ignition NISSAN TIIDA 2007 Service Service Manual

AV-84
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
RGB (B: BLUE) SIGNAL CIRCUIT
RGB (B: BLUE) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728731
Transmits the image displayed with NAVI control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000001728732
1.CHECK CONTINUITY RGB (B: BLUE) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 5 and NAVI control unit harness con-
nector terminal 46.
4. Check continuity between display unit harness connector terminal 5 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (B: BLUE) SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Start “Confirmation / Adjustment Mode”, and then display color bar by selecting“Color Spectrum Bar” on
DISPLAY DIAGNOSIS screen.
4. Check signal between display unit harness connector terminal 5 and 8.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.5 - 46 : Continuity should exist.
5 - Ground : Continuity should not exist.
5 - 8
JPNIA0223ZZ

AV
RGB SYNCHRONIZING SIGNAL CIRCUIT
AV-85
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RGB SYNCHRONIZING SIGNAL CIRCUIT
DescriptionINFOID:0000000001728733
Transmits the RGB synchronizing signal to the display unit so as to synchronize the RGB image displayed
with NAVI control unit.
Diagnosis ProcedureINFOID:0000000001728734
1.CHECK CONTINUITY RGB SYNCHRONIZING SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 7 and NAVI control unit harness con-
nector terminal 48.
4. Check continuity between display unit harness connector terminal 7 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal 7 and ground.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.7 - 48 : Continuity should exist.
7 - Ground : Continuity should not exist.
7 - Ground
SKIB0825E

AV-86
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
RGB AREA (YS) SIGNAL CIRCUIT
RGB AREA (YS) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728735
Transmits the display area of RGB image displayed by NAVI control unit with RGB area (YS) signal to display
unit.
Diagnosis ProcedureINFOID:0000000001728736
1.CHECK CONTINUITY RGB AREA (YS) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 2 and NAVI control unit harness con-
nector terminal 50.
4. Check continuity between display unit harness connector terminal 2 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal 2 and ground.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.2 - 50 : Continuity should exist.
2 - Ground : Continuity should not exist.
2 - GroundAt RGB image displayed : Approx. 5 V
At rear view camera image displayed
PKIB4948J

AV
HORIZONTAL SYNCHRONIZING (HP) SIGNAL CIRCUIT
AV-87
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
HORIZONTAL SYNCHRONIZING (HP) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728737
In composite image (camera image), it transmits the vertical synchronizing (VP) signal and horizontal synchro-
nizing (HP) signal from display unit to NAVI control unit so as to synchronize the RGB images displayed with
NAVI control unit such as the image quality adjusting menu, etc.
Diagnosis ProcedureINFOID:0000000001728738
1.CHECK CONTINUITY HORIZONTAL SYNCHRONIZING (HP) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 4 and NAVI control unit harness con-
nector terminal 51.
4. Check continuity between display unit harness connector terminal 4 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK HORIZONTAL SYNCHRONIZING (HP) SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal 4 and ground.
Is inspection result OK?
YES >> Replace NAVI control unit.
NO >> Replace display unit.4 - 51 : Continuity should exist.
4 - Ground : Continuity should not exist.
4 - Ground
SKIB0825E

AV-88
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
VERTICAL SYNCHRONIZING (VP) SIGNAL CIRCUIT
VERTICAL SYNCHRONIZING (VP) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728739
In composite image (camera image), it is transmits the vertical synchronizing (VP) signal and horizontal syn-
chronizing (HP) signal from display unit to NAVI control unit so as to synchronize the RGB images displayed
with NAVI control unit such as the image quality adjusting menu, etc.
Diagnosis ProcedureINFOID:0000000001728740
1.CHECK CONTINUITY VERTICAL SYNCHRONIZING (VP) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 6 and NAVI control unit harness con-
nector terminal 52.
4. Check continuity between display unit harness connector terminal 6 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VERTICAL SYNCHRONIZING (VP) SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal 6 and ground.
Is inspection result OK?
YES >> Replace NAVI control unit.
NO >> Replace display unit.6 - 52 : Continuity should exist.
6 - Ground : Continuity should not exist.
6 - Ground
SKIB0823E

AV
STEERING SWITCH
AV-89
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
STEERING SWITCH
DescriptionINFOID:0000000001728775
When one of the steering wheel AV control switches is pushed, the resistance in the steering wheel AV control
switch circuit changes depending on which button is pushed.
Diagnosis ProcedureINFOID:0000000001728776
1.CHECK STEERING WHEEL AUDIO CONTROL SWITCH RESISTANCE
1. Disconnect steering wheel audio control switch connector M102.
2. Check resistance between steering switch connector terminals.
Do the steering wheel audio control switches check OK?
YES >> GO TO 2
NO >> Replace steering wheel audio control switch. Refer to XX-XX, "*****"
.
2.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector M42 and spiral cable con-
nector M30.
3. Check continuity between AV control unit harness connector
M42 (A) and spiral cable harness connector M30 (B).
4. Check continuity between AV control unit connector M42 (A) and ground.
Are the continuity results as specified?
YES >> GO TO 3
NO >> Repair harness.
3.SPIRAL CABLE CHECK
Terminal Signal name ConditionResistance
(Ω)
(Approx.)
16 17Seek (down)
Depress switch.165
Volume (down) Depress VOL down switch. 487
Power Depress PWR switch. 0
20 17Seek (up)
Depress switch.165
Volume (up) Depress VOL up switch. 487
Mode Depress MODE switch. 0
WKIA4457E
AB
Continuity
Connector Terminal Connector Terminal
M426
M3024
Ye s 15 31
16 32
A
—Continuity
Connector Terminal
M426
Ground No 15
16
ALNIA0332GB

AV
MICROPHONE SIGNAL CIRCUIT
AV-91
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
MICROPHONE SIGNAL CIRCUIT
DescriptionINFOID:0000000001728741
Supplies power from NAVI control unit to microphone. The microphone transmits the sound voice to the NAVI
control unit.
Diagnosis ProcedureINFOID:0000000001728742
1.CHECK HARNESS BETWEEN NAVI CONTROL UNIT AND MICROPHONE
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector and microphone connector.
3. Check continuity between NAVI control unit harness connector B68 and microphone harness connector
R15.
4. Check continuity between NAVI control unit harness connector B68 and ground.
Are the continuity test results as specified?
YES >> GO TO 2
NO >> Repair harness or connector.
2.CHECK MICROPHONE POWER SUPPLY
1. Connect NAVI control unit connector and microphone connector.
2. Turn ignition switch ON.
3. Check voltage between microphone harness connector R15 ter-
minal 4 and ground.
Is voltage reading approx. 5 volts?
YES >> GO TO 3
NO >> Replace NAVI control unit. Refer to XX-XX, "*****"
.
3.CHECK MICROPHONE SIGNAL
Check signal between NAVI control unit harness connector B68 terminals 8 and 7 with CONSULT-III or oscilli-
scope.
Te r m i n a l Te r m i n a l
Continuity
Connector Terminal Connector Terminal
B688
R151
Ye s 72
64
Te r m i n a l
— Continuity
Connector Terminal
B688
Ground No 7
6
4 - Ground : Approx. 5V
WKIA5796E

AV
AV CONTROL UNIT
AV-93
< ECU DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ECU DIAGNOSIS
AV CONTROL UNIT
Reference ValueINFOID:0000000001728761
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA0227ZZ
Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
2
(L)3
(G)Sound signal front LH OutputIgnition
switch
ONVoice output
4
(LG)5
(Y)Sound signal rear LH OutputIgnition
switch
ONVoice output
6
(R)15
(B)Steering switch signal A InputIgnition
switch
ONKeep pressing SOURCE
switch. 0 V
Keep pressing MENU UP
switch.1.2 V
Keep pressing MENU
DOWN switch.2.5 V
Keep pressing ENTER
switch.3.7 V
Except for above. 5 V
7
(R)Ground ACC power supply InputIgnition
switch
ACC−Battery voltage
8
(B)Ground GND —Ignition
switch
ON—0 V
9
(R)Ground Illumination signal Input OFFLighting switch is OFF. 0 V
Lighting switch is ON. 12 V
SKIB3609E
SKIB3609E

AV-94
< ECU DIAGNOSIS >[AUDIO WITH NAVIGATION]
AV CONTROL UNIT
11
(BR)12
(P)Sound signal front RH OutputIgnition
switch
ONVoice output
13
(O)14
(V)Sound signal rear RH OutputIgnition
switch
ONVoice output
15
(B)Ground Steering switch signal GND —Ignition
switch
ON—0 V
16
(Y)15
(B)Steering switch signal B InputIgnition
switch
ONKeep pressing VOL DOWN
switch.0 V
Keep pressing VOL UP
switch.1.2 V
Keep pressing
switch.2.5 V
Keep pressing switch.3.7 V
Except for above. 5 V
19
(LG)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
20
(B)Ground GND —Ignition
switch
ON—0 V
23
(L)—AV communication signal
(H)Input/
Output—— —
24
(P)—AV communication signal
(L)Input/
Output—— —
30
(W)31
(O)TEL voice signal InputIgnition
switch
ONTEL voice output
32
(O)33
(W)Voice guidance signal InputIgnition
switch
ONVoice guidance output Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E

AV-100
< ECU DIAGNOSIS >[AUDIO WITH NAVIGATION]
NAVI CONTROL UNIT
NAVI CONTROL UNIT
Reference ValueINFOID:0000000001728758
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III data monitor item
TERMINAL LAYOUT
PHYSICAL VALUES
Display ItemDis-
playVehicle status Remarks
VHCL SPD SIGON Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is
normal.
OFF Vehicle speed =0 km/h (0 MPH)
PKB SIGON Parking brake is applied.
Changes in indication may be delayed. This is
normal.
OFF Parking brake is released.
ILLUM SIGON Lighting switch ON
—
OFF Lighting switch OFF
IGN SIGON Ignition switch ON
—
OFF Ignition switch in ACC position
REV SIGON Selector lever in R position
Changes in indication may be delayed. This is
normal.
OFFSelector lever in any position other
than R
JPNIA0226ZZ
Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(B)Ground GND —Ignition
switch
ON—0 V
2
(LG)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
5
(R)Ground ACC power supply InputIgnition
switch
ACC— Battery voltage
6
(B)7 Microphone VCC OutputIgnition
switch
ON—5 V
7 Ground Microphone GND —Ignition
switch
ON—0 V