sensor MAZDA 626 1987 Owners Manual

4D FUEL SYSTEM
76G04D-047
76G04D-048
76G04D-049
FUEL FILTER
On-Vehicle Inspection
Check for water in the fuel filter. If present drain the
water. (Refer to page 4D—4.)
Replacement
Removal
1. Disconnect the water level sensor connector (ECE).
2. Remove the water level sensor. (ECE).
3. Remove the fuel filter cartridge.
Warning
Keep fire and open flame away from the fuel
area.
Installation
1. Apply fuel to the O-ring of the fuel filter cartridge
and install it onto the filter body.
2. Install the water level sensor (ECE).
3. Connect the water level sensor connector (ECE).
4. Bleed air from fuel filter. (Refer to page 4D—4.)
5. Check for fuel leakage.
SEDIMENTER (GENERAL)
On-Vehicle Inspection
Check for water in the sedimenter. If present, drain
the water. (Refer to page 4D—4.)
4D—22

FUEL SYSTEM 4D
Replacement
1. Remove the sedimenter from the body.
2. Apply fuel to a new O-ring, and install it onto the
sedimenter body with water level sensor.
76G04D-051
WATER LEVEL SENSOR
Inspection
1. Remove the water level sensor.
(ECE)
Remove the water level sensor from the fuel filter.
(GENERAL)
Remove the water level sensor from the sedimenter
body.
76G04D-052
2. Check the water level sensor for continuity with an
ohmmeter. Replace if necessary.
ECE
Continuity : Pulled condition
No continuity: Pushed condition
76G04D-053
GENERAL
Continuity : Pushed condition
No continuity: Pulled condition
3. Apply fuel to a new O-ring and install it onto the
sensor.
4. Install the water level sensor to the fuel filter (ECE)
or the sedimenter (General).
5. Check for fuel leakage.
76G04D-054
4D-23

7B
AUTOMATIC TRANSAXLE
(Electronically Controlled and 4-Speed)
OUTLINE 7B— 2
SPECIFICATIONS 7B— 2
COMPONENT LOCATION 7B— 3
STRUCTURAL VIEW 7B— 5
OPERATION OF COMPONENTS 7B— 6
FLUID PASSAGE LOCATION 7B— 9
TROUBLESHOOTING (G4A-EL) 7B— 12
GENERAL NOTE 7B— 12
STEP 1
(WARNING CODE RETRIEVAL) 7B— 15
STEP 2
(PRELIMINARY INSPECTION) 7B— 22
STEP 3 (SIGNAL INSPECTION) 7B— 24
STEP 4 (STALL TEST) 7B— 27
STEP 5 (TIME LAG TEST) 7B— 30
STEP 6 (OIL PRESSURE TEST) 7B— 31
STEP 7 (ROAD TEST) 7B— 34
TROUBLESHOOTING (G4A-HL) 7B— 41
GENERAL NOTE 7B— 41
STEP 1
(PRELIMINARY INSPECTION) 7B— 44
STEP 2 (ELECTRICAL
SYSTEM INSPECTION) 7B— 47
STEP 3 (STALL TEST) 7B— 49
STEP 4 (TIME LAG TEST) 7B- 52
STEP 5 (ROAD TEST) 7B— 53
STEP 6 (OIL PRESSURE TEST) 7B— 58
ELECTRICAL SYSTEM
COMPONENTS 7B— 63
MODE SWITCH (G4A-EL) 7B— 63
HOLD SWITCH (G4A-EL) 7B— 63
OD OFF SWITCH (G4A-HL) 7B— 64
INHIBITOR SWITCH 7B- 65
WATER TEMPERATURE SWITCH 7B— 66
FLUID TEMPERATURE SWITCH
(G4A-EL) 7B— 66
BRAKE LIGHT SWITCH
(G4A-EL) 7B— 66
KICK-DOWN SWITCH (G4A-HL) 7B— 67
PULSE GENERATOR (G4A-EL) 7B- 68
VEHICLE SPEED SENSOR
(G4A-EL) 7B— 68
CRUISE CONTROL SWITCH
(CRUISE CONTROL UNIT) 7B— 68
IDLE SWITCH AND THROTTLE
SENSOR (G4A-EL) 7B— 68
OD RELEASE SOLENOID
VALVE (G4A-HL) 7B— 68
SOLENOID VALVES (G4A-EL) 7B— 69
NO LOAD SIGNAL (G4A-EL) 7B— 69
MODE, AND HOLD INDICATOR
LIGHT (G4A-EL) 7B— 69
OD OFF INDICATOR LIGHT
(G4A-HL) 7B— 69
EC-AT CONTROL UNIT
(G4A-EL) 7B— 69
ON-VEHICLE MAINTENANCE 7B— 71
AUTOMATIC TRANSAXLE
FLUID (ATF) 7B— 71
SELECTOR LEVER 7B— 72
THROTTLE CABLE 7B— 73
CONTROL VALVE BODY 7B— 77
OIL STRAINER 7B— 79
ADJUSTMENT OF 2-4 BRAKE
BAND 78— 80
REPLACEMENT OF
DRIVESHAFT OIL SEAL 7B— 80
OIL COOLER 7B— 81
GOVERNOR (G4A-HL) 7B— 82
REMOVAL 7B— 83
PRECAUTION 7B— 83
DISASSEMBLY 7B— 88
DISASSEMBLY-STEP 1 7B— 88
DISASSEMBLY-STEP 2 7B— 94
DISASSEMBLY-STEP 3 7B— 99
DISASSEMBLY-STEP 4 7B—103
INSPECTION AND REPAIR 7B—107
PRECAUTION 7B—107
TORQUE CONVERTER 7B—107
OIL PUMP 7B—108
CLUTCH ASSEMBLY 7B—113
SMALL SUN GEAR AND
ONE-WAY CLUTCH 7B—122
ONE-WAY CLUTCH AND
CARRIER HUB ASSEMBLY 7B-126
3-4 CLUTCH 7B—128
2-3 ACCUMULATOR 7B—132
GOVERNOR ASSEMBLY
(G4A-HL) 7B-133
LOW AND REVERSE BRAKE 7B—134
2-4 BRAKE BAND 7B—135
BAND SERVO 7B—135
OTHER INSPECTION 7B—135
CONTROL VALVE BODY
(G4A-EL) 7B-136
CONTROL VALVE BODY
(G4A-HL) 7B-155
DIFFERENTIAL 7B—177
OUTPUT GEAR 7B—181
IDLE GEAR 7B—182
BEARING COVER ASSEMBLY 7B—185
BEARING HOUSING 7B—186
ASSEMBLY 7B-187
PRECATION 7B—187
ASSEMBLY-STEP 1 7B—187
ASSEMBLY-STEP 2 7B—197
ASSEMBLY-STEP 3 7B—202
ASSEMBLY-STEP 4 7B—208
INSTALLATION 7B—215
TORQUE SPECIFICATIONS 7B—215
HYDRAULIC CIRCUIT (G4A-EL) 7B—221
HYDRAULIC CIRCUIT (G4A-HL) 7B—239
76G07B-001

OUTLINE 7B
COMPONENT LOCATION
G4A-EL
76G07B-003
1. Hold indicator light
2. EC-AT control unit
3. Vehicle speed sensor
4. Mode indicator light
5. Cruise control unit
6. Cruise control switch
7. Mode switch
8. Hold switch
9. Water temperature switch
10. Throttle sensor and idle
switch
11. Fluid temperature switch
12. EC-AT
13. Pulse genelator
14. Solenoid valves
15. Inhibitor switch
7B-3

7B TROUBLESHOOTING (G4A-EL)

ON VEHICLE-
-f-
—OFF VEHICLE

\ Inspection point
and

\ reference page

Condition
•

Electronic control system Prelim-
inary
Hydraulic
control
system
Power train \ Inspection point
and

\ reference page

Condition
•
7B-66

m CO I m r--
7B-63

i
cn to I m
Section

4B

|

Section

4B

|

ID to i m
CO CO 1 CD
7B-68
|
en CO 1 IX)
to 1 00 r-.
cn CD 1 CO
7B-69
|

1 CD r--
i no
cn s-1 m
Section
4B

r*-cn
S-1 CD h-
"=1-
rJ CO
7 CD r-
(XI o
1 m
cn CM 1 CD
7B-107

|
CD
7 CD 7 m
I
7B-113
I
CO CM
7 CO r-.
m cn
7 CO r-.
cn
7 DO r-
CM CM
7 CO

|
7B-126

7 00 r-
CO 7 cn
1*-r*-
7 m r-
\ Inspection point
and

\ reference page

Condition
•
Brake

light
switch

|

Inhibitor

switch

|

Mode

switch

|

1
CO. •o o X
Idle

switch

Throttle

sensor

|

Water

temp,

switch

|
0 tn c 0) cn
s
ffi
Q tn 01 o Hi >
Pulse

generator

|

"a o c 0) a to CM
TJ O CL ID s CO C\l 3-4

solenoid

|

Lock-up
solenoid

I

ATF

level
and
condition

|

Selector

lever

m Xj CO CJ 03
1 sz
Idle
speed
and
Ignition
timing

Control

valves

Accumulators
Oil
pump
Hydraulic

circuit

Torque

converter

Forward

clutch
Coasting
clutch

Reverse

clutch
JT O
u TT ro 2-4

brake
band
and

servo
$ 2
B cn cii > £ "O C CO
o
XI y
o >. CO S cb a O
One-way

clutch

2

s CI Cn tz JC 5 0-
Planetary

gear

Differential

assembly
Accelerating

Vehicle does
not
move
in
D,
S,
L,
or R
range
O O O O O O O O O O 0

Accelerating

Vehicle moves
in N
range -0 0 -—

Accelerating
Excessive creep
-0 O O -—

Accelerating
No creep
at all
O o o o
o
G 0 O O

Shifting

|

No shift
O O o
o
0 O 0 0
o
o O

Shifting

|
Abnormal shift sequence
0 o O O 0
o
o 0 O o o 0 O

Shifting

|
Frequent shifting 0 o 0 0 o 0 O O 0

Shifting

|

Excessively high
or
low
shift point 0 o 0 O 0 0 o 0 O 0 0
Shifting

|

No lock-up
0 o 0 0 o 0 O O o O

Shifting

|

No kick-down o o o o

Slipping

Engine
run
away
or
slip when
starting vehicle 0 o 0 O o O

Slipping
Engine
run
away
or
slip when
up-
or
down-shifting o o o 0 o O 0 0 O
8 n cn 4S SI V)
Excessive
N to D or N to R

shift shock o O o o o O
8 n cn 4S SI V)
Excessive shift shock when
up-

shifting
or
downshifting o o o o 0 0 0 8 n cn 4S SI V) Excessive shift shock when
changing range 0 0 o 0 o

j
Noise

Transaxle noisy
in N or P

range o o 0 O

j
Noise

Transaxle noisy
in D, S, L,
or

R range o 0 0 O

I
Others

j

No engine braking o O o 0 o o

I
Others

j

No mode change o 0 o o o o o o o
O
o
0

I
Others

j
Transaxle overheats
o o
0 o 0 o 0

I
Others

j
Vehicle moves
in
"P",
or
park-ing gear
not

disengaged when
"P"
is
dis-
engaged
0 O

I
Others

j

Hold indicator flashes o
0
o
0
o
O
o — — —
I
Others

j

Engine will
not
start
o
o
O — — —
76G07B-014
7B—14

TROUBLESHOOTING (G4A-EL) 7B
STEP 1 (WARNING CODE RETRIEVAL)
Self-diagnosis Function
The self-diagnosis system, which is integrated in the EC-AT control unit, diagnoses malfunction of the
main sensors (input) and solenoid valves (output), and the EC-AT control unit.
Malfunctions which have happened or are continuing are memorized in the EC-AT control unit as specific
codes.
The EC-AT Tester is used to retrieve these warning codes. Each malfunction is indicated by a code
number and buzzer as shown the table below.
Code Number
Code number Location of malfunction Buzzer
06 Vehicle speed sensor or circuit JliUli c
12 Throttle sensor or circuit rui r
55 Pulse genelator or circuit nnnnruiii r
60 1-2 shift solenoid valve or circuit jinnnnn r
61 2-3 shift solenoid valve or circuit nnnnnruL_[
62 3-4 shift solenoid valve or circuit nnnnnn nn r
63 Lock-up solenoid valve or circuit
_ 1 0,4 sec
rnnnnn ihi J r1.2sec J | _1.fi sec
76G07B-213
EC-AT Tester
Assembly of EC-AT tester
1. Set the plate (49 G019 912) onto the EC-AT tester
body (49 G019 901 A).
2. Connect the adapter harness (49 G019 911) to
the EC-AT tester body.
3. Select the code select switch to A position.
4. Select the select switch to NEW 626 position.
76G07B-603
7B—15

TROUBLESHOOTING (G4A-EL) 7B
06 4 second period
55 4 second period
63
-*•
4 second period
Repeats above
General Note
1. If there is more than one malfunction, the code
numbers will be displayed on the tester one by one
in a numerical order. In the case of malfunctions,
55, 06, and 63, the code numbers are displayed
in an order of 06, 55, then 63. The display is as
shown.
86U07B-018
When the service connector
is not grounded
Malfunctions YES
NO
Hold indicator YES
flashing NQ
YES
NO
Memory in control unit
2. The hold indicator flashes to indicate the same pat-
tern as the buzzer of the EC-AT Tester when the
EC-AT service connector is grounded.
When the EC-AT service connector is not ground-
ed, the indicator flashes in a constant frequency
while a malfunction is occurring and goes out
if
the
malfunction recovers. However, the warning code
is memorized in the EC-AT control unit.
76G07B-015
Sensors-
Solenoid-valve
Fail-safe program Proces--\Out sing -v puts
The EC-AT control unit has a built-in fail-safe func-
tion for the throttle sensor, the pulse generator, and
the 1-2, 2-3, and 3-4 shift solenoid valves.
If a malfunction occurs, the EC-AT control unit will
control operation of the remaining components ac-
cording to a preset fail-safe program.
The vehicle may still be driven, although the driv-
ing performance will be slightly affected.
79G07C-062
4. The memory of warning codes is canceled by dis-
connecting the negative battery terminal for ap-
prox. five seconds.
79G07C-063
7B-17

TROUBLESHOOTING (G4A-EL) 7B
79G07C-068

Drive at 50
km/h
(31
mph)
Kick-down
Stop
the
vehicle
79G07C-069
After-repair Procedure
1. Cancel the memory of malfunctions by disconnect-
ing the negative battery terminal for at least five sec-
onds, then reconnect it.
2. Remove the EC-AT tester if it is connected.
3. Drive the vehicle at 50 km/h (31 mph), then de-
press the accelerator pedal fully to activate kick-
down. Stop the vehicle gradually.
KICK goimsv
BRAKE LIGHTS*
CRUISE CONTROL
C V,. DEPRESS FULL*
Ox
azsa
ORUti rpn
"J
i"
•
rm uu

£ZL ofF

4. Reconnect the EC-AT tester to the 6-pin service
connector.
5. Ground the 1 -pin service connector with a jumper
wire.
6. Turn the ignition switch ON.
7. Check that no code numbers are displayed.
79G07C-070
Inspection Procedure
No. 06 code display (Vehicle speed sensor)
76G07B-017
7B-19

7B TROUBLESHOOTING (G4A-EL)
No. 12 code display (Throttle sensor)
76G07B-018
No. 55 code display (Pulse generator)
Is there poor connection at connector? YES Repair or replace.
NO
Does EC-AT Tester display drum speed? (Refer to STEP 3-Signal Inspection)
YES Pulse generator OK.
Cancel memory of code number.
NO
NO Is there 200—400 12 between terminals of pulse generator connector? (Refer to page 7B—68)
NO Replace pulse generator. Is there 200—400 12 between terminals of pulse generator connector? (Refer to page 7B—68)
YES YES Check for open or short-circuit in wiring. Check for open or short-circuit in wiring.
76G07B-019
No. 60, 61, 62, or 64 code display (1-2 shift, 2-3 shift, or 3-4 shift solenoid valve)
7B-20

7B TROUBLESHOOTING (G4A-EL)
STEP 3 (SIGNAL INSPECTION)
In this step, the input and output signals are checked
with the EC-AT Tester.
The Tester checks for proper operation of the vari-
ous switches and sensors in the EC-AT system. It also
checks the control unit for output of the various con-
trol signals. Powertrain slippage is also checked.
Inspection Procedure
1. Disconnect the connectors from the EC-AT con-
trol unit.
2. Connect the adaptor harness between the control
unit and the connectors.
3. Turn the ignition switch and main switch ON.
4. Check indication of the respective light or digital
display in each condition, referring to the indica-
tion table below.
Indication table of light and digital display
Item Indication Condition Possible cause
Input (Light)
L ON L range L OFF Other ranges
S
ON S range
INHIBITOR
S OFF Other ranges Inhibitor switch or wiring SW
D ON D range
Inhibitor switch or wiring
D
OFF Other ranges
P,N
ON P or N range P,N OFF Other ranges
HOLD SW ON Hold switch pushed Hold switch or wiring HOLD SW
OFF Hold switch released
Hold switch or wiring
MODE SW ON Power mode Mode switch or wiring MODE SW
OFF Economy mode
Mode switch or wiring
IDLE SW ON Throttle valve fully closed Idle switch or wiring IDLE SW
OFF Throttle valve open
Idle switch or wiring
7B-24