SSANGYONG KORANDO 1997 Service Repair Manual

LIGHTING SYSTEM 9B-17
SSANGYONG MY2002
KAA9B070
REAR COMBINATION LAMPS
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the screws and the lamp assembly
3. Remove any inoperative bulb.
4. Installation should follow the removal procedure
in the reverse order.
KAA9B100
FOG LAMPS
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the bolts that secure the fog lamp
assembly
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Remove the fog assembly.
4. Disconnect the fog lamp assembly electrical
connector.
Tightening Torque5 - 9 Nm
(44 - 80 lb-in)
KAA9B110
5. Remove the fog lamp dust cover.
6. Remove the locking clip.
7. Remove the bulb fromthefog lamp assembly.
8. Disconnect the bulb electrical connector.
9. Installation should follow the removal procedure
in the reverse order.

SSANGYONG MY2002
9B-18 LIGHTING SYSTEM
KAA9B130
KAA9B140
4. Disconnect the electrical connector.
5. Remove the bulb.
6. Installation should follow the removal procedure
in the reverse order.
INTERIOR COURTESY LAMP
(Front Room Lamp Shown, Center Room
Lamp Similar)
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Pry off the room lamp lens by inserting a screw
driver into the recess along the edge of the lens.
3. Remove the screws and the room lamp housing
from the headliner.
KAA9B160
3. Disconnect the electrical connector.
4. Remove the bulb.
5. Installation should follow the removal procedure
in the reverse order.
KAA9B150
DOOR COURTESY LAMP
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Pry off the door courtesy lamp assembly by
inserting a flat driver.

LIGHTING SYSTEM 9B-19
SSANGYONG MY2002
KAA9B170
KAA9B180
4. Disconnect the electrical connector.
5. Remove the bulb.
6. Installation should follow the removal procedure
in the reverse order.
LUGGAGE LAMP
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Open the tail gate.
3. Pry off the luggage lamp assembly by inserting a
flat driver.
KAA9B120
LICENSE PLATE LAMPS
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the screws and the license plate lamp
assembly.
3. Remove the license plate lamps
4. Installation should follow the removal procedure
in the reverse order.

SSANGYONG MY2002
9B-20 LIGHTING SYSTEM
SPECIFICATIONS
BULB USAGE CHART
FASTENER TIGHTENING SPECIFICATIONS
Headlamp High/Low
Turn Signal Lamp
Position Lamp
Front Side Maker Lamp
Tail Lamp
Stop Lamp
Rear Trun Signal Lamp
Back Up Lamp
Front Fog Lamp
Rear Side Maker Lamp
License Plate Lamp
Center High-Mounted Stop Lamp
Front Interior Room Lamp
Second Interior Room Lamp
Luggage LampBulbReplacement Bulb Number65 w / 45 w
28 w
8 w
8 w
8 w
27 w
27 w
27 w
55 w
5 w
5 w
27 w
8 w
10 w
5 w
Front Combination Lamp Mounting Nuts
Fog Lamp Mounting Bolts
Headlamp Mounting Bolts
Radiator Mounting RivetApplication
Nm
5 - 9
5 - 9
5 - 9
2 - 5-
-
-
-44 - 80
44 - 80
44 - 80
18 - 44 Lb-FtLb-In

LIGHTING SYSTEM 9B-21
SSANGYONG MY2002
SCHEMATIC AND ROUTING DIAGRAMS
HEAD LAMP LEVELING DEVICE (HLLD) : GASOLINE
KAA9B190

SSANGYONG MY2002
9B-22 LIGHTING SYSTEM
HEAD LAMP LEVELING DEVICE (HLLD) : DIESEL
KAA9B200

LIGHTING SYSTEM 9B-23
SSANGYONG MY2002
TAIL LAMP RELAY CIRCUIT POSITION LAMP, TAIL LAMP, LICENSE LAMP
KAA9B210

SSANGYONG MY2002
9B-24 LIGHTING SYSTEM
ILLUMINATION SWITCH
KAA9B220

LIGHTING SYSTEM 9B-25
SSANGYONG MY2002
TURN SIGNAL LAMP
KAA9B230

SSANGYONG MY2002
9B-26 LIGHTING SYSTEM
FRONT FOG LAMP
KAA9B240