INFINITI QX56 2011 Factory Service Manual

ECM
EC-87
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
91
(R) 97
(W) Throttle position sensor 1 Input [Ignition switch: ON]
 Engine: Stopped
 Selector lever: D position
 Accelerator pedal: Fully released
More than 0.36 V
[Ignition switch: ON]
 Engine: Stopped
 Selector lever: D position
 Accelerator pedal: Fully depressed Less than 4.75 V
94
(R) 175
(B) A/F sensor 1 (bank 1) Input [Ignition switch: ON] 2.0 V
95
(L/R) 68
(BR/
W) Camshaft position sensor (bank
1)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle 3.0 - 5.0 V
[Engine is running]
 Engine speed: 2,000 rpm 3.0 - 5.0 V
96
(W/ R) 100
(R) Heated oxygen sensor 2 (bank
1)
Input[Engine is running]
 Revving engine from idle to 3,000
rpm quickly after the following condi-
tions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 0 - 1.0 V
97
(W) —Sensor ground
[Throttle position sensor (bank
1)] —— —
98
(G/ W) —
Sensor ground
(Crankshaft position sensor)
—— —
99
(LG/ B) —Sensor ground
[Camshaft position sensor (bank
2)] —— —
100 (R) —Sensor ground
(Heated oxygen sensor 2) —— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JMBIA0045GB
JMBIA0046GB
Revision: 2010 May2011 QX56

EC-88
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
101
(R)
102 (R) 175
(B) Fuel injector No. 1 (HI)
Fuel injector No. 6 (HI)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
103 (G)
104 (G) 175
(B) Fuel injector No. 7 (LO)
Fuel injector No. 4 (LO)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
105
(L/W) 175
(B) High pressure fuel pump (HI) Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
JPBIA3340ZZ
JPBIA3341ZZ
Revision: 2010 May2011 QX56

ECM
EC-89
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
106
(R)
107 (R) 175
(B) Fuel injector No. 7 (HI)
Fuel injector No. 4 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
108 (G)
109 (G) 175
(B) Fuel injector No. 1 (LO)
Fuel injector No. 6 (LO)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
11 0
(L/B) 175
(B) High pressure fuel pump (LO) Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
JPBIA3342ZZ
JPBIA3343ZZ
Revision: 2010 May2011 QX56

EC-90
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
111
(R) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
11 2
(SB) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
11 4 (B) — ECM ground — — —
11 5 (B) — ECM ground — — —
120 (Y) 175
(B) EVAP canister vent control valve Output [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
122
(BR/ W) 175
(B) VVEL actuator motor relay abort
signal (VVEL control module)
Input [Ignition switch: ON] 0 V
123
(V/R) 175
(B) Throttle control mo
tor relay Output [Ignition switch: ON
→ OFF] 0 - 1.0 V
↓
BATTERY VOLTAGE
(11 - 14 V)
↓
0 V
[Ignition switch: ON] 0 - 1.0 V
125
(GR) 175
(B) Fuel pump control module
(FPCM)
Output[When cranking engine] 0 - 0.5 V
[Engine is running]
 Warm-up condition
0 - 4.0 V
126 (O) 129
(P/L) Accelerator pedal position sen-
sor 2
Input[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully released
0.28 - 0.48 V
[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully depressed 2.0 - 2.5 V
128 (Y) 130
(R) ASCD steering switch Input [Ignition switch: ON]
 ASCD steering switch: OFF
4 V
[Ignition switch: ON]
 MAIN switch: Pressed 0 V
[Ignition switch: ON]
 CANCEL switch: Pressed 1 V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed 3 V
[Ignition switch: ON]
 SET/COAST switch: Pressed 2 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3344ZZ
Revision: 2010 May2011 QX56

ECM
EC-91
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
128
(Y) 175
(B) ICC steering switch Input [Ignition switch: ON]
 ICC steering switch: OFF
4.2 V
[Ignition switch: ON]
 MAIN switch: Pressed 0 V
[Ignition switch: ON]
 CANCEL switch: Pressed 1.9 V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed 3.7 V
[Ignition switch: ON]
 SET/COAST switch: Pressed 3.2 V
[Ignition switch: ON]
 DISTANCE switch: Pressed 2.6 V
[Ignition switch: ON]
 DYNAMIC DRIVER ASSISTANCE switch: Pressed 1.0 V
129
(P/L) —Sensor ground
(Accelerator pedal position sen-
sor 2)
—— —
130 (R) —Sensor ground
(ASCD steering switch/ICC
steering switch) —— —
131
(L/W) 129
(P/L) Sensor power supply
(Accelerator pedal position sen-
sor 2)
— [Ignition switch: ON] 5 V
133
(SB) 150
(R) Sensor power supply
(Refrigerant pressure sensor/
Battery current sensor/EVAP
control system pressure sensor)
— [Ignition switch: ON] 5 V
134
(V/W) 175
(B) Fuel temperature sensor Input
[Engine is running]
 Warm-up condition2.8 V
136 (W/
R) 140
(R/Y) Accelerator pedal position sen-
sor 1
Input[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully released
0.65 - 0.87 V
[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully depressed 4.3 - 4.8 V
137 (W/
G) 140
(R/Y) Sensor power supply
(Accelerator pedal position sen-
sor 1)
— [Ignition switch: ON] 5 V
138 (V) 150
(R) Battery current sensor Input [Engine is running]
 Battery: Fully charged*
2
 Idle speed2.6 - 3.5 V
139 (G) 175
(B) Battery temperature sensor Input [Engine is running]
 Battery temperature: 25
°C
 Idle speed 3.3 V
140
(R/Y) —Sensor ground
(Accelerator pedal position sen-
sor 1) —— —
141
(SB) 175
(B) Ignition switch Input [Ignition switch: OFF] 0 V
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
Revision: 2010 May2011 QX56

EC-92
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
142
(R/W) 175
(B) Fuel pump control module
(FPCM) check
Input[When cranking engine] 0 V
[Engine is running]
 Warm-up condition
 Idle speed
9 V
143
(L/Y) 150
(R) EVAP control system pressure
sensor
Input [Ignition switch: ON] 1.8 - 4.8 V
144
(O/B) 150
(R) Refrigerant pressure sensor Input [Engine is running]
 Warm-up condition
 Both A/C switch and blower fan mo-
tor switch: ON (Compressor oper-
ates) 1.0 - 4.0 V
146 (L) — CAN communication line — — —
147
(G/Y) 175
(B) ASCD/ICC brake switch Input [Ignition switch: ON]
 Brake pedal: Slightly depressed
0 V
[Ignition switch: ON]
 Brake pedal: Fully released BATTERY VOLTAGE
(11 - 14 V)
150 (R) —Sensor ground
(Refrigerant pressure sensor/
Battery current sensor/EVAP
control system pressure sensor) —— —
151 (P) — CAN communication line — — —
156 (L) 175
(B) Power supply
for ECM (Back-
up) Input [Ignition switch: OFF] BATTERY VOLTAGE
(11 - 14 V)
158
(W/B) 175
(B) Stop lamp switch Input [Ignition switch: OFF]
 Brake pedal: Fully released
0 V
[Ignition switch: OFF]
 Brake pedal: Slightly depressed BATTERY VOLTAGE
(11 - 14 V)
161 (R/W) — ENG communication line — — —
163
(L/G) 175
(B) ECM relay (Self shut-off) Output [Engine is running]
[Ignition switch: OFF]
 A few seconds after turning ignition
switch OFF 0 - 1.5 V
[Ignition switch: OFF]
 More than a few seconds after turn- ing ignition switch OFF BATTERY VOLTAGE
(11 - 14 V)
165
(GR/ R) —
NOTE:
Not used —— —
166 (W) — ENG communication line — — —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
Revision: 2010 May2011 QX56

ECM
EC-93
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: This may vary depending on internal resistance of the tester.
*2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to PG-159, "
How to Handle Battery".
Fail-safeINFOID:0000000006217731
NON DTC RELATED ITEM
DTC RELATED ITEM
169
(G/B) 175
(B) Engine speed signal output Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle 0 - 7.0 V
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm 0 - 7.0 V
171 (W) 175
(B) Power supply for ECM Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
172 (W) 175
(B) Power supply for ECM Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
173 (O) 175
(B) Throttle contro
l motor power
supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
174 (B) — ECM ground — — —
175 (B) — ECM ground — — —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3352ZZ
JPBIA3354ZZ
Detected items Engine operating condition
in fail-safe mode RemarksReference
page
Malfunction indicator
circuit Engine speed will not rise
more than 2,500 rpm due
to the fuel cut When there is an open circuit on MIL circuit, the ECM cannot warn
the driver by illuminating MIL when there is malfunction on engine
control system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns
the driver that engine control system malfunctions and MIL circuit is
open by means of operating the fail-safe function.
The fail-safe function also operates when above diagnoses except
MIL circuit are detected and demands the driver to repair the malfunc-
tion. EC-515
Revision: 2010 May2011 QX56

EC-94
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
DTC No. Detected items Engine operating condition in fail-safe mode
U0113
U1003
U1024 Can communication circuit VVEL actuator
motor relay is turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0087 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0088 Engine speed is limited.
P008A Low fuel pressure control
system Engine torque is limited.
P0090 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit
Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT-III displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT-III display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx. 4 minutes or more after
engine starting 80
°C (176 °F)
Except as shown above 40 - 80 °C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0190 FRP sensor  Engine speed is limited.
 High pressure fuel pump is activated at maximum discharge pressure.
P0201
P0202
P0203
P0204
P0205
P0206
P0207
P0208 Injector  Engine torque is limited.
 Fuel injection shut-off of malfunction cylinder.
 Mixture ratio feedback control does not function.
 Idle engine speed is increased.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0605 ECM (When ECM calculation function is malfunctioning:)
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0607 ECM VVEL actuator motor relay is
turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
Revision: 2010 May2011 QX56

ECM
EC-95
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P062B ECM Type1
 Engine torque is limited.
 Idle engine speed is increased.
 Fuel injector power supply shut-off.
 High fuel pressure limitation.
Typ e2
 Engine torque is limited.
 Fuel injection shut-off of malfunction cylinder.
 Mixture ratio feedback control does not function.
 Idle engine speed is increased.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P1087
P1088 VVEL control function VVEL of no
rmal bank is controlled at VVEL angle of abnormal bank.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1089
P1092 VVEL control shaft position
sensor VVEL value is maintained at a fixed angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut
P1197 Out of gas  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P1608 VVEL control shaft position
sensor VVEL actuator motor relay is turned off, an
d VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1090
P1093 VVEL actuator motor VVEL of no
rmal bank is controlled at VVEL angle of abnormal bank.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
VVEL actuator motor relay is turned off, an d VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1091 VVEL actuator motor rela
y VVEL actuator motor relay is turned off, an d VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1197 Out of gas  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P2101 Electric throttle control
function ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118 Throttle control motor ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2119 Electric throttle control ac-
tuator
(When electric throttle control actuator does not function properly due to the return spring
malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the
idle position. The engine speed will not rise more than 2,000 rpm.
(When throttle valve opening angle in fail-safe mode is not in specified range:)
ECM controls the electric throttle control actuator because of regulating the throttle open-
ing to 20 degrees or less.
(When ECM detects the throttle valve is stuck open:)
While the vehicle is being driven, it slows down gradually by fuel cut. After the vehicle
stops, the engine stalls.
The engine can restart in the N or P position, and engine speed will not exceed 1,000 rpm
or more.
P1290
P2100
P2103 Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P1606 VVEL control module VVEL
actuator motor relay is turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1805 Brake switch ECM controls the electric throttle control
actuator by regulating the throttle opening to a
small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
DTC No. Detected items Engine operating condition in fail-safe mode
Revision: 2010 May2011 QX56

EC-96
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
DTC Inspection Priority Chart
INFOID:0000000006217732
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the following priority
chart.
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor
The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P2539 Low fuel pressure sensor Engine torque is limited.
DTC No. Detected items Engine operating condition in fail-safe mode
Revision: 2010 May2011 QX56