check engine SSANGYONG MUSSO 2003 Service Manual
Page 593 of 1574
M162 ENGINE CONTROLS 1F1-61
Notice Replace the fuel pump relay if the measured value is over 9A.
Notice Check the fuel filter and fuel line when the fuel delivery is not within specified value.
Measure the Current Consumption of Fuel Pump
1. Remove the fuel pump relay from fuse and relay box in trunk, and turn the ignition switch to "ON" position.
2. Using a multi-tester, measure the current consumption by connecting the terminal No.1 and No.3 of pump.
Measure the Fuel Delivery From the Fuel Pump
1. Disconnect the return pipe from fuel distributor and insert
the appropriate hose into it.
2 . Place the hose end into the beaker with the minimum capacity of 1Liter.
3. Turn the ignition switch to "ON" position.
4. Connect the terminal No.33 and No.5 of ECU with a service wire.
5. Measure the fuel delivery from the fuel pump.
1Liter/max.35sec.
Specifed Value
5 - 9A
Specifed Value
Page 595 of 1574
M162 ENGINE CONTROLS 1F1-63
4. Remove the line to canister and measure the pressure withthe vacuum pressure gauge.
Test
1. Maintain the normal temperature and idling state by
operating the engine.
2. Connect the ECU terminal No.11 and No.34 and check for normal operation through the output waves using the
scanner. Notice
Test during purge control switchover valve operation after the minimum of 1 minute after the engine turned on.
3. Connect the ECU terminal No.34 and No.10 and check for current consumption during the ignition switch ON.
Purge switchover valve output wave
Specified Value0.3 - 0.5
Specified Value > 50mbar
(after approx. 1min.)
purge switchover valve operates at this time
Notice
Test while at normal temperature and at idling state by operating the engine.
Page 598 of 1574
1F1-66 M162 ENGINE CONTROLS Crankshaft Position Sensor Resistance Inspection
1. Disconnect the coupling "E" of ECU while the ignition switchis in "OFF" position.
2. Measure the resistance between the coupling terminal pin No.99 and No.100 using a multimeter. Notice Measure the insulator resistance of the crankshaft position sensor if out of the specified value.
Crankshaft Position Sensor Output Wave Inspection
1. Connect the test box to the ECU.
2. Measure the output wave between the ECU terminals No.99 and No.100 using the scanner or the oscilloscope while engine cranking (starter motor activated). Notice Check the segment or crankshaft position sensor and air gap if cannot get the output wave as shown in the figure.
Specified Value 1050 - 1400
Specified Value > 20k
Crankshaft Position Sensor Insulator Resistance Inspection
1. Disconnect the engine coupling from ECU while the ignition
switch is in "OFF" position.
2. Measure the resistance between the coupling terminal pin No.100 and No.69. Notice Measure the check and ground terminal of the crankshaft position sensor if out of the specified value.
Page 599 of 1574
M162 ENGINE CONTROLS 1F1-67
CAMSHAFT POSITION SENSOR
1 Bolt (M6 X 14)......................................... 9-11Nm
2 Camshaft Position Sensor
Removal & Installation Procedure
1. Disconnect the wiring connector from the camshaft position sensor.
2. Unscrew the bolt (2) and remove the camshaft position sensor. Installation Notice 3 Shim
5 O-ring
Tightening Torque 9 - 11 Nm
3. Check the clearance and replace the shim if necessary.
4. Check the O-ring for damage and replace it if necessary.
5. Installation should follow the removal procedure in the
reverse order.
Page 600 of 1574
1F1-68 M162 ENGINE CONTROLS Camshaft Position Sensor Power Supply Inspection
1. Turn the ignition switch to 'ON' position.
2. Disconnect the camshaft position sensor connector.
3. Measure the voltage between the No.1 and No.3 pin ofcamshaft position sensor while the ignition switch is in "ON" position. Notice If the measured value is not within the specified value, check the cable.
Notice The signal voltage will be changed in the range of 1.2 -
1.7V.
Camshaft Position Sensor Output Wave Inspection
1. Connect the test box to the ECU.
2. Measure the output wave between the ECU terminal No.104 and No.106 using the scanner or the oscilloscope while the engine speed is at idle. Notice Replace the camshaft position sensor if cannot get the output wave as shown in the figure.
Specified Value 11 - 14 V
Specified Value 1.2 - 1.7 V
Camshaft Position Sensor Signal Voltage Inspection
1. Connect the test box to the ECU.
2. Measure the voltage between the ECU terminal No.11 andNo.106 while the engine speed is at idle.
Page 607 of 1574
M162 ENGINE CONTROLS 1F1-75
COOLANT TEMPERATURE SENSOR
1 Artificial Resin Housing
2 Metal Housing
3 NTC (negative temperature coefficient) Resistor
Removal & Installation Procedure
1. Remove the pressure by opening the pressure cap in the coolant subtank.
2. Disconnect the connector and remove the coolant temperature sensor. Installation Notice Replace the seals with new one.
3. Installation should follow the removal procedure in the reverse order.
4. Check for leaks at each connections after starting the engine. 4 Connector
5 Coolant Temperature Sensor
Tightening Torque 18 - 22 Nm
Page 615 of 1574
1F3-4 OM600 ENGINE CONTROLS
FUEL TANK
1 Fuel Tank
2 The Sender of Fuel Tank
3 2-way Check Valve
4 Pre Filter
5 Front Fuel Filler Neck
6 Rear Fuel Filler Neck
7 Fuel Supply Tube 8 Fuel Return Tube
9 Filter Hose
10 Fuel Tank Hose
11 Fuel Filler Cap
12 Clip
13 Clip
Page 616 of 1574
OM600 ENGINE CONTROLS 1F3-5
VACUUM CONTROL SYSTEM TEST
2 Engine Cut-Off Valve (Ignition Key Switch)
3 Auto-locking Hub Solenoid Valve
4 Engine Stop Valve Unit
5 PLA Vacuum Unit (Idle Speed Adjustment)
6 Engine
7 Vacuum Pump830
° Thermovalve
9 Fuel Injection Pump
10 Filter with Restriction
11 Check V alve
12 Modulating Pressure Line (Automatic T/M)
Test Data
Idle Speed Increase Permissible Pressure Drop of System At least 100 rpm at approx. 500mbr
400 - 500mbar approx. 1 min.
Page 622 of 1574
1F3-12 OM600 ENGINE CONTROLS
Test Procedure
1. Remove the fuel filter (1) and keep the filter not to be damaged from running engine.
2. Remove the vacuum line (2) from ancillaries connection (3).
3. Connect the vacuum tester (4) to the ancillaries connection (3).
Vacuum Tester 201 589 13 21 00
4 Run the engine at idle and check vacuum pressure after 30 sec. Notice If out of standard, replace the vacuum pump.
5. Remove the vacuum tester.
6. Connect the vacuum line to the ancillaries connection.
7. Install the fuel filter.
Standard > 70 mbar
Page 626 of 1574
1F3-16 OM600 ENGINE CONTROLSIdle Speed
750 - 850 rpm 720 - 820 rpm
EngineOM661LA EngineOM662LA Engine
Tools Required 667 589 00 21 00 TDC Pulse Generato
Commercial Tool
IDLE SPEED ADJUSTMENT Service Data
e.g. Bosch, MOT 001.03
Sun, DIT 9000
Digital Tester
Adjustment Procedure
1. Connect the digital tester (1) and TDC pulse sender unit
(11).
2. Run the engine and warm up the coolant to 60~80 °C.
TDC pulse generator 667 589 02 21 00
3. Disconnect the vacuum hose (4) from the PLA unit to check idle speed with tester.
4. Check idle speed with tester.
Notice
To adjust idle speed, loosen the locking nut (6) of PLA unit.
OM 661LA Engine 750 - 850rpm
OM 662LA Engine
720 - 820rpm