check engine light NISSAN TIIDA 2007 Service Manual PDF

EC-1158
< COMPONENT DIAGNOSIS >[K9K]
P0409 EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR
P0409 EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR
DTC LogicINFOID:0000000001162623
DTC DETECTION LOGIC
NOTE:
If DTC P0409 is displayed with DTC P0651, first perform trouble diagnosis for DTC P0651. Refer to
EC-1182, "
DTC Logic".
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after the engine started.
If the DTC is present:
-Malfunction indicator (Yellow) lights up.
Diagnosis ProcedureINFOID:0000000001162624
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR POWER SUPPLY CIRCUIT
1. Disconnect EGR volume control valve harness connector.
2. Turn ignition switch ON.
3. Check the voltage between EGR volume control valve control position sensor connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR GROUND CIRCUIT FOR
OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between EGR volume control valve control position sensor harness connector and
ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
DTC No. Trouble diagnosis name Possible Cause
P0409EGR VOLUME CONTROL VALVE CONTROL POSITION SEN-
SOR CIRCUIT
 CO.0: Open circuit or short circuit to ground
 CC.1: Short circuit to +12V Harness or connectors
(The EGR volume control valve control position
sensor circuit is open or shorted.)
 EGR volume control valve control position sensor
EGR volume control valve control position sensor
Ground Voltage
Connector Terminal
F52 1 Ground Approx. 5V
EGR volume control valve control posi-
tion sensorECM
Continuity
Connector Terminal Connector Terminal
F52 3 E16 82 Existed

EC-1162
< COMPONENT DIAGNOSIS >[K9K]
P0488 EGR SYSTEM
P0488 EGR SYSTEM
DTC LogicINFOID:0000000001162628
DTC DETECTION LOGIC
NOTE:
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after the engine is started.
Special notes:
- Engine instability, possibly even stalling.
- Difficult to start engine or even impossible when cold.
- Loss of performance.
- Possible smoke emissions.
-Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162629
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EGR VOLUME CONTROL VALVE INSTALLATION
Check that EGR volume control valve is installed properly.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Install EGR volume control valve properly.
3.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR POWER SUPPLY CIRCUIT
1. Disconnect EGR volume control valve harness connector.
2. Turn ignition switch ON.
3. Check the voltage between EGR volume control valve control position sensor connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR GROUND CIRCUIT FOR
DTC No. Trouble diagnosis name Possible cause
P0488EGR VOLUME CONTROL
 1.DEF: Signal incoherence
 2.DEF: Signal outside lower level
 3.DEF: Signal outside upper level
 4.DEF: Valve outside level
 5.DEF: Defective sensor Harness or connectors
(The EGR volume control valve circuit is open
or shorted.)
(The EGR volume control valve control posi-
tion sensor circuit is open or shorted.)
 EGR volume control valve
 EGR volume control valve control position
sensor
 Incorrect EGR volume control valve installa-
tion
 EGR volume control valve stuck closed
 EGR passage clogged
GR volume control valve control position sensor
Ground Voltage
Connector Terminal
F52 1 Ground Approx. 5V

EC-1178
< COMPONENT DIAGNOSIS >[K9K]
P0606 ECM
P0606 ECM
DescriptionINFOID:0000000001162646
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC LogicINFOID:0000000001162647
DTC DETECTION LOGIC
NOTE:
If DTC P0606 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC is declared present after an attempted start, or with the engine running.
If the DTC is present:
-Malfunction indicator (Red) lights up.
-Malfunction indicator (Yellow) lights up.
Diagnosis ProcedureINFOID:0000000001162648
1.CHECK DTC
Make sure that which malfunction (DTC second line indication) is displayed.
A or B
A>>GO TO 2.
B>>GO TO 3.
2.REPLACE ECM
1. Perform EC-1054, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
Requirement".
2. Perform EC-1055, "
EGR VOLUME CONTROL VALVE CLOSED POSITION LEARNING : Special Repair
Requirement".
>>INSPECTION END
3.CHECK CAN COMMUNICATION LINE
Refer to LAN-33, "
CAN Communication Signal Chart".
OK or NG
OK >> GO TO 4.
NG >> Repair or replace.
4.CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
MBIB1517E
DTC No. Trouble diagnosis name Possible cause
P0606ECM
 1.DEF to 20.DEF: Internal electric malfunctionECM
AExcept 9.DEFF
B9.DEF

EC-1186
< COMPONENT DIAGNOSIS >[K9K]
P1089 FUEL PUMP
P1089 FUEL PUMP
DTC LogicINFOID:0000000001162661
DTC DETECTION LOGIC
NOTE:
NOTE:
-If DTC P1089 is displayed with DTC P0180, first perform trouble diagnosis for DTC P0180. Refer to
EC-1136, "
DTC Logic".
-If DTC P1089 is displayed with DTC P0190, first perform trouble diagnosis for DTC P0190. Refer to
EC-1138, "
DTC Logic".
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC appears when the engine is running.
If the DTC is present:
-Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162662
1.CHECK LOW PRESSURE FUEL SUPPLY SYSTEM
Refer to EC-1043, "
BASIC INSPECTION : Special Repair Requirement (TEST 1: Low Pressure Fuel Supply
System Check)".
Is the inspection result normal?
OK >> GO TO 2.
NG >> Replace or replace. Then GO TO 9.
2.CHECK INTERNAL FUEL TRANSFER PUMP
Refer to EC-1044, "
BASIC INSPECTION : Special Repair Requirement (TEST 2: Internal Fuel Transfer Pump
Check)".
Is the inspection result normal?
OK >> GO TO 3.
NG >> Replace or replace. Then GO TO 9.
3.CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)
Refer to EC-1044, "
BASIC INSPECTION : Special Repair Requirement [TEST 3: High Pressure Supply Pump
(Pressure Control Valve) Check]".
Is the inspection result normal?
OK >> GO TO 4.
NG >> Replace or replace. Then GO TO 9.
DTC No. Trouble diagnosis name Possible cause
P1089FUEL RAIL PRESSURE REGULATION FUNCTION
 1.DEF: High pressure supply pump (Pressure control valve) closed
 2.DEF: High pressure supply pump (Pressure control valve) open
 3.DEF: High pressure supply pump (Volumetric control valve) open
 4.DEF: High pressure supply pump (Volumetric control valve) closed
 5.DEF: Component malfunction: High pressure supply pump (Pressure
control valve or Volumetric control valve)
 6.DEF: High pressure supply pump (Pressure control valve) oscillation
 7.DEF: High pressure supply pump (Volumetric control valve)) oscilla-
tion Harness or connectors
[High pressure supply pump (volumetric
control valve) circuit is open or shorted.]
[High pressure supply pump (Pressure
control valve) circuit is open or shorted.]
(Fuel rail pressure sensor circuit is open or
shorted.)
 High pressure supply pump
 High pressure supply pump (Pressure
control valve)
 High pressure supply pump (Volumetric
control valve)
 Fuel line
 Fuel rail
 Fuel injector
 Fuel rail pressure sensor
 Fuel rail pressure relief valve
 Air mixture with fuel
 Lack of fuel

P2120 APP SENSOR
EC-1191
< COMPONENT DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
P2120 APP SENSOR
DescriptionINFOID:0000000001162667
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensors detect the accelera-
tor pedal position and sends a signal to the ECM. The ECM uses the
signal to determine the amount of fuel to be injected.
DTC LogicINFOID:0000000001162668
DTC DETECTION LOGIC
NOTE:
If DTC P2120 is displayed with DTC P0641, first perform trouble diagnosis for DTC P0641. Refer to
EC-1180, "
DTC Logic".
 Conditions for applying the diagnostic procedure to the stored DTCs:
- The DTC is declared present after a series of full load-no load accelerator pedal actions have been carried
out (engine stopped, ignition on).
If the DTC is present:
-Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162669
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK ACCELERATOR PEDAL POSITION SENSOR POWER SUPPLY CIRCUIT
1. Disconnect accelerator pedal position sensor harness connector.
2. Turn ignition switch ON.
3. Check the voltage between accelerator pedal position sensor connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
PBIB1741E
DTC No. Trouble diagnosis name Possible cause
P2120ACCELERATOR PEDAL POSITION SENSOR 2 CIRCUIT
 CC.1: Short circuit to +12V
 CO.0: Open circuit or short circuit to ground Harness or connectors
(APP sensor 2 circuit is open or shorted.)
 Accelerator pedal position sensor
(APP sensor 2)
Accelerator pedal position sensor
Ground Voltage
Sensor Connector Terminal
2E12 (LHD models)
M204 (RHD models)5 Ground Approx. 5V

P2263 TC SYSTEM
EC-1195
< COMPONENT DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
P2263 TC SYSTEM
DTC LogicINFOID:0000000001162674
DTC DETECTION LOGIC
NOTE:
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC becomes present after the engine is started.
If the DTC is present:
Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162675
1.CHECK VACUUM HOSES AND VACUUM GALLERY
1. Turn ignition switch OFF.
2. Check vacuum hoses and vacuum gallery for clogging, cracks
or improper connection. Refer to EC-1070, "
Vacuum Hose
Drawing".
Is the inspection result normal?
Yes >> Repair or replace.
No >> GO TO 2.
2.CHECK AIR FILTER
Check that air filter is not obstructed.
Is the inspection result normal?
Yes >> Repair or replace.
No >> GO TO 3.
3.CHECK INTAKE AIR DUCT
Check that intake air duct is not obstructed.
Is the inspection result normal?
Yes >> Repair or replace.
No >> GO TO 4.
4.CHECK VACUUM PUMP
Check vacuum pump.
Is the inspection result normal?
Yes >> Repair or replace.
No >> GO TO 5.
5.CHECK TURBOCHARGER
DTC No. Trouble diagnosis name Possible cause
P2263AIR INLET CIRCUIT
 1.DEF: Permanent at minimum limit
 2.DEF: Permanent at maximum limit Harness or connectors
(Turbocharger boost control solenoid valve circuit
is open or shorted.)
 Air inlet circuit
 Vacuum pump
 Vacuum hose
 Turbocharger
 Turbocharger boost control solenoid valve
 Turbocharger boost sensor
 Electric throttle control actuator
SEF109L

EC-1202
< COMPONENT DIAGNOSIS >[K9K]
P2413 EGR SYSTEM
P2413 EGR SYSTEM
DTC LogicINFOID:0000000001162678
DTC DETECTION LOGIC
NOTE:
Conditions for applying the diagnostic procedure to the stored DTCs:
The DTC becomes present after the engine is started.
Special notes:
- Engine instability, possibly even stalling.
- Difficult to start engine or even impossible when cold.
- Loss of performance.
- Possible smoke emissions.
If the DTC is present:
-Malfunction indicator (Red) lights up.
Diagnosis ProcedureINFOID:0000000001162679
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground inspection in GI-58, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EGR VOLUME CONTROL VALVE INSTALLATION
Check that EGR volume control valve is installed properly.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Install EGR volume control valve properly.
3.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR POWER SUPPLY CIRCUIT
1. Disconnect EGR volume control valve harness connector.
2. Turn ignition switch ON.
3. Check the voltage between EGR volume control valve control position sensor connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK EGR VOLUME CONTROL VALVE CONTROL POSITION SENSOR GROUND CIRCUIT FOR
DTC No. Trouble diagnosis name Possible cause
P2413EGR VOLUME CONTROL
 1.DEF: Jammed component Harness or connectors
(The EGR volume control valve circuit is open
or shorted.)
(The EGR volume control valve control posi-
tion sensor circuit is open or shorted.)
 EGR volume control valve
 EGR volume control valve control position
sensor
 Incorrect EGR volume control valve installa-
tion
 EGR volume control valve stuck closed
 EGR passage clogged
GR volume control valve control position sensor
Ground Voltage
Connector Terminal
F52 1 Ground Approx. 5V

EC-1214
< COMPONENT DIAGNOSIS >[K9K]
STOP LAMP SWITCH
STOP LAMP SWITCH
DescriptionINFOID:0000000001162692
Brake switch signal is applied to the ECM through the stop lamp switch when the brake pedal is depressed.
This signal is used mainly to decrease the engine speed when the vehicle is driving.
Component Function CheckINFOID:0000000001162693
1.CHECK BRAKE SWITCH FUNCTION
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Go to EC-1214, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001162694
1.CHECK BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Turn ignition switch ON.
4. Check the voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.DETECT MALFUNCTIONING PART
Check the following.
 Harness connectors M69, E7 (LHD models)
 Harness connectors M25, M201 (RHD models)
 10A fuse (No. 7)
 Harness for open or short between fuse and stop lamp switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK BRAKE SWITCH INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between stop lamp switch harness connector and ECM harness connector.
+–
Condition Voltage
Connector Terminal Connector Terminal
E1611 5
(Brake switch signal)E16 128Brake ped-
alFully released 0V
Slightly depressed Battery voltage
Stop lamp switch
Ground Voltage
Connector Terminal
E13 (LHD models)
M203 (RHD models)1 Ground Battery voltage

ECM
EC-1223
< ECU DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Conformity CheckINFOID:0000000001538653
MAIN SCREEN
111
B—ASCD steering switch
ground—— —
11 5
(R)128
(B)Stop lamp switch —[Ignition switch: OFF]
 Brake pedal: Fully releasedApproximately 0V
[Ignition switch: OFF]
 Brake pedal: Slightly de-
pressedBATTERY VOLTAGE
(11 - 14V)
11 6
(GR)128
(B)ASCD brake switch Input[Ignition switch: ON]
 Brake pedal: Slightly de-
pressedApproximately 0V
[Ignition switch: ON]
 Brake pedal: Fully releasedBATTERY VOLTAGE(11 - 14V)
11 8
(SB)120
(Y)Sensor power supply
(Accelerator pedal position
sensor 2)—[Ignition switch: ON]Approximately 5V
11 9
(GR)120
(Y)Accelerator pedal position
sensor 2Input[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully re-
leased0.3 - 0.6V
[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully de-
pressed1.95 - 2.4V
120
(Y)—Sensor ground
(Accelerator pedal position
sensor 2)—— —
122
(P:
LHD)
(O:
RHD)127
(R)Sensor power supply
(Accelerator pedal position
sensor 1)—[Ignition switch: ON]Approximately 5.0V
123
(B)
124
(B)
125
(B)
128
(B)— ECM ground — — —
126
(G)127
(R)Accelerator pedal position
sensor 1Input[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully re-
leased0.6 - 0.9V
[Ignition switch ON]
 Engine stopped
 Accelerator pedal: Fully de-
pressed3.9 - 4.7V
127
(R)—
Sensor ground
(Accelerator pedal position
sensor 1)—— — Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal nameInput/
Output

ECM
EC-1229
< ECU DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
DRIVER PARAMETERS SUB FUNCTION
Test Condition: Engine Stopped and Ignition Switch ON
Test Condition: Engine at Idle
7Intake air tempera-
tureAIR TEMP SEN V 0.1V < AIR TEMP SEN V < 4.8VIn the event of a malfunction, per-
form the trouble diagnosis for DTC
P0110 IAT SENSOR.
8 Fuel injectorsINJCTR CONDNSR V49V < INJCTR CONDNSR V <
96V
In the event of a malfunction, per-
form the trouble diagnosis for
P0201, P0202, P0203 and P0204
FUEL INJECTOR. COMM INJCTR CYL1
ACTIVE COMM INJCTR CYL2
COMM INJCTR CYL3
COMM INJCTR CYL4 Order Function Parameter Display and notes Trouble diagnosis
Order Function Parameter Display and notes Trouble diagnosis
1 Power supply C/U+AFTR IGN PRESENT NONE
2 Clutch pedal ACC PEDAL DETECT NOIn the event of a malfunction, per-
form the trouble diagnosis for
ASCD CLUTCH SWITCH.
3Malfunction indica-
torSEVERITY 1 LIGHT INACTIVE
Also check that there are no mal-
function ECM.
SEVERITY 2 LIGHT INACTIVE
4 Accelerator pedalACCEL/PDL POS0% = ACCEL/PDL POS < 100%
Indicates the percentage of the
accelerator pedal position be-
tween no load and full load posi-
tion.
In the event of a malfunction, per-
form the trouble diagnosis for APP
SENSOR (DTC P0225, and
P2120) and SENSOR POWER
SUPPLY (DTC P0641 and P0651). PEDAL POS TRACK1 Indicates the percentage of the
accelerator pedal position be-
tween no load and full load posi-
tion.
PL PTNMR T1 V0.4V < PL PTNMR T1V < 4.64V
Indicates the percentage of the
accelerator pedal position be-
tween no load (0V) and full load
(5V) position.
PEDAL POS TRACK2 Indicates the percentage of the
accelerator pedal position be-
tween no load and full load posi-
tion.
PL PTNMR T2 V0.27V < PL PTNMR T2V < 3.75V
Indicates the percentage of the
accelerator pedal position be-
tween no load (0V) and full load
(5V) position.
Order Function Parameter Display and notes Trouble diagnosis
1 Power supply C/U+AFTR IGN PRESENT NONE
2 Clutch pedal ACC PEDAL DETECT NOIn the event of a malfunction, per-
form the trouble diagnosis for
ASCD CLUTCH SWITCH.
3 Malfunction indicatorSEVERITY 1 LIGHT INACTIVE
Also check that there are no mal-
function ECM.
SEVERITY 2 LIGHT INACTIVE