GEELY CK 2008 Workshop Manual

2342Check the voltage between terminals under each operating condition as shown in the table below.
Abnormal:Repair or replace wire harness and connector
Normal:Check and replace radio assembly
10. Power coming in, but CD player not operating.
(1) Press CD player "OPEN" to see if CD ejects.
No CD does not eject for inspection after being inserted
Yes Check if the right CD is inserted
(2) Check if the proper CD is inserted
1Check if the proper CD is inserted
2Make sure the working CD is music and it is not distorted, cracked, dirty, scratched or defected.
Standard: Working music CD
Description:
Semi-transparent CD or CD of strange shape can not be played.
Music CD recorded in PC CD-ROM and recorded CD-R can not be played.
Adapter is not needed to play 8cm CD.
Abnormal:There is something wrong with CD
Normal:Check and insert a proper CD
(3) Check and insert a proper CD
1Check and insert a proper CD.
2Check if CD is installed in reverse order.
Standard: No
Abnormal:Install the disc correctly
Normal:Clean the discTeste r Connec tion Condition Sta nda rd Sta tus
+B - GND Consta nt Status 10～
14V
ACC - GND Ignition switch ACC or ON 10～
14V

235(4) Replace it with another CD and re-check.
yReplace the faulty CD with working CD to see if the same fault re-occurs.
Standard: The fault is cleared
Abnormal:There is something wrong with CD
Normal:Check if the radio auto-research function works
(5) Check if the radio auto-research function works
yPerform the radio auto-research function
Standard: The fault is cleared.
Abnormal: Go to Step (9)
Normal:Has sudden temperature change occurred inside vehicle?
(6) Has sudden temperature change occurred inside vehicle?
yCheck if sudden temperature change has occurred inside vehicle
Standard: Sudden temperature change has occurred inside vehicle.
Description:
Formulation of dew condensation inside the CD player is due to temperature changes. CD may not play.
Normal:Formulation of dew condensation due to temperature changes (Leave it for a while before
using it)
Abnormal:Check the signal wire between the radio and disc box
(7) Check the signal wire for short circuit or open circuit.
Yes Replace the signal wire
No Replace the disc box
(8) Replace the disc box
Standard: The faulty is cleared
Normal:Box faulty
Abnormal:Check the radio assembly (+B, ACC, GND)
(9) Check the radio assembly (+B, ACC, GND)
1Check the continuity between terminals under each operating condition as shown in the table below.
Standard:
2Check the voltage between terminals under each operating condition as shown in the table below.
Standard:Teste r Connec tion Condition Sta nda rd Sta tus
+B - GND Consta nt Status 10～
14V
ACC - GND Ignition switch ACC or ON 10～
14VTester connection Condition Standard Status
GND Consta nt Status Continuity

236Abnormal:Repair or replace wire harness and connector
Normal:Check and replace radio assembly
11. Sound quality poor only when playing CD (Volume faint)
(1) Replace it with another CD and re-check
Normal: CD failure
Abnormal:Replace the disc box
(2) Replace the disc box
Normal:Box damaged
Abnormal:Check and replace radio assembly
12.CD sound jump
(1) Disc cleaning
yIf the disc gets dirty, clean the disc by wiping the surface from the center to outside in the radial directions
with a soft cloth.
Notice:
Do not use a conventional record cleaner or anti--static preservative.
Standard: The fault is cleared.
Normal:The disc is dirty
Abnormal:Replace it with another CD and re-check.
(2) Replace it with another CD and re-check.
Standard: The fault is cleared.
Normal: CD failure
Abnormal:Check when it will happen
(3) Check when it will happen
yCheck where sound jump will happen
Standard: Drive on bumpy road
Normal:Replace CD box
Abnormal:Compare with other vehicles of the same model
(4) Compare with other vehicles of the same model
yCompare with other vehicles of the same model of no fault. Check for any difference when faulty
occurs.
Standard: No difference is found.
Normal:Make sure there is no difference
Abnormal:Check CD box installation
(5) Check CD box installation
yCheck CD box installation

237Standard: Installation correct
Abnormal:Install CD box correctly
Normal: Has suddentemperature change occurs inside the disk cabin?
(6) Has sudden temperature change occurs inside the disk cabin?
yCheck if sudden temperature change occurs inside the disk cabin?
Standard: Sudden temperature change occurs inside the disk cabin.
Description:
Formulation of dew condensation inside the CD player is due to temperature changes. CD may not play.
Normal:Formulation of dew condensation due to temperature changes (Leave it for a while before
using it)
Abnormal:Check and replace CD box

238Section 4 Audio and Video System ReplacementI. Notice on operationPlease explain to the customer that the AM/FM broadcast channel information will be cleared when remov-
ing the battery negative terminal cable. Record the channel information before removing the negative termi-
nal cable if necessary. Reset after connecting the negative terminal cable.
yAll cassette tapes and CDs must be taken out before radio removal and installation.
yIf the cassette tapes and CDs can not be taken out due to radio fault. Do not take them out by force.
Drive the vehicle to Service Station.
yMake sure the grounding bolts are tightened before antenna removal and installation.
yThere will be noise when receiving electric wave if the grounding bolts are not tightened.
yDon't touch the speaker cone.Intermediate Multiple CD main unit Radio assemblyInstrument PanelMultiple DVD main unit

239Tweeter Antenna
CableAntenna
AssemblyFront Speaker AssemblyRear Speaker Assembly

240II. Radio assembly1. Remove the intermediate instrument panel (See interior trim)
2. Remove the radio assembly
1Remove 4 bolts
2Disconnect connectorIII. Front speaker assembly1. Remove front outside rear view mirror cover
2. Remove door handle
3. Remove the front door power window switch assembly
4. Remove the front door inside trim plate assembly
5. Remove the front door five-inch speaker assembly
1Disconnect connector
2Remove 4 self tapping screw and speaker assemblyIV. Tweeter speaker assembly1. Remove front outside rear view mirror cover
2. Remove tweeter speaker assembly
1 Disconnect connector
2Remove 2 self tapping screw and speaker assemblyV. Rear speaker assembly1. Remove rear speaker baffle
2. Remove rear speaker assembly
1 Disconnect connector
2Remove 4 self tapping screw and rear speaker assemblyVI. Remove antenna cable1. Remove the roof interior trim
2. Remove A-pillar trim plate
3. Disconnect connector
4. Remove instrument panel
5. Remove 4 clips and antenna cable

241VII. Overhead antenna assembly1. Remove the roof interior trim
2. Disconnect connector
3. Remove antenna nut
4. Remove the overhead antenna assemblyVIII. CD, DVD1. Remove the left side rear trunk interior trim
2. Disconnect connector
3. Remove 4 bolts and disc box

242Chapter 7
SRS (Supplemental Restraint System)Section 1 SRS-General InformationI. PRECAUTIONFor safe reasons, read the following precautions before starting any operation.
1. When servicing the SRS, correct sequence and items are described in the following chapter.
2. Instruments and special tools recommended in this chapter shall be used for operation.
3. When servicing the following components, replace them with the new ones if there is a failure.
(1) SRS ECU
(2) Clock Spring Module
(3) Driver Airbag Module
(4) Passenger Airbag Assembly (Option)
4. If there is any abnormality in the wire harness of the SRS, replace it with a new one. Correct or replace the
abnormal wire harness in accordance with Table 1.
Figure 1 (Table 1)No De signation De scription
1 Belt-pretensioner, Driver, Low Seat belt pretensioner, driver side, low position
2 Belt-pretensioner, Driver, High Seat belt pretensioner, driver side, high position
3 Belt-pretensioner, Passenger, High Seat belt pretensioner, passenger side, high position
4 Belt-pretensioner, Passenger, Low Seat belt pretensioner, passenger side, low position
5 IGN Battery voltage
6 GND Ground-ground w ire
7 WL Airbag w arning light
9 K Diagnostic serial data I/O (K line)
10 DAB Hi Driver airbag, high positionE C U T e r mina l D e s c r ipt ion

2435. Servicing operation shall be carried out 60s after the negative
(-) terminal cable is disconnected from the battery. In addition,
the disconnected negative (-) terminal cable shall be protected
with insulating tape for insulation.
In order to deploy an airbag within a certain time period after the
battery is disconnected, condenser in the ECU shall retain some
electrical energy. Otherwise, it could lead to a serious accident
because of the unexpected deployment of airbag.
6. During spray paint work, ECU, airbag assembly, clock spring
assembly, etc shall be removed and kept in place to avoid the effects of overheat. (Over 93¡æ)
7. When the SRS is serviced, a diagnostic scan meter is used to clear the DTC to enable the normal work of
the warning light.1 1 D AB Lo D r iv er a ir b ag , lo w p o s it io n
13 (Option) PAB Hi Passenger airbag, high position
14 (Option) PAB Lo Passenger airbag, low position
20Passenger Airbag Deactivation
Indic atorPassenger airbag deac tivation indic ator light
27PPD/ Passenger Airbag
Deac tivation Sw itch, HighPassenger airbag deac tivation sw itc h, high position
30 Crash Output Crash outputInsulating TapeBatteryCableDriver Side
Warning LampPassenger Side
Warning LampDriver Seat Inflation
Element & AirbagCrash Sensor &
Diagnostic ModuleFront/RH Inflation
Element & Airbag