turn signal INFINITI QX56 2011 Factory User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 76 of 5598
POWER SUPPLY AND GROUND CIRCUITADP-67
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
POWER SUPPLY AND GROUND CIRCUIT
DRIVER SEAT CONTROL UNIT
DRIVER SEAT CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006248353
1.CHECK FUSE
Check that the following fuse and fusible link are not fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2.CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK DRIVER SEAT CONTROL UNIT GROUND CIRCUIT
Check continuity between the driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace harness.
DRIVER SEAT CONTROL UNIT : Special Repair RequirementINFOID:0000000006248354
1.PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to ADP-51, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL : Description".
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
AUTOMATIC DRIVE POSITIONER CO NTROL UNIT : Diagnosis Procedure
INFOID:0000000006248355
NOTE:
Do not disconnect the battery negative terminal and the dr iver seat control unit connector until DTC is con-
firmed with CONSULT-III.
1.CHECK FUSE
Check that the following fuse and fusible link are not fusing.
Signal name Fuse No.
Battery power supply K (50 A)
(+) (-)Voltage (V)
(Approx.)
Driver seat control unit
Connector Terminals B451 33 Ground Battery voltage
Driver seat control unit GroundContinuity
Connector Terminal
B451 43 Existed
Revision: 2010 May2011 QX56
Page 77 of 5598
ADP-68
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2.CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check voltage between automatic drive posit ioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK AUTOMATIC DRIVE POSITION ER CONTROL UNIT GROUND CIRCUIT
Check continuity between the automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace harness.
AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Special Repair Requirement
INFOID:0000000006248356
1.PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to ADP-51, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL : Description".
Signal name Fuse No.
Battery power supply K (50 A)
(+) (-)Voltage (V)
(Approx.)
Automatic drive positioner control unit
Connector Terminals M104 25 Ground Battery voltage
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M104 30 Existed
Revision: 2010 May2011 QX56
Page 78 of 5598
SLIDING SWITCHADP-69
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SLIDING SWITCH
Component Function CheckINFOID:0000000006248357
1.CHECK FUNCTION
1. Select “SLIDE SW-FR”, “SLIDE SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check sliding switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-69, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248358
1.CHECK SLIDING SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK SLIDING SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
SLIDE SW-FR Sliding switch (forward) Operate ON
Release OFF
SLIDE SW-RR Sliding switch (backward) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 8
Ground 12
24
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 8
B459 8
Existed
24 24
Driver seat control unit GroundContinuity
Connector Terminal
B452 8
Not existed
24
Revision: 2010 May2011 QX56
Page 80 of 5598
RECLINING SWITCHADP-71
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
RECLINING SWITCH
Component Function CheckINFOID:0000000006248360
1.CHECK FUNCTION
1. Select “RECLN SW-FR”, “RECLN SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check reclining switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-71, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248361
1.CHECK RECLINING SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK RECLINING SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
RECLINE SW-FR Reclining switch (forward)Operate ON
Release OFF
RECLINE SW-RR Reclining switch (backward) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 9
Ground 12
25
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 9
B459 9
Existed
25 25
Driver seat control unit GroundContinuity
Connector Terminal
B452 9
Not existed
25
Revision: 2010 May2011 QX56
Page 82 of 5598
LIFTING SWITCH (FRONT)ADP-73
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
LIFTING SWITCH (FRONT)
Component Function CheckINFOID:0000000006248363
1.CHECK FUNCTION
1. Select “LIFT FR SW-UP”, “LIFT FR SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check lifting switch (front) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-73, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248364
1.CHECK LIFTING SWITCH (FRONT) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK LIFTING SWITCH (FRONT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
LIFT FR SW-UP Lifting switch front (up) Operate ON
Release OFF
LIFT FR SW-DN Lifting switch front (down) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 10
Ground 12
26
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 10
B459 10
Existed
26 26
Driver seat control unit GroundContinuity
Connector Terminal
B452 10
Not existed
26
Revision: 2010 May2011 QX56
Page 84 of 5598
LIFTING SWITCH (REAR)ADP-75
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
LIFTING SWITCH (REAR)
Component Function CheckINFOID:0000000006248366
1.CHECK FUNCTION
1. Select “LIFT RR SW-UP”, “LIFT RR SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check lifting switch (rear) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-75, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248367
1.CHECK LIFTING SWITCH (REAR) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK LIFTING SWITCH (REAR) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
LIFT RR SW-UP Lifting switch rear (up) Operate ON
Release OFF
LIFT RR SW-DN Lifting switch rear (down) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 11
Ground 12
27
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 11
B459 11
Existed
27 27
Driver seat control unit GroundContinuity
Connector Terminal
B452 11
Not existed
27
Revision: 2010 May2011 QX56
Page 86 of 5598
TILT SWITCHADP-77
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
TILT SWITCH
Component Function CheckINFOID:0000000006248369
1.CHECK FUNCTION
1. Select “TILT SW-UP”, “TILT SW-DOWN” in “Data monitor” mode with CONSULT-III.
2. Check tilt switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-77, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248370
1.CHECK TILT SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect tilt & telescopic switch connector.
3. Turn ignition switch ON.
4. Check voltage between tilt & telesc opic switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK TILT SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
Monitor item Condition Status
TILT SW-UP Tilt switch (up) Operate ON
Release OFF
TILT SW-DOWN Tilt switch (down) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Tilt & telescopic switch
Connector Terminals
M102 2
Ground 5
3
Automatic drive positioner control unit Tilt & telescopic switch Continuity
Connector Terminal Connector Terminal
M75 1
M102 2
Existed
13 3
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M75 1
Not existed
13
Revision: 2010 May2011 QX56
Page 88 of 5598
TELESCOPIC SWITCHADP-79
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
TELESCOPIC SWITCH
Component Function CheckINFOID:0000000006248372
1.CHECK FUNCTION
1. Select “TELESCO SW-FR”, “TELESCO SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check telescopic switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-79, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248373
1.CHECK TELESCOPIC SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect tilt & telescopic switch connector.
3. Turn ignition switch ON.
4. Check voltage between tilt & telesc opic switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK TELESCOPIC SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
Monitor item Condition Status
TELESCO SW-FR Telescopic switch (forward) Operate ON
Release OFF
TELESCO SW-RR Telescopic switch (backward) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Tilt & telescopic switch
Connector Terminals
M102 5
Ground 5
4
Automatic drive positioner control unit Tilt & telescopic switch Continuity
Connector Terminal Connector Terminal
M75 7
M102 5
Existed
19 4
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M75 7
Not existed
19
Revision: 2010 May2011 QX56
Page 90 of 5598
SEAT MEMORY SWITCHADP-81
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SEAT MEMORY SWITCH
Component Function CheckINFOID:0000000006248375
1.CHECK FUNCTION
1. Select “MEMORY SW 1”, “MEMORY SW 2”, “SET SW” in “Data monitor” mode with CONSULT-III.
2. Check seat memory switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-81, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248376
1.CHECK SEAT MEMORY SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect seat memory switch connector.
3. Turn ignition switch ON.
4. Check voltage between seat memory switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK SEAT MEMORY SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control unit harness connector and seat memory switch harness
connector.
4. Check continuity between driver s eat control unit harness connector and ground.
Monitor item Condition Status
MEMORY SW 1 Memory switch 1 Push ON
Release OFF
MEMORY SW 2 Memory switch 2 Push ON
Release OFF
SET SW Set switch Push ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Seat memory switch
Connector Terminals
D13 1
Ground 5
2
3
Driver seat control unit Seat memory switch
Continuity
Connector Terminal Connector Terminal
B452 6
D13 2
Existed
22 1
28 3
Revision: 2010 May2011 QX56
Page 92 of 5598
DOOR MIRROR REMOTE CONTROL SWITCHADP-83
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Comp onent Function CheckINFOID:0000000006248378
1.CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to ADP-83, "
CHANGEOVER SWITCH : Diagnosis Procedure".
CHANGEOVER SWITCH : Diagnosis ProcedureINFOID:0000000006248379
1.CHECK CHANGEOVER SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK CHANGEOVER SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check continuity between automatic drive posit ioner control unit harness connector and door mirror
remote control switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace harness.
Monitor item Condition
MIR CHNG SW-R/L When operating the changeover toward the right or left side. : ON
Other than the above. : OFF
(+)
(-)Voltage (V)
(Approx.)
Door mirror remote
control switch
Connector Terminal
M8 2
Ground 5
3
Automatic drive positioner control unit Door mirror remote control switch Continuity
Connector Terminal Connector Terminal
M75 2
M8 3
Existed
14 2
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M75 2
Not existed
14
Revision: 2010 May2011 QX56