maintenance NISSAN TEANA 2008 Repair Manual

EX-4
< ON-VEHICLE MAINTENANCE >
EXHAUST SYSTEM
ON-VEHICLE MAINTENANCE
EXHAUST SYSTEM
InspectionINFOID:0000000003793260
Check exhaust pipes, muffler and mounting for improper attachment,
leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
SMA211A

EXL-3
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
TAIL LAMP CIRCUIT .........................................74
Component Function Check ....................................74
Diagnosis Procedure ...............................................74
LICENSE PLATE LAMP CIRCUIT .....................76
Component Function Check ....................................76
Diagnosis Procedure ...............................................76
REAR FOG LAMP CIRCUIT ..............................77
Component Function Check ....................................77
Diagnosis Procedure ...............................................77
HEADLAMP SYSTEM ........................................79
Wiring Diagram - HEADLAMP - ..............................79
AUTO LIGHT SYSTEM ......................................83
Wiring Diagram - AUTO LIGHT SYSTEM - .............83
FRONT FOG LAMP SYSTEM ............................87
Wiring Diagram - FRONT FOG LAMP - ..................87
TURN SIGNAL AND HAZARD WARNING
LAMP SYSTEM ..................................................
90
Wiring Diagram - TURN AND HAZARD WARN-
ING LAMPS - ..........................................................
90
PARKING, LICENSE PLATE AND TAIL
LAMPS SYSTEM ................................................
95
Wiring Diagram - PARKING, LICENSE PLATE
AND TAIL LAMPS - .................................................
95
STOP LAMP .......................................................99
Wiring Diagram - STOP LAMP - .............................99
BACK-UP LAMP ..............................................102
Wiring Diagram - BACK-UP LAMP - .....................102
REAR FOG LAMP SYSTEM ............................105
Wiring Diagram - REAR FOG LAMP - ..................105
ECU DIAGNOSIS .......................................108
BCM (BODY CONTROL MODULE) .................108
Reference Value ...................................................108
Wiring Diagram - BCM - ........................................131
Fail-safe ................................................................137
DTC Inspection Priority Chart .............................139
DTC Index ............................................................140
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ...............
142
Reference Value ...................................................142
Wiring Diagram - IPDM E/R - ................................150
Fail-safe ................................................................153
DTC Index ............................................................155
AUTO LEVELIZER CONTROL UNIT ...............156
Reference Value ...................................................156
Wiring Diagram — HEADLAMP AIMING CON-
TROL SYSTEM — ................................................
158
Fail-safe ................................................................161
DTC Inspection Priority Chart ...............................162
DTC Index .............................................................163
SYMPTOM DIAGNOSIS ............................164
EXTERIOR LIGHTING SYSTEM SYMPTOMS .164
Symptom Table .....................................................164
NORMAL OPERATING CONDITION .............167
Description .............................................................167
BOTH SIDE HEADLAMPS (HI) ARE NOT
TURNED ON ...................................................
168
Description .............................................................168
Diagnosis Procedure .............................................168
BOTH SIDE HEADLAMPS (LO) ARE NOT
TURNED ON ...................................................
169
Description .............................................................169
Diagnosis Procedure .............................................169
PARKING, LICENSE PLATE AND TAIL
LAMPS ARE NOT TURNED ON .....................
170
Description .............................................................170
Diagnosis Procedure .............................................170
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON ...................................................
171
Description .............................................................171
Diagnosis Procedure .............................................171
PRECAUTION ............................................172
PRECAUTIONS ...............................................172
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
172
Precautions For Xenon Headlamp Service ...........172
ON-VEHICLE MAINTENANCE ..................173
HEADLAMP AIMING ADJUSTMENT .............173
Description .............................................................173
Aiming Adjustment Procedure (Low Beam) ...........174
Aiming Adjustment Procedure (High Beam) ..........175
FRONT FOG LAMP AIMING ADJUSTMENT .178
Description .............................................................178
Aiming Adjustment Procedure ...............................178
ON-VEHICLE REPAIR ...............................180
FRONT COMBINATION LAMP ......................180
Exploded View .......................................................180
Removal and Installation .......................................181
Replacement .........................................................181
Disassembly and Assembly ...................................182
FRONT FOG LAMP ........................................183
Exploded View .......................................................183
Removal and Installation .......................................183
Replacement .........................................................183

EXL-6
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON ....................................................
334
Description .............................................................334
Diagnosis Procedure .............................................334
PRECAUTION ............................................335
PRECAUTIONS ...............................................335
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................
335
ON-VEHICLE MAINTENANCE ..................336
HEADLAMP AIMING ADJUSTMENT .............336
Description .............................................................336
Aiming Adjustment Procedure (Low Beam) ...........337
Aiming Adjustment Procedure (High Beam) ..........338
FRONT FOG LAMP AIMING ADJUSTMENT .341
Description .............................................................341
Aiming Adjustment Procedure ...............................341
ON-VEHICLE REPAIR ...............................343
FRONT COMBINATION LAMP .......................343
Exploded View .......................................................343
Removal and Installation .......................................343
Replacement .........................................................344
Disassembly and Assembly ...................................344
FRONT FOG LAMP .........................................346
Exploded View .......................................................346
Removal and Installation .......................................346
Replacement .........................................................346
OPTICAL SENSOR .........................................348
Exploded View .......................................................348
Removal and Installation .......................................348
LIGHTING & TURN SIGNAL SWITCH ............349
Exploded View ......................................................349
Removal and Installation .......................................349
HEADLAMP AIMING SWITCH .........................350
Exploded View ......................................................350
Removal and Installation .......................................350
HAZARD SWITCH ............................................351
Exploded View ......................................................351
Removal and Installation .......................................351
SIDE TURN SIGNAL LAMP .............................352
Exploded View ......................................................352
Removal and Installation .......................................352
REAR COMBINATION LAMP ..........................354
Exploded View ......................................................354
Removal and Installation .......................................354
Replacement .........................................................355
HIGH-MOUNTED STOP LAMP ........................356
Exploded View ......................................................356
Removal and Installation .......................................356
REAR FOG LAMP ............................................357
Exploded View ......................................................357
Removal and Installation .......................................357
Replacement .........................................................357
LICENSE PLATE LAMP ...................................358
Exploded View ......................................................358
Removal and Installation .......................................358
Replacement .........................................................358
SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................
360
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................
360
Bulb Specifications ................................................360

EXL-172
< PRECAUTION >[XENON TYPE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003813382
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precautions For Xenon Headlamp ServiceINFOID:0000000003773614
WARNING:
Comply with the following warnings to prevent any serious accident.
 Disconnect the battery cable (negative terminal) or the power supply fuse before installing, remov-
ing, or touching the xenon headlamp (bulb included). The xenon headlamp contains high-voltage
generated parts.
 Never work with wet hands.
 Check the xenon headlamp ON-OFF status after assembling it to the vehicle. Never turn the xenon
headlamp ON in other conditions. Connect the power supply to the vehicle-side connector.
(Turning it ON outside the lamp case may cause fire or visual impairments.)
 Never touch the bulb glass immediately after turning it OFF. It is extremely hot.
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
 Install the xenon bulb securely. (Insufficient bulb socket installation may melt the bulb, the connec-
tor, the housing, etc. by high-voltage leakage or corona discharge.)
 Never perform HID circuit inspection with a tester.
 Never touch the xenon bulb glass with hands. Never put oil and grease on it.
 Dispose of the used xenon bulb after packing it in thick vinyl without breaking it.
 Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.).

HEADLAMP AIMING ADJUSTMENT
EXL-173
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003774534
PREPARATION BEFORE ADJUSTING
NOTE:
 For details, refer to the regulations in your own country.
 Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.  Adjust the tire pressure to the specification.
 Fill with fuel, engine coolant and each oil.
 Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
 Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
 Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JPLIA1085ZZ

EXL-174
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
HEADLAMP AIMING ADJUSTMENT
Aiming Adjustment Procedure (Low Beam)
INFOID:0000000003774533
1. Place the screen.
NOTE:
 Stop the vehicle at the perpendicular angle to the wall.
 Set the screen so that it is perpendicular to a level load surface.
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3. Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
A. Headlamp (LO) RH
(UP/DOWN) adjustment screwB. Headlamp (HI) RH
(UP/DOWN) adjustment screwC. Headlamp (LO) RH
(UP-OUTSIDE/DOWN-INSIDE)
adjustment screw
D. Headlamp (HI) RH
(UP-INSIDE/DOWN-OUTSIDE)
adjustment screwE. Headlamp (LO) LH
(UP/DOWN) adjustment screwF. Headlamp (HI) LH
(UP/DOWN) adjustment screw
G. H e a d l a m p ( L O ) L H
(UP-OUTSIDE/DOWN-INSIDE)
adjustment screwH. Headlamp (HI) LH
(UP-INSIDE/DOWN-OUTSIDE)
adjustment screw
: Vehicle center
Adjustment screw Screw driver rotation Facing direction
AHeadlamp (LO) RH
(UP/DOWN)Clockwise UP
Counterclockwise DOWN
BHeadlamp (HI) RH
(UP/DOWN)Clockwise UP
Counterclockwise DOWN
CHeadlamp (LO) RH
(UP-OUTSIDE/DOWN-INSIDE)Clockwise DOWN-INSIDE
Counterclockwise UP-OUTSIDE
DHeadlamp (HI) RH
(UP-INSIDE/DOWN-OUTSIDE)Clockwise DOWN-OUTSIDE
Counterclockwise UP-INSIDE
EHeadlamp (LO) LH
(UP/DOWN)Clockwise UP
Counterclockwise DOWN
FHeadlamp (HI) LH
(UP/DOWN)Clockwise UP
Counterclockwise DOWN
GHeadlamp (LO) LH
(UP-OUTSIDE/DOWN-INSIDE)Clockwise DOWN-INSIDE
Counterclockwise UP-OUTSIDE
HHeadlamp (HI) LH
(UP-INSIDE/DOWN-OUTSIDE)Clockwise DOWN-OUTSIDE
Counterclockwise UP-INSIDE

HEADLAMP AIMING ADJUSTMENT
EXL-175
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Low beam distribution on the screen
Unit: mm (in)
Aiming Adjustment Procedure (High Beam)INFOID:0000000003827917
1. Place the screen.
NOTE:
 Stop the vehicle at the perpendicular angle to the wall.
 Set the screen so that it is perpendicular to a level load surface.
JSLIA0030ZZ
A. Aiming adjustment area
B. Elbow point
C. Headlamp center
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area
(lateral)Y. Aiming adjustment area
(Vertical)
Distance from headlamp center to screen (L) : 10m (32.8 ft)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)Lateral direction (X)
(Right and left side from headlamp centerline)
Highest light axis 100 (3.94)
0-100 (3.94) Target light axis 120 (4.72)
Lowest light axis 150 (5.91)
JPLIA1062ZZ

EXL-176
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
HEADLAMP AIMING ADJUSTMENT
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3. Start the engine and illuminate the headlamp (HI).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
High beam distribution on the screen
JSLIA0030ZZ
A. Aiming adjustment area
B. Elbow point
C. Headlamp center
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area
(lateral)Y. Aiming adjustment area
(Vertical)
Distance from headlamp center to screen (L) : 10m (32.8 ft)
JPLIA1062ZZ

HEADLAMP AIMING ADJUSTMENT
EXL-177
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Unit: mm (in)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)Lateral direction (X)
(Right and left side from headlamp centerline)
Highest light axis 106 (4.17)
0-100 (3.94) Target light axis 120 (4.72)
Lowest light axis 164 (6.46)

EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
 For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
 Adjust the tire pressure to the specification.
 Fill with fuel, engine coolant and each oil.
 Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
 Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
 Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
 Turn the aiming adjusting screw for adjustment.
 For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment ProcedureINFOID:0000000003773618
1. Place the screen.
NOTE:
 Stop the vehicle facing the wall.
 Place the board on a plain road vertically.
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3. Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA1086ZZ
JPLIA0008ZZ