amount and vehicle side slip amount
Brake limited slip differential (BLSD) function
is malfunctioning OFF OFF
VDC function is operating OFF OFF
TCS function is operating OFF OFF Condition (status) ABS warnin
g lamp Brake warning lamp
ALFIA0298GB
JSFIA0672GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-24
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
SYSTEM
• Brake force control function
at braking hard detects driver′s brake operations with the pressure sensor,
judges a brake booster ′s maximum brake power function by using information from the vacuum sensor, and
enhances more powerful braking force by controlling brakes of four wheels.
• VDC warning lamp blinks while VDC function is in operati on and indicates to the driver that the function is in
operation.
• CONSULT can be used to diagnose the system.
• Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function and TCS function. However, ABS functi on and EBD function operate normally. Refer to BRC-41,
"Fail-safe".
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
• During cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the outer
side of turn. Momentum is generated directing the vehicle toward the outer side of the turn. Oversteer is pre-
vented.
• Changing driving lane on a slippery road, when there may be a tendency to oversteer, engine output is con- trolled as well as brake force (brake fluid pr essure) of 4 wheels. Oversteer tendency decreases.
Component Signal description
ECM Transmits the following signals to ABS actuator and electric unit (control unit) via CAN commu-
nication.
• Acceleration pedal position signal
• Engine speed signal
• Target throttle position signal
TCM Transmits the current gear positi
on signal to ABS actuator and el ectric unit (control unit) via
CAN communication.
Steering angle sensor Transmits the steering angle sensor signal to ABS actuator and electric unit (control unit) via
CAN communication.
Combination meter Transmits the following signals to ABS actuator and electric unit (control unit) via CAN commu-
nication.
• Brake fluid level switch signal
• parking brake switch signal
Receives the following signals from ABS actuator and electric unit (control unit) via CAN com-
munication.
• VDC OFF indicator lamp signal
• SLIP indicator lamp signal
ALFIA0339GB
ALFIA0340GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM