MITSUBISHI 3000GT 1991 User Guide

GENERAL - How to Use This Manual00-7EXPLANATION OF CIRCUIT DIAGRAMS
/
tThe symbols used in circuit diagrams are used as
NOTEdescribed below.
For detailed information concerning the reading of
circuit diagrams, refer to Volume 2
- Circuit Dia-
grams.
indicates a connector.A : femaleT : male
The broken (----I line indi-cates the same connec-tor.
The connector symbolindicates the deviceside connector (for anintermediate connector,the male side connec-tor) as seen from theterminal front (the con-nector’sconnectionface).
mclea\4305B -.
1
i1
1L
L01
The input/output (direction of cur-rent flow) relative to the electro-nic control unit is indicated bysymbols (A. 0).The (A) symbol indicates thatcurrent flows in the upwarddirection.output
Input\Input/output
MOTOR
1
SWITCH
I
TSB Revision

00-8
GENERAL - Vehicle Identification
VEHICLE IDENTIFICATIONMOOCA- _VEHICLE IDENTIFICATION NUMBER LOCATION
The vehicle identification number
(V.I.N.) is located on a plate1Jattached to the left top
s3e of the instrument panel.
VEHICLE IDENTIFICATION CODE CHART PLATE
MOOCB- .All vehicle identification numbers contain 17 digits. The vehicle
number is a code which tells country, make, vehicle type, etc.
J-JapanA-3-X-D-s-Mitsubishi4-B-PassengerDriver13000GTM-PremiumY-
Car3-door3.0 liters000001
Air Bag,FWD6F’a;;;;ger E-Hatchback (181.4 win.)z1991
SpecialL:oHC-MP’lYearl%ya99iJF389
3000GT 7-Seat BeltAWDUltimate3.0 liters 1(181.4 cu.in.1[DOHC-MPI-Turbo]
NOTEl “Check digit” means a srigle number or letter X used to verify the accuracy of transcription of vehicle identification number,
TSB Revision

cGENERAL
- Vehicle Identificationdo-9VEHICLE IDENTIFICATION NUMBER LIST
MOOCC- .
VEHICLES FOR FEDERAL
1 V.I.N. (except sequence number)1 Brand/ Engine displacement1 Models code
JA3XD54BOMY
Mitsubishi 3000GT
JA3XD64BOMY
I
3.0 liters (181.4 cu.in.)[DOHC-MPI]
JA3XE74COMY
Mitsubishi 3000GT3.0 liters (181.4 cu.in.)Z15AMNGFL2M[DOHC-MPI-Turbo]ZlGAMNGFL2M
VEHICLES FOR CALIFORNIA
( V.I.N. (except sequence number)1 Brand
JA3XD54BClMYMitsubishi 3000GT
1 JA3XD64BlJMYI
Engine displacementModels codeI
tJA3XE74CClMY”Mitsubishi 3000GT
NOTEAWD marked with * can also be sold in Federal States. *
1
3.0 liters (181.4 cu.in.1Zl lAMNXML7M[DOHC-MPI]Zl lAMRXML7MZl lAMNPML7MZl lAMRPML7M
3.0 liters (181.4 cu.in.1Z15AMNGFL7M[DOHC-MPI-Turbo]ZIGAMNGFUMI
TSB Revision

00-10GENERAL - Vehicle Identification
0060046
.:@I*
@+!jg.., ,”
0
<1
~~~ k
,.‘.r, SS?b‘,,.‘$ .’‘S,‘,,:’
t
I
nf/OOFDO&VEHICLE INFORMATION CODE PLATE
MOOCD- .IVehicle information code plate is riveted onto the bulkhead in
the engine compartment.
:
i3' 'The place shows model code, engine model, transaxle model,
and body color code.
1. MODEL
ZllAMNXMLZM
L2iie ‘zze[2. ENGINE
6672/Engine model
3. EXTCA6
Y Exterior code
4. TRANSAXLE
F5M33
-Transaxle model
5. COLOR, INT
R2587VQ3V
OPT-p=~izgTj+Ly~deCHASSIS NUMBER
MOOCE- -
STAMPING. LOCATIONThe chassis number is stamped on the top center of thefirewall located in the engine compartment.
CHASSIS NUMBER CODE CHART
ZlOA MY[7000~10
Y cd:at!s t:beOGT-series. Refer to 10th thru 17th digits
VEHICLE SAFETY CERTIFICATION LABEL
MOOCF- -
1.The vehicle safety certification label is attached to the face
of left door pillar.
2. This label indicates the month and year of manufacture,
Gross Vehicle Weight Rating
(G.V.W.R.), Gross Axle Weight
Rating
(G.A.W.R.) front and rear, and Vehicle Identification
Number
(V.I.N.).
TSB Revision

GENERAL - Vehicle Identification00-I 1
c
Theft protection label
For original parts
OOK619
For replacement parts
[i]
001621ENGINE MODEL STAMPING
MOOCG- .
I, The engine model number is stamped at the front side on
the top edge of the cylinder block as shown in the
following:
Engine modelEngine displacement
6672
3.0 liters (181.4 cu.in.12. The engine serial number is stamped near the engine
model number, and the serial number cycles, as shown
below
Engine serial number
AA0201 to YY9999Number cyclingAA0201--- - -+ AA9999
L ABOOOI-- - - ---f AY9999
L BAOOOI - - - - + YY9999
THEFT PROTECTION.MOOCIACIn order to protect against theft, a Vehicle Identification
Number
(VIN) is stamped in, or attached as a label to, the
following major parts of the engine and transaxle, as well as
main outer panels:
Engine cylinder block, Transaxle housing, Fender, Door, Quar-
ter panel, Hood, Liftgate, Bumpers
In addition, a theft-protection label is attached
to‘ replacement
parts for the body outer panel main components, and the same
data are stamped into replacement parts for the engine and the
transaxle.
Cautions regarding panel repairs
1. When repainting original parts, do so after first mask-
ing the theft-protection label, and, after painting, be
sure to peel off the masking tape.
2. The theft-protection label for replacement parts is
covered by masking tape, so such parts can be paintedas is. The masking tape should be removed after
painting is finished.
3.The theft-protection label should not be removed fromoriginal parts or replacement parts.
c
1 TSB Revision

00-12
GENERAL - Vehicle IdentificationLOCATIO’NS

Automatic transaxle
31FOO70
The illustration indicates left hand side, outer.
Right hand side is symmetrically opposite.
TSS Revision

GENERAL - Vehicle Identification
The illustration
indicates
right hand side,
outer.Left hand side is symmetrically opposite.31FOO7131FOO72
The illustration indicates left hand side, outer.
Right hand side is symmetrically opposite.
31FOO73
TSB Revision

00-14
GENERAL - Vehicle Identification
Part
Liftgate
Front
bummer
3ear bumper
Target area: for original equipment partsvmd : for replacement parts
31FOO74OOFO013
OOFO047
TSB Revision

GENERAL - Precautions before Service0045
c
mm (in.)so005
PRECAUTIONS BEFORE SERWCEMOOOAAOSERVICING ELECTRICAL SYSTEM
1. Note the following before proceeding with work on the
electrical system.
Note that the following must never be done:
Unauthorized modifications of any electrical device or
wiring, because such modifications might lead to a vehicle
malfunction, over-capacity or short-circuit that could result
in a fire in the vehicle.
2. When servicing the electrical system, disconnect the
negative cable terminal from the battery.
Caution1. Before connecting or disconnecting the negative
cable, be sure to turn off the ignition switch and the
lighting switch.(If this is not done, there is the possibility of
semiconductor parts being damaged.)
2. After completion of the work steps [when the
battery’s negative (-) terminal is connected], warm
up the engine and allow it to idle for approximately
five minutes under the conditions described below,in order to stabilize the engine control conditions,
and then check to be sure that the idling is
satisfactory.
Engine coolant temperature: 80 - 95°C (176 - 203°F)
Lights, electric fans, accessories: OFF
Transaxle: neutral position(A/T models: “N” or “P”)
Steering wheel: neutral (center) position
VEHICLE WASHING
If high-pressure car-washing equipment or steam car-washing
equipment is used to wash the vehicle, be sure to maintain the
spray nozzle at a distance of at least 300 mm (12 in.) from any
plastic parts and all opening parts (doors, luggage compart-
ment, etc.).
c
TSB Revision

00-16GENERAL - Towina and Hoistina
Sling type
Wheel lift type
Flat bed type
Sling type
Wheel lift type
Flat bed typeTOWING AND HOISTING
MOOGAACWRECKER TOWING RECOMMENDATION

FRONT TOWING PICKUP
Caution
\‘i
d
This vehicle cannot be towed by a wrecker using sling-typeequipment to prevent the bumper from deformation.
If this vehicle is towed, use wheel lift or flat bed equip-
ment.The vehicle may be towed on its rear wheels for extended
distances provided the parking brake is released. It is recom-
mended that vehicles be towed using the front pickup
whenever possible.
REAR TOWING PICKUP
Caution
This vehicle cannot be towed by a wrecker using sling-typeequipment to prevent the bumper from deformation.
If this vehicle is towed, use wheel lift or flat bed equip-
\
ment.‘L*3Manual transaxle vehicles may be towed on the front wheels,
provided the transaxle is in neutral and the drive-line has not
been damaged. The steering wheel must be clamped in the
straight-ahead position with a steering wheel clamping device
designed for towing service use.
CautionDo not use steering column lock to secure front wheel
position for towing.
Automatic transaxle vehicle may be towed on the front wheels
at speeds not to exceed 50 km/h (30 mph) for a distances not to
exceed 30 km (18 miles).
CautionIf these limits cannot be met, the front wheels must be
placed on a tow dolly.
TOWING WHEN KEYS ARE NOT AVAILABLE
When a locked vehicle must be towed and keys are not
available, the vehicle may be lifted and towed from the front,
provided the parking brake is released. If not released, the rear
wheels should be placed on a tow dolly.
TSB Revision