keyless INFINITI QX56 2011 Factory Workshop Manual

DIAGNOSIS SYSTEM (BCM)INL-15
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K
M A
B
INL
N
O P
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)INFOID:0000000006216060
WORK SUPPORT
*:Factory setting PUSH SW
[On/Off]
The switch status input from push-button ignition switch
UNLK SEN -DR
[On/Off] Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off] The switch status input from door switch (driver side)
DOOR SW-AS
[On/Off] The switch status input from door switch (passenger side)
DOOR SW-RR
[On/Off] The switch status input from rear door switch RH
DOOR SW- RL
[On/Off] The switch status input from rear door switch LH
DOOR SW- BK
[On/Off] The switch status input from back door switch
CDL LOCK SW
[On/Off] Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off] Unlock switch status input from door lock and unlock switch
KEY CYL LK-SW
[On/Off] Lock switch status received from door key cylinder switch
KEY CYL UN-SW
[On/Off] Unlock switch status received from door key cylinder switch
TRNK/HAT MNTR
[On/Off] NOTE:
The item is indicated, but not monitored.
RKE-LOCK
[On/Off] Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off] Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit] Description
Test item Operation Description
INT LAMP OnOutputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, personal lamp, foot lamp (when applicable lamps switch is in DOOR po-
sition.)]
Off Stops the interior room lamp control signal to turn the interior room lamps OFF.
STEP LAMP TEST On Outputs the step lamp control signal to turn the step lamps ON.
Off Stops the step lamp control signal to turn the step lamps ON.
Service item Setting item Setting
ROOM LAMP TIMER SET MODE 1
*30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2 60 min.
BATTERY SAVER SET On
*With the exterior lamp battery saver function
Off Without the exterior lamp battery saver function
Revision: 2010 May2011 QX56

INL-16
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
*: Each lamp switch is in ON position.Monitor item
[Unit] Description
REQ SW-DR
[On/Off] The switch status input from door request switch (driver side)
REQ SW-AS
[On/Off] The switch status input from door request switch (passenger side)
REQ SW-RR
[On/Off] NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off] The switch status input from push-button ignition switch
UNLK SEN-DR
[On/Off] Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off] The switch status input from door switch (driver side)
DOOR SW-AS
[On/Off] The switch status input from door switch (passenger side)
DOOR SW-RR
[On/Off] The switch status input from rear door switch RH
DOOR SW- RL
[On/Off] The switch status input from rear door switch LH
DOOR SW- BK
[On/Off] The switch status input from back door switch
CDL LOCK SW
[On/Off] Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off] Unlock switch status input from door lock and unlock switch
KEY CYL LK-SW
[On/Off] Lock switch status received from door key cylinder switch
KEY CYL UN-SW
[On/Off] Unlock switch status received from door key cylinder switch
TRNK/HAT MNTR
[On/Off] NOTE:
The item is indicated, but not monitored.
RKE-LOCK
[On/Off] Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off] Unlock signal status received from remote keyless entry receiver
Test item Operation Description
BATTERY SAVER Off Cuts the interior room lamp power supply to turn interior room lamps OFF.
On Outputs the interior room lamp power supply to turn interior room lamps ON.*
Revision: 2010 May2011 QX56

PCS
DIAGNOSIS SYSTEM (BCM)PCS-41
< SYSTEM DESCRIPTION > [POWER DISTRIBUTION SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
 On: Operate
 Off: Non-operation
TRUNK/GLASS HATCH OPEN Buzzer reminder function mode by back door opener switch can be changed to operation with
this mode
 On: Operate
 Off: Non-operation
PANIC ALARM SET Panic alarm button pressing time on Intelligent Key button can be selected from the following
with this mode
 MODE 1: 0.5 sec
 MODE 2: Non-operation
 MODE 3: 1.5 sec
TRUNK OPEN DELAY Back door open button pressing to Intelligent Key button can be selected as per the following
in this mode
 MODE 1: Press and hold
 MODE 2: Press twice
 MODE 3: Press and hold, or press twice
LO- BATT OF KEY FOB WARN Intelligent Key low battery warning mode can be changed to operation with this mode
 On: Operate
 Off: Non-operation
ANTI KEY LOCK IN FUNCTI Key reminder function mode can be changed to operation with this mode
 On: Operate
 Off: Non-operation
HAZARD ANSWER BACK Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
 Lock Only: Door lock operation only
 Unlock Only: Door unlock operation only
 Lock/Unlock: Lock and unlock operation
 Off: Non-operation
ANS BACK I-KEY LOCK Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
 Horn Chirp: Sound horn
 Buzzer: Sound Intelligent Key warning buzzer
 Off: Non-operation
ANS BACK I-KEY UNLOCK Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
 On: Operate
 Off: Non-operation
SHORT CRANKING OUTPUT Starter motor can operate during the times below
 70 msec
100 msec
200 msec
CONFIRM KEY FOB ID It can be checked wh ether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET Auto door lock operation time can be changed in this mode
 MODE 1: OFF
 MODE 2: 30 sec
 MODE 3: 1 minute
 MODE 4: 2 minutes
 MODE 5: 3 minutes
 MODE 6: 4 minutes
 MODE 7: 5 minutes
HORN WITH KEYLESS LOCK Horn reminder function mode by Intelligent Key button can be selected from the following with
this mode
 On: Operate
 Off: Non-operation
Monitor item Description
Revision: 2010 May2011 QX56

PCS
DIAGNOSIS SYSTEM (BCM)PCS-43
< SYSTEM DESCRIPTION > [POWER DISTRIBUTION SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1 When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2 NOTE:
This item is displayed, but cannot be monitored
Monitor Item Condition
Test item Description
BATTERY SAVER This test is able to check interior room lamp operation
 On: Operate
 Off: Non-operation
OUTSIDE BUZZER This test is able to check Intelligent Key warning buzzer operation
 On: Operate
 Off: Non-operation
INSIDE BUZZER This test is able to check warning chime in combination meter operation
 Take Out: Take away warning chime sounds when CONSULT-III screen is touched
 Key: Key warning chime sounds when CONSULT-III screen is touched
 Knob: OFF position warning chime sounds when CONSULT-III screen is touched
 Off: Non-operation
INDICATOR This test is able to check warning lamp operation
 KEY ON: “KEY” Warning lamp illuminates when CONSULT-III screen is touched
 KEY IND: “KEY” Warning lamp blinks when CONSULT-III screen is touched
 Off: Non-operation
INT LAMP This test is able to check interior room lamp operation
 On: Operate
 Off: Non-operation
LCD This test is able to check meter display information
 Engine start information displays when “BP N” on CONSULT-III screen is touched
 Engine start information displays when “BP I” on CONSULT-III screen is touched
 Key ID warning displays when “ID NG” on CONSULT-III screen is touched
 Steering lock information displays when “ROTAT” on CONSULT-III screen is touched
 P position warning displays when “SFT P” on CONSULT-III screen is touched
 INSRT: This item is displayed, but cannot be monitored
 BATT: This item is displayed, but cannot be monitored
 Take away through window warning displays when “NO KY” on CONSULT-III screen is
touched
 Take away warning displa y when “OUTKEY” on CONSUL T-III screen is touched
 OFF position warning display when “LK WN” on CONSULT-III screen is touched
FLASHER This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched
P RANGE This test is able to check A/T shift selector power supply
 On: Operate
 Off: Non-operation
ENGINE SW ILLUMI This test is able to check push-button ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched
Revision: 2010 May2011 QX56

PWC-3
C
DE
F
G H
I
J
L
M A
B
PWC
N
O P
WHEN BOTH POWER WINDOW MAIN SWITCH
AND REAR POWER WINDOW SWITCH LH ARE
OPERATED ...........................................................
....
64
WHEN BOTH POWER WINDOW MAIN SWITCH
AND REAR POWER WINDOW SWITCH LH ARE
OPERATED : Diagnosis Procedure ........................
64
REAR RH SIDE POWER WINDOW ALONE
DOES NOT OPERATE .......................................
65
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED ................................................................ ....
65
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED : Diagnosis Procedure .............................
65
WHEN REAR POWER WINDOW SWITCH RH IS
OPERATED ........................................................... ....
65
WHEN REAR POWER WINDOW SWITCH RH IS
OPERATED : Diagnosis Procedure ........................
65
WHEN BOTH POWER WINDOW MAIN SWITCH
AND REAR POWER WINDOW SWITCH RH ARE
OPERATED ........................................................... ....
65
WHEN BOTH POWER WINDOW MAIN SWITCH
AND REAR POWER WINDOW SWITCH RH ARE
OPERATED : Diagnosis Procedure ........................
65
AUTO OPERATION DOES NOT OPERATE
BUT MANUAL OPERATE NORMALLY ............
66
DRIVER SIDE ........................................................ ....66
DRIVER SIDE : Diagnosis Procedure .....................66
PASSENGER SIDE ...................................................66
PASSENGER SIDE : Diagnosis Procedure ........ ....66
REAR LH ............................................................... ....66
REAR LH : Diagnosis Procedure ............................66
REAR RH ............................................................... ....67
REAR RH : Diagnosis Procedure ............................67
ANTI-PINCH FUNCTION DOES NOT OPER-
ATE ....................................................................
68
Diagnosis Procedure ........................................... ....68
POWER WINDOW RETAINED POWER
FUNCTION DOES NOT OPERATE NORMAL-
LY ......................................................................
69
Diagnosis Procedure ...............................................69
DOOR KEY CYLINDER SWITCH DOES NOT
OPERATE POWER WINDOWS ........................
70
Diagnosis Procedure ...............................................70
KEYLESS POWER WINDOW DOWN DOES
NOT OPERATE .................................................
71
Diagnosis Procedure ...............................................71
POWER WINDOW LOCK SWITCH DOES
NOT FUNCTION ................................................
72
Diagnosis Procedure ...............................................72
POWER WINDOW SWITCH DOES NOT IL-
LUMINATE ........................................................
73
DRIVER SIDE ......................................................... ....73
DRIVER SIDE : Diagnosis Procedure .....................73
PASSENGER SIDE ....................................................73
PASSENGER SIDE : Diagnosis Procedure ........ ....73
REAR LH ................................................................ ....73
REAR LH : Diagnosis Procedure .............................73
REAR RH ............................................................... ....73
REAR RH : Diagnosis Procedure ............................73
REMOVAL AND INSTALLATION ...............74
POWER WINDOW MAIN SWITCH ...................74
Removal and Installation ..................................... ....74
Revision: 2010 May2011 QX56

PWC-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006217264
1. BCMRefer to BCS-4, "
BODY CONTROL
SYSTEM : Componen t Parts Loca-
tion"
2. Front power window motor (driver
side) 3. Power window main switch
4. Front door lock assembly (driver side) (door key cylinder switch) 5. Front door switch (driver side) 6. Rear power window motor LH
7. Rear power window switch LH 8. Remote keyless entry receiver Refer to DLK-11, "
DOOR LOCK
SYSTEM :
ComponentPartsLocation"
A. View with front door finisher removed B. View with rear door finisher removed
JMKIA5275ZZ
Revision: 2010 May2011 QX56

COMPONENT PARTSPWC-7
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
L
M A
B
PWC
N
O P
Component DescriptionINFOID:0000000006217265
Component Function
BCM  Supplies power supply to power window switch.
 Controls retained power.
Power window main switch  Directly controls all power window motor of all doors.
 Controls anti-pinch operation of power window.
Front power window switch
(passenger side)  Controls anti-pinch operation of power window.
 Controls power window motor of passenger door.
Rear power window switch  Controls anti-pinch operation of power window.
 Controls power window motor of rear right and left doors.
Power window motor  Integrates the ENCODER and WINDOW MOTOR.
 Starts operating with signals from each power window switch.
 Transmits power window motor rotation as a pulse signal to power window switch.
Remote keyless entry receiver Receives lock/unlock signal from the intelligent key, and then transmits to BCM.
Front door lock assembly (door key cyl-
inder switch) Transmits operation condition of door key cylinder switch to power window main switch.
Front door switch (driver side/passen-
ger side) Front door open/close condition and transmits to BCM.
Revision: 2010 May2011 QX56

SYSTEMPWC-9
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
L
M A
B
PWC
N
O P
The signal mentioned below is transmitted from BCM to power window main \
switch, front power window
switch (passenger side) and rear power window switch LH/RH.
 Keyless power window down signal
 Door switch signal
The signal mentioned below is transmitted from power window main switch to front power window switch (pas-
senger side) and rear power window switch LH/RH.
 Front passenger side door window and rear door window operation signal
 Power window control by door key cylinder switch signal
 Power window lock switch signal
 Retained power operation signal
RETAINED POWER OPERATION
 Retained power operation is an additional power supply function that enables power window system to oper-
ate during the 45 seconds even when ignition switch is turned OFF.
Retained Power Function Cancel Conditions
 Front door CLOSE (door switch OFF) →OPEN (door switch ON).
 When ignition switch is ON again.
 When timer time passes. (45 seconds)
POWER WINDOW LOCK FUNCTION
Ground circuit inside power window main switch shuts off when power window lock switch is ON. This inhibits
power window switch operation except with the power window main switch.
ANTI-PINCH OPERATION
 Anti-pinch foreign lowers door glass 150 mm (5.9 in) when foreign material is pinched in door glass during
AUTO-UP operation.
 Encoder continues detecting the movement of power window motor and output the encoder pulse signal to
power window switch l while power window motor is operating.
 Resistance is applied to the power window motor ro tation that changes the frequency of encoder pulse sig-
nal if foreign material is trapped in the door glass.
 Power window switch controls to lower the door glass for 150 mm (5.9 in) after it detects encoder pulse sig-
nal frequency change.
Operation Condition
When all door glass AUTO-UP operation is performed ( anti-pinch function does not operate just before the
door glass closes and is fully closed)
NOTE:
Depending on environment and driving conditions, if a similar impact or load is applied to the door glass, it
may lower.
DOOR KEY CYLINDER SWITCH OPERATION
Hold the door key cylinder to the LOCK or UNLOCK direct ion for 1.5 seconds or more to OPEN or CLOSE all
power windows when ignition switch is OFF. In addition, it stops when key position is moved to NEUTRAL
when operating.
Operation Condition
 Ignition switch OFF.
 Hold door key cylinder to LOCK position for 1.5 se conds or more to perform CLOSE operation of the door
glass.
 Hold door key cylinder to UNLOCK position for 1.5 se conds or more to perform OPEN operation of the door
glass.
KEYLESS POWER WINDOW DOWN FUNCTION
All power windows open when the unlock button on Intelligent Key is activated and kept pressed for more than
3 seconds with the ignition switch OFF. The wi ndows keep opening if the unlock button is continuously
pressed.
The power window opening stops when the following operations are performed.
 When the unlock button is kept pressed more than 15 seconds.
 When the ignition switch is turned ON while the power window opening is operated.
 When the unlock button is released.
While retained power operation activate, keyless power window down function cannot be operated.
Revision: 2010 May2011 QX56

PWC-10
< SYSTEM DESCRIPTION >
SYSTEM
Keyless power window down operation function can be changed by “PW DOWN SET” in “WORK SUPPORT”
mode of “INTELLIGENT KEY” of “B CM” using CONSULT-III. Refer to DLK-41, "
INTELLIGENT KEY : CON-
SULT-III Function (BCM - INTELLIGENT KEY)".
NOTE:
Use CONSULT-III to change settings.
MODE 1 (3 sec) / MODE 2 (OFF) / MODE 3 (5 sec)
Fail-safeINFOID:0000000006217268
FAIL-SAFE CONTROL
Switches to fail-safe control when malfunction is detected in encoder signal that detects up/down speed and
direction of door glass. Switches to fail-safe control when a signal that is out of the specified value is detected
between the fully closed position and the actual position of the glass.
If fail-safe control, the system changes to a non-init ialized condition and the following function do not operate.
 Auto-up operation
 Anti-pinch function
 Retained power function
When fail-safe control is activated, perform initialization procedure to reco ver. If a malfunction is detected in
power window switch or more, fail -safe control is activated again.
Malfunction Malfunction condition
Pulse sensor malfunction When one pulse signal that is the specified value or more is detected continuously for the specified
time or more, while door glass is being operated UP or DOWN.
Both pulse sensors mal-
function When both pulse signals are not detected continuously for the specified time or more, while door
glass is being operated UP or DOWN.
Pulse direction malfunc-
tion When a pulse signal indicating that window is moving in the opposite direction against the power win-
dow motor is detected for the specified value or more, while door glass is being operated UP or
DOWN.
Glass recognition position
malfunction 1 When the actual door glass position that is out of specified value is detected compared to the door
glass fully closed position memorized in module, while door glass is being operated UP or DOWN.
Glass recognition position
malfunction 2 When pulse count that is out of the door glass full stroke value or more is detected, while door glass
is being operated UP or DOWN.
Revision: 2010 May2011 QX56

KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
PWC-71
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000006217338
1.CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent key button?
YES >> GO TO 2.
NO >> Refer to DLK-175, "
Diagnosis Procedure".
2.CHECK POWER WINDOW OPERATION
Check power window operation.
Does power window up/down with power window main switch?
YES >> GO TO 3.
NO >> Refer to PWC-35, "
POWER WINDOW MAIN SWITCH : Diagnosis Procedure".
3.CHECK “PW DOWN SET” SETTING IN “WORK SUPPORT”
Check “PW DOWN SET” setting in “WORK SUPPORT”.
Refer to DLK-41, "
INTELLIGENT KEY : CONSULT-III F unction (BCM - INTELLIGENT KEY)".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Set “PW DOWN SET” setting in “WORK SUPPORT”.
4.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> GO TO 1.
Revision: 2010 May2011 QX56