lock FORD FIESTA 2007 Workshop Manual

303-05-1 9 Accessory Drive 303-05-1 9
REMOVAL AND INSTALLATION
4. Install the belt around the installation tool.
Install the belt guide tool (supplied in the
parts kit) to the accessory drive belt (shown
I from above for clarity).
5. Make sure that the accessory drive belt is
correctly positioned in the grooves of the
pulleys.
8. Install the belt guide tool to the generator
6. N0TE:Only turn the engine in the normal mounting
bracket.
direction of rotation.
N0TE:Guide the accessory drive belt onto the
pulleys as the engine is rotated.
Turn the engine until the paint mark is at the
8 o'clock position.
9.
N0TE:Only turn the engine in the normal
direction of rotation.
N0TE:Guide the accessory drive belt onto the
pulleys as the engine is rotated.
Turn the engine until the paint mark is at the
7. N0TE:The curved end of the tool fits around 3 o'clock position
the belt and the cranked end of the tool fits
around the generator mounting bracket.
10. Remove the installation tool from the
crankshaft pulley.
2006.0 Fiesta 1212006 GI 46274en
procarmanuals.com

303-05-20 Accessory Drive 303-05-20
REMOVAL AND INSTALLATION
11. N0TE:Only turn the engine in the normal N0TE:Guide the power steering pump belt onto
direction of rotation. the pulleys as the engine is rotated. (.
Turn the engine through 360 degrees. Turn
the engine until the tool is at the 9
12.
Check that the accessory drive belt is o'clock
position.
correctly positioned in the grooves of the
pulleys.
Repeat the installation procedure if the
accessory drive belt is misaligned.
13. Remove the belt guide tool from the
accessory drive belt.
Discard the belt guide tool.
14. lnstall the installation tool to the crankshaft
pulley at the
12 o'clock position.
18. Remove the installation tool from the
crankshaft pulley.
19. N0TE:Only turn the engine in the normal
direction of rotation.
Turn the engine through
360 degrees.
20. Check that the power steering pump belt
is correctly positioned in the grooves of
the pulleys.
I I Repeat the installation procedure if the power
15. lnstall the power steering pump belt. steering pump belt is misaligned.
Discard the installation tool.
1. lnstall the power steering pump belt around
the power steering pump pulley.
21. Install the crankshaft pulley splash shield.
2. lnstall the power steering pump belt around
the installation tool.
16. Make sure that the power steering pump
belt is correctly positioned in the grooves
of the pulleys.
17. N0TE:Only turn the engine in the normal
direction of rotation.
22. Lower the vehicle.
- --
2006.0 Fiesta 1212006 GI 46274en
procarmanuals.com

303-05-21 Accessory Drive 303-05-21
REMOVAL AND INSTALLATION
Accessory Drive Belt - 1.4L Duratec-I 6V (Sigma)/l .6L
Duratec-1 6V (Sigma), Vehicles Without: Air
Conditioning(21 567 0)
General Equipment 2. Using paint or typing correction fluid, mark
Knife the crankshaft pulley at the 6 o'clock
position.
Removal
A CAUTI0N:The accessory drive belt must
not be reused as it is designed to be
stretched onto the pulleys only once.
Failure to follow this instruction may lead
to premature failure of the belt.
1. Raise and support the vehicle. For additional
information, refer to Section
I 00-02 [Jacking
and Lifting].
2. Detach the power steering line and remove
the crankshaft pulley splash shield.
3. lnstall the installation tool (supplied in the
parts kit) to the crankshaft pulley at the
6
o'clock position.
3. Using a suitable knife, cut the accessory
drive belt and remove.
Installation 4. lnstall the accessory drive belt.
NOTE:
lnstall a new accessory drive belt. 1. lnstall the belt around the generator pulley.
2. lnstall the belt around the power steering
1. Wipe clean all of the pulleys to make sure pump pulley.
that the accessory drive belt does not slip 3. Install the belt around the water pump pulley.
during installation.
2006.0 Fiesta 1212006 Gl49874en
procarmanuals.com

303-05-22 Accessory Drive 303-05-22
REMOVAL AND INSTALLATION
4. Install the belt around the installation tool. Install the belt guide tool (supplied in the
parts kit) to the accessory drive belt (shown
from above for clarity).
5. Make sure that the accessory drive belt is
correctly positioned in the grooves of the
pulleys.
8. Install the belt guide tool to the generator
6. N0TE:Only turn the engine in the normal mounting
bracket.
direction of rotation.
N0TE:Guide the accessory drive belt onto the
pulleys as the
e'ngine is rotated.
Turn the engine until the paint mark is at the
8 o'clock position.
9. N0TE:Only turn the engine in the normal
direction of rotation.
N0TE:Guide the accessory drive belt onto the
pulleys as the engine is rotated.
Turn the engine until the paint mark is at the
7. N0TE:The curved end of the tool fits around 3 o'clock position
the belt and the cranked end of the tool fits
around the generator mounting bracket.
10. Remove the installation tool from the
crankshaft pulley.
2006.0 Fiesta 1212006 Gl49874en
procarmanuals.com

303-05-24 Accessory Drive 303-05-24
REMOVAL AND INSTALLATION
Power Steering Pump Belt - 1.4L Duratec-1 6V (Sigma)/l .6L
Duratec-1 6V (Sigma), Vehicles With: Air
Conditioning(21 567 0)
General Equipment 2. Install the installation tool (supplied in the
Knife parts kit) to the crankshaft pulley at the 12
o'clock position.
Removal
A CAUTI0N:The power steering pump belt
must not be reused as it is designed to be
stretched onto the pulleys only once.
Failure to follow this instruction may lead
to premature failure of the belt.
1. Raise and support the vehicle. For additional
information, refer to Section
100-02 [Jacking
and Lifting].
2. Detach the power steering line and remove
the crankshaft pulley splash shield.
3. Install the power steering pump belt.
I. Install the belt around the power steering
pump pulley.
2. Install the belt around the installation tool. (
Installation
4. Make sure that the power steering pump belt
N0TE:lnstall a new power steering pump belt. is correctly positioned in the grooves of the
1. Wipe clean both of the pulleys to make sure pulleys.
that the power steering pump belt does not
5. N0TE:Only turn the engine in the normal
slip during installation.
direction of rotation.
N0TE:Guide the power steering pump belt onto
the pulleys as the engine is rotated.
2006.0 Fiesta 1212006 GI 00708en
procarmanuals.com

303-05-25 Accessory Drive 303-05-25
REMOVAL AND INSTALLATION
Turn the engine until the installation tool is
at the
9 o'clock position.
i
6. Remove the installation tool from the
crankshaft pulley.
7. N0TE:Only turn the engine in the normal
direction of rotation.
Turn the engine through
360 degrees. 1
8. Check that the power steering pump belt is
correctly positioned in the grooves of the
pulleys.
i Repeat the installation procedure if the power
steering pump belt is misaligned.
Discard the installation tool.
9. Install the crankshaft pulley splash shield.
10. Lower the vehicle.
2006.0 Fiesta 1212006 GI 00708en
procarmanuals.com

303-05-26 Accessory Drive 303-05-26
REMOVAL AND INSTALLATION
Accessory Drive Belt - 2.OL Duratec-HE (M14)(21 567 0)
Removal 4. Remove the accessory drive belt.
I. Disconnect the battery ground cable. 1. Rotate the accessory drive belt tensioner
For additional information, refer to: Battery counterclockwise.
Disconnect
(41 4-01 Battery, Mounting and 2. Remove the accessory drive belt.
Cables,
~eneral procedures).
-
2. Raise and support the vehicle.
For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
and Operation).
3. Remove the crankshaft pulley splash shield.
2006.0 Fiesta 1212006 G421384en
procarmanuals.com

Engine Emission Control - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-I 6V (Sigma)
DIAGNOSIS AND TESTING
Engine Emission Control
lnspection and Verification
1. Verify the customer concern.
2. Visually inspect for obvious signs of mechanical
damage.
3. If an obvious cause for an observed or reported
Visual lnspection Chart
I 1 concern is found, correct the cause (if possible)
I Mechanical I before proceeding to the next step.
. -
Symptom Chart
Positive crankcase ventilation (PCV) valve
PCV separator
Symptom Chart
Symptom
Excessive crankcase pressure
4. If the cause is not visually evident, verify the
symptom and refer to the Symptom Chart.
Oil in the air intake system Possible
Sources
Blocked PCV valve.
Blocked PCV separator.
Blocked PCV hose.
Restriction in PCV separator.
PCV valve permanently open. Action
CLEAN
or INSTALL new PCV
components as necessary.
TEST the system for normal
operation. If the concern
persists, REFER to
Section 303-00 [Engine
System
- General Information].
CLEAN or INSTALL a new
PCV separator. TEST the
system for normal operation.
-
INSTALL a new PCV valve.
TEST the system for normal
operation.
2006.0 Fiesta 1212006 Gl48220en
procarmanuals.com

Engine Emission Control - 2.OL Duratec-HE
303-08B-4
(MI41 303-08B-4
DESCRIPTION AND OPERATION
Item Description two hoses. One PCV hose connects the PCV valve
to the intake manifold, the other PCV hose
2
3
The positive crankcase ventilation (PCV) system
consists of a valve mounted in the crankcase vent
oil separator (attached to the cylinder block) and
connects the valve cover to the air cleaner. 1
4
2006.0 Fiesta 1212006 G37563en
Positive crankcase ventilation (PCV) valve
PCV hose
Crankcase vent oil
se~arator
Under idle and part throttle conditions, the
crankcase vapor flows through the intake manifold
Crankcase vent oil separator retaining
bolt into the combustion chambers where the vapor is
burnt during combustion.
procarmanuals.com

Engine Emission Control - 2.OL Duratec-HE
303-08B-6
(MI41 303-08B-6
DIAGNOSIS AND TESTING
Engine Emission Control
lnspection and Verification
General Equipment Visual Inspection Chart L..
I. Verify the customer concern.
2. Visually inspect for obvious signs of mechanical
or electrical damage.
Worldwide Diagnostic System
(WDS)
- Hose(s)/hose joints
- Gasket(s)
- Positive crankcase
ventilation (PCV)
valve
- PCV separator
Mechanical
- Exhaust gas recircu-
lation (EGR) valve
Electrical
- Electrical
con
nector(s)
- Wiring harness
- Fuse(s)
- Relay
- EGRvalve
- Powertain control
module (PCM)
3. If an obvious cause for an observed or reported
concern is found, correct the cause (if possible)
before proceeding to the next step.
4. If the concern is not visually evident, verify the
symptom and refer to the Symptom Chart.
Symptom Chart
Symptom Chart
Symptom Possible Sources Action
I
Poor engine performance EGR valve.
Using WDS, CHECK the EGR
Valve Duty Cycle input signal
I to the EGR vacuum regulator
valve. If the result is 0%,
REMOVE the EGR valve.
REFER to Exhaust Gas Recir-
culation (EGR) Valve
- in this
section.
INSPECT the EGR valve and
valve seat for damage. Make
sure that the EGR valve is in
the closed position. If the EGR
valve is not closed. INSTALL
a
new EGR valve. TEST the
system for normal operation. If
the result is not 0% continue
the engine diagnostic using
WDS.
2006.0 Fiesta 1212006 G334290en
Excessive crankcase pressure Blocked or damaged PCV
hose(s).
Blocked crankcase vent oil
separator. CHECK
the PCV system
components for blockages, CLEAN or INSTALL new
components as necessary.
procarmanuals.com