RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Workshop Manual
Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 391
Page 371 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -371
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -371V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP46 Steering lock fails
NOTESCheck for any faults on the steering lock.
Check the battery voltage. It should be between 9 V and 16 V.
Check the validity of parameter PR008 "Vehicle speed".
Check for any faults in the Airbag computer (impact detected) and ABS/ESP
computers.
Reminder: In hands-free mode, the steering column lock is locked as soon as the
ignition is switched off.
With the card in the reader, the steering column lock is locked after the ignition is
switched off as soon as the card is removed from the reader.
The conditions for a drop in + after ignition feed without the steering column locking are:
–the card is present in the card reader,
–over 20 minutes passing with the card in the card reader after the engine has stopped,
–the vehicle speed is not zero,
–power being requested by the steering column lock too frequently.
With regard to vehicles fitted with UCH computer Vdiag 4F or above:
–the Renault card is removed from the card reader when the vehicle is in forced + after ignition feed,
–3 mins have elapsed following a starting failure due to an engaged gear,
–the Renault card is removed from the card reader following a starting failure due to an engaged gear,
–a front door is open following a starting failure due to an engaged gear and the card is not in the reader.
Check that these conditions are not present.
Check the consistency of statuses ET072 Steering column lock and ET073 Steering column lock signal.
In the event of a fault, see the procedure for these statuses in the UCH section.
Check that the steering column lock belongs to the vehicle using status ET248 Steering column lock immobiliser
code.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP46 /UCH_V48_ALP46/UCH_V4C_ALP46/
UCH_V4D_ALP46/UCH_V4F_ALP46/UCH_V50_ALP46
Page 372 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -372
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -372V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP47 Steering column lock does not unlock
NOTES–The immobiliser warning light flashes normally,
–the card reader does not flash,
–there is a message on the instrument panel Column not unlocked or Turn
steering wheel + Start.
Check that the steering column is not under any mechanical stress (e.g.: wheel(s) jammed against pavement).
If the steering column is under stress, try to start the vehicle again by lifting the steering column (and pulling the
card out of the reader if a message requests this).
Check the consistency of statuses ET072 Steering column lock and ET073 Steering column lock signal.
In the event of a fault, see the procedure for these statuses in the UCH section.
Check that the steering column lock belongs to the vehicle using status ET248 Steering column lock immobiliser
code.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP47 /UCH_V48_ALP47/UCH_V4C_ALP47/
UCH_V4D_ALP47/UCH_V4F_ALP47/UCH_V50_ALP47
Page 373 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -373
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -373V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
Manual gearbox
Automatic gearbox
ALP48 Erratic starting
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Make sure that the clutch pedal switch is working correctly.
To do this, check the consistency of status ET048 Clutch pedal position in the UCH.
In the event of a problem, use the fault-finding procedure DF003 "Clutch switch circuit".
Make sure that the brake pedal switch is working correctly.
To do this, check the consistency of status ET047 Brake pedal position in the UCH.
In the event of a problem, use the fault-finding procedure DF004 "Brake light switch circuit".
Make sure that the gear selector lever is working correctly.
To do this, check the consistency of status ET005 Manual gearbox lever position in the Protection and Switching
Unit.
In the event of a fault, use the fault finding procedure for status ET005.
If the fault is still present, contact the Techline.
Make sure that the brake pedal switch is working correctly.
To do this, check the consistency of status ET047 Brake pedal position in the UCH.
In the event of a problem, use the fault-finding procedure DF004 "Brake light switch circuit".
Make sure that the clutch pedal switch is working correctly.
Particularly by checking the consistency of status ET108 Automatic transmission lever position in the UCH.
In the event of a fault, use fault finding procedure for status ET108.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP48 /UCH_V48_ALP48/UCH_V4C_ALP48/
UCH_V4D_ALP48/UCH_V4F_ALP48/UCH_V50_ALP48
Page 374 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -374
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -374V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP49 No folding-in or folding-out of one or more door mirrors
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check for + 12 V on the mirror switch control.
Is there+ 12 V?
Check for earth on the door mirror switch.
Repair if necessary.
Check the continuity between the following
connections:
For folding-in:
●Connection code BCP3.
●Connection code 40X of component 134.
●Connection code MAM.
●Connection code 40W of component 134.
for folding-out:
●Connection code MAM.
●Connection code 40X of component 134.
●Connection code BCP3.
●Connection code 40W of component 134.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the mirror power supply fuse.
Replace it if necessary.
Replace the switch if necessary.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP49 /UCH_V48_ALP49/UCH_V4C_ALP49/
UCH_V4D_ALP49/UCH_V4F_ALP49/UCH_V50_ALP49
Page 375 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -375
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -375V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP49
CONTINUED
Check the continuity and insulation of the following connections:
●Connection code 40W.
●Connection code 40X between components 134 and 239.
●Connection code 40W.
●Connection code 40X of component 134 and 240.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the door mirror(s).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 376 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -376
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -376V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP50 Cannot adjust one of the two door mirrors
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Non-retractable door mirror.
Left-hand door mirror.
Check the continuity between the following
connections:
Tilt up:
●Connection code 40C.
●Connection code BCP3 of component 134.
●Connection code MAM.
●Connection code 40E of component 134.
Tilt down:
●Connection code 40C.
●Connection code MAM of component 134.
●Connection code BCP3.
●Connection code 40E of component 134.
Replace the switch if necessary.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP50 /UCH_V48_ALP50/UCH_V4C_ALP50/
UCH_V4D_ALP50/UCH_V4F_ALP50/UCH_V50_ALP50
Page 377 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -377
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -377V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP50
CONTINUED 1
Check the continuity between the following
connections:
Tilt left:
●Connection code 40A.
●Connection code BCP3 of component 134.
●Connection code MAM.
●Connection code 40E of component 134.
Tilt right:
●Connection code 40A.
●Connection code 40B of component 134.
●Connection code BCP43.
●Connection code 40E of component 134.
Check the continuity and insulation of the
following connections:
●Connection code 40C.
●Connection code 40A.
●Connection code 40E between components
134 and 239.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the door mirror(s).
Replace the switch if necessary.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 378 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -378
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -378V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP50
CONTINUED 2
Non-retractable door mirror. Right-hand door mirror.
Check the continuity between the following
connections:
Tilt up:
●Connection code 40B.
●Connection code BCP3 of component 134.
●Connection code MAM.
●Connection code 40E of component 134.
Tilt down:
●Connection code 40B.
●Connection code MAM of component 134.
●Connection code BCP3.
●Connection code 40E of component 134.
Tilt left:
●Connection code 40D.
●Connection code BCP3 of component 134.
●Connection code MAM.
●Connection code 40E of component 134.
Tilt right:
●Connection code 40D.
●Connection code MAM of component 134.
●Connection code BCP43.
●Connection code 40E of component 134.
Replace the switch if necessary.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 379 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -379
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -379V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP50
CONTINUED 3
Check the continuity and insulation of the following connections:
●Connection code 40B.
●Connection code 40D.
●Connection code 40E between components 134 and 240.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the door mirror(s).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 380 of 391

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -380
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -380V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP50
CONTINUED 4
Retractable door mirror. Left-hand door mirror.
Check the continuity on the switch between the
following connections:
Tilt up:
●Connection code 40C.
●Connection code BCP3 of component 134.
●Connection code MAM.
●Connection code 40E of component 134.
Tilt down:
●Connection code 40C.
●Connection code MAM of component 134.
●Connection code BCP3.
●Connection code 40E of component 134.
Replace the switch if necessary.
AFTER REPAIRCarry out a complete check with the diagnostic tool.