JAGUAR XFR 2010 1.G Owner's Guide
XFR 2010 1.G
JAGUAR
JAGUAR
https://www.carmanualsonline.info/img/21/7642/w960_7642-0.png
JAGUAR XFR 2010 1.G Owner's Guide
Page 413 of 3039
7. NOTE: Left-hand shown, right-hand similar.
Release the brake caliper.
Remove and discard the 2 bolts.
Tie the brake caliper aside.
8. NOTE: Left-hand shown, right-hand similar.
Disconnect the rear wheel speed sensor.
9. Disconnect the electronic parking brake actuator electrical
connector.
10. NOTE: Left-hand shown, right-hand similar.
Disconnect both parking brake cables from the rear brake
calipers.
Page 414 of 3039
11.
12.
13.
14. NOTE: Left-hand shown, right-hand similar.
Detach the shock absorber.
Detach the fuel filler hose.
CAUTION: Under no circumstances must the flexible
coupling (or its fixings) be loosened or removed from the
driveshaft.
Detach the driveshaft from the rear drive axle flange.
Mark the position of the driveshaft in relation to the
rear drive axle flange.
Mark the position of the balance nut in relation to the
rear drive axle flange. (if fitted).
Mark the position of each nut and bolt in relation to the
driveshaft flexible joint.
NOTE: Left-hand shown, right-hand similar.
Remove the rear subframe reinforcement plate retaining bolts. www.JagDocs.com
Page 415 of 3039
15.
16.
17.
18. Install the special tool to support the rear subframe.
NOTE: Left-hand shown, right-hand similar.
Remove the rear subframe rear retaining bolt.
NOTE: Left-hand shown, right-hand similar.
Remove the rear subframe front retaining bolt.
Remove the rear subframe.
Page 417 of 3039
2. Install new nuts to the stabilizer bar links.
Tighten to 48 Nm.
3. Install the rear subframe.
4. NOTE: Left-hand shown, right-hand similar.
Loosely install the rear subframe front bolt.
5. Loosely install the rear subframe rear bolt.
Page 418 of 3039
6. NOTE: Left-hand shown, right-hand similar.
Loosely install the rear subframe reinforcement plate bolts.
7. Tighten the subframe bolts.
Tighten to 80 Nm + 240°.
8. Remove the special tool.
9. Tighten the rear subframe reinforcement plate retaining bolts.
Tighten to 47 Nm.
Page 505 of 3039
Vehicles with diesel engine
7.
8.
All vehicles
9.
Remove the support bracket.
Remove the bolts.
Detach the intermediate muffler exhaust hanger
insulators.
Loosen the catalytic converter to diesel particulate filter
(DPF) retaining clamps.
CAUTION: Make sure that the exhaust system is
supported with a suitable transmission stand.
Lower the exhaust assembly sufficiently to gain access to
the driveshaft heat shield.
Release the 6 exhaust hangers.
Page 511 of 3039
Centre bearing retaining bolts 48 36 - Transmission flexible joint retaining bolts 127 94 - Rear drive axle CV joint retaining bolts 73 54 - Driveshaft heat shield retaining bolts 7 - 62
Page 524 of 3039
Installation
1. CAUTION: Only tighten the bolts finger-tight at this
stage.
2. NOTE: Make sure that the alignment mark on the
driveshaft is correctly aligned to the alignment mark on the
differential case.
Torque: 75 Nm
Page 528 of 3039
Differential fluid - vehicles without supercharger Castrol SAF XO (75W 90) Differential fluid - vehicles with supercharger Castrol BOT 720 (75W 90) Initial Specifications
Item Specification Differential fluid capacity - vehicles without supercharger 0.9 Liters Differential fluid capacity - vehicles with supercharger 1.3 Liters Service Specifications
Item Specification Differential fluid capacity - vehicles without supercharger 0.85 Liters Differential fluid capacity - vehicles with supercharger 1.25 Liters Torque Specifications
Description Nm lb-ft lb-in Differential case front retaining bolt 90 66 - Differential case rear retaining bolts 192 142 - Differential filler plug 27 20 - Differential drain plug 27 20 - Halfshaft constant velocity joint nut 300 221 - Driveshaft retaining bolts 73 54 - www.JagDocs.com
Page 535 of 3039
Thrust race 7 Shim 8 Thrust plate 9 Dished washer 10 Bolt (10 off) 11 Clutch basket 12 Multi-plate clutch and pressure disc 13 Differential case 14 Screw (2 off) 15 Bearing assembly 16 Oil seal 17 Oil slinger inner 18 Oil slinger outer 19 Input flange 20 Pinion nut 21 Collapsible spacer 22 Shim 23 Bearing assembly 24 Pinion shaft 25 Mounting insulator inner (2 off) 26 Mounting insulator rubber (2 off) 27 Mounting insulator outer (2 off) 28 Carrier 29 Oil seal 30 Drain plug 31 Vent 32 Breather cap 33 Shim 34 Bearing assembly 35 Drive gear 36 Shim 37 RH sun gear 38 Circlip 39 Thrust washer (4 off) 40 Planet gear (4 off) 41 Pin (2 off) 42 Shaft 43 LH sun gear 44 Shim 45 Bearing assembly 46 Shim 47 Dowel (2 off) 48 Bolt (4 off) 49 Reduction gear casing 50 Reduction gear 51 Shaft 52 Temperature sensor 53 O-ring seal 54 Motor 55 Screw (4 off) 56 Cover 57 Output actuator locking pin 58 Bolt (9 off)
