INFINITI QX4 2001 Factory Service Manual

OverhaulNBBT0006IFor removal of door trim, refer to ªDOOR TRIMº (BT-30).
IAfter adjusting door or door lock, check door lock operation.
SBT512-B
FRONT DOOR
Overhaul
BT-18

Front Door Limit Switch ResetNBBT0027RESET CONDITIONSNBBT0027S01After each of the following operations are performed, reset the limit
switch (with built-in motor).
IRegulator removal and installation
IRemoval of motor from regulator
IOperation of regulator as a single unit
IDoor glass removal and installation
IGlass run removal and installation
SBT041A
RESET PROCEDURESNBBT0027S02After installing parts, proceed as follows:
1. Close the door window completely.
2. Press the reset switch and open the door window completely.
3. Release the reset switch. After making sure the reset switch
has returned to the original position, close the door window
completely.
4. The limit switch is now reset.
CAUTION:
Be sure to manually open or close the door window. (Do not
use the automatic open-close procedures.)
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
FRONT DOOR
Front Door Limit Switch Reset
BT-19

OverhaulNBBT0007
SBT736
REAR DOOR
Overhaul
BT-20

Removal and InstallationNBBT0008CAUTION:
IDisconnect both battery cables in advance.
IDisconnect air bag system line in advance.
INever tamper with or force air bag lid open, as this may
adversely affect air bag performance.
IBe careful not to scratch pad and other parts.
SBT042A
*1 RS-17 *2 BT-28
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
BT-21

SBT043A
*2 BT-28 *3 RS-19
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-22

SBT038A
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-23

SBT039A
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-24

SBT029A
Steering column cover
After removing the screws, release the pawls by pressing on the
upper cover where it meets (the bottom cover) from both sides.
SBT030A
Instrument lower panel on the driver side
Open the pocket after removing the screws. Hold the opening and
the bottom and pull out horizontally.
SBT044A
Cluster lid A
After removing the screws, hold the bottom and pull out.
CAUTION:
Cover the surroundings with a cloth to prevent damage.
SBT031A
Center ventilator
Hook a cloth-covered flat-bladed screwdriver into the right-side
groove section, and pull out.
CAUTION:
To prevent the screwdriver from slipping and causing damage
to the surface, pull out while applying pressure on the screw-
driver towards the right.
SBT045A
Cluster lid C
After removing the screws, place hands on the metal clip section,
and pull forward to remove the metal clips.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-25

SBT040A
Console finisher
1) Open the lid of the cup holders, insert a cloth-covered flat-
bladed screwdriver into the gap between the console and the
finisher, and remove the clip at the back.
2) Lift up the metal clip section, and pull forward to remove.
SBT033A
Console box
1) Pull up the parking brake lever.
2) Remove the screws, pull the console towards the back of the
car until it is free of the instrument panel, lift up the front and
remove.
IIt will be easier to remove if the parking brake lever is pulled
up for more than 10 notches.
SBT034A
Instrument finisher
Remove the screws and pull up.
SBT046A
Instrument lower panel on the passenger side
After removing the screws, hold both sides and pull out horizontally.
SBT047A
Instrument mask
Insert a cloth-covered flat-bladed screwdriver, and remove by lift-
ing up.
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-26

SBT035A
Defroster grille
REMOVAL
Insert a cloth-covered flat-bladed screwdriver into the grilles of the
outside, center and central grilles, respectively, lift up the front of
the grilles and remove.
INSTALLATION
After inserting the front section, insert the rear section (pawls) to
attach.
CAUTION:
Confirm that the pawls at the rear are securely attached.
SBT036A
Side ventilator-left
Insert a cloth-covered flat-bladed screwdriver into the lower
section, and pull out forward.
SBT037A
Side ventilator-right
Insert a cloth-covered flat-bladed screwdriver into the corner of the
lower section, and pull out forward. (Securely press the screwdriver
against the ventilator.) Or, after removing the instrument lower
panel, push the ventilator out from the back.
Side defroster grille
After removing the side ventilator, reach in with hands from the
opening, push on the pawls from behind the grille, and remove by
pushing out.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
BT-27