dimensions NISSAN TIIDA 2007 Service Service Manual

ASSEMBLY
TM-591
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
8. Install return spring (2) on parking shaft (3) and parking pawl (1)
using suitable tool.
Adjustment (1)INFOID:0000000001731449
REDUCTION PINION GEAR BEARING PRELOAD
1. Select proper thickness of reduction pinion gear adjusting shim using the following procedures.
a. Place reduction pinion gear on transaxle case as shown.
b. Install idler gear bearing outer race on transaxle case.
c. Place idler gear bearing inner race on outer race.
d. Measure dimensions “B”, “C” and “D”, and calculate dimension
“A”.
 Measure dimension “B” between the end of reduction pinion
gear and the surface of transaxle case.
Measure dimension “B” in at least two places, and take
the average.
SCIA6996E
SCIA3623E
“A”: Distance between the surface of idler gear bear-
ing inner race and the adjusting shim mating
surface of reduction pinion gear.
A = D − (B + C)
SCIA3624E
SCIA3625E

ASSEMBLY
TM-593
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
7. Measure turning torque of reduction pinion gear.
When measuring turning torque, turn reduction pinion
gear in both directions several times to seat bearing roll-
ers correctly.
If turning torque is out of specification, decrease or
increase thickness of reduction pinion gear adjusting
shim.
OUTPUT SHAFT BEARING PRELOAD
1. Select proper thickness of output gear adjusting spacer using the following procedures.
a. Remove paper rolled around output shaft.
b. Install output gear bearing outer race on bearing retainer.
c. Place bearing retainer on output shaft.
d. Place output gear bearing inner race on bearing retainer.
e. Measure dimensions “G” and “H”, and calculate dimension “F”.
 Measure dimension “G” between end of output shaft and sur-
face of output gear bearing inner race.
Measure dimension “G” in at least two places, and take
the average.Turning torque of reduction pinion gear:
Refer to XX-XX, "*****"
.
SAT190FB
SAT682D
“F”: Distance between the surface of output gear
bearing inner race and adjusting spacer mating
surface of output shaft.
F = H − G
SAT683D
SAT684D

ASSEMBLY
TM-601
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
 Measure clearance between reverse clutch drum and needle bear-
ing for oil pump cover.
 Select proper thickness of bearing race so that end play is within
specifications.
1. Measure dimensions “K” and “L”, and then calculate dimension
“J”.
a. Measure dimension “K”.
b. Measure dimension “L”.
c. Calculate dimension “J”.
2. Measure dimension “M”.
a. Place bearing race and needle bearing on oil pump assembly.
SCIA3661E
SCIA3662E
SCIA3663E
“J”: Distance between oil pump fitting surface of
transaxle case and needle bearing mating sur-
face of input shaft assembly (high clutch drum).
J = K – L
SCIA3664E
SAT378D

TM-602
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
ASSEMBLY
b. Measure dimension “M”.
c. Measure thickness of straightedge “t”.
3. Adjust total end play “T
1”.
 Select proper thickness of bearing race so that total end play
is within specifications.
REVERSE CLUTCH END PLAY
 Measure clearance between oil pump cover and thrust washer for
reverse clutch drum.
 Select proper thickness of thrust washer so that end play is within
specification.
1. Measure dimensions “O” and “P”, and then calculate dimension
“N”.“M”: Distance between transaxle case fitting surface
of oil pump cover and needle bearing on oil
pump cover.
“M
1”: Indication of gauge
SAT379D
M = M1– t
T
1 = J – M
Total end play “T
1”:
Refer to TM-324, "
Total End Play".
SAT443D
SCIA3665E
SCIA3666E

ASSEMBLY
TM-603
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
a. Place thrust washer on reverse clutch drum.
b. Measure dimension “O”.
c. Measure dimension “P”.
d. Calculate dimension “N”.
2. Measure dimensions “R” and “S”, and then calculate dimension
“Q”.
a. Measure dimension “R”.
b. Measure dimension “S”.
c. Calculate dimension “Q”.
SCIA3667E
“N”: Distance between oil pump fitting surface of
transaxle case and thrust washer on reverse
clutch drum.
N = O – P
SCIA3668E
SAT384D
SAT385D
“Q”: Distance between transaxle case fitting surface
and thrust washer mating surface.
Q = R – S
SAT386D