SUZUKI SWIFT 2000 1.G Transmission Service Workshop Manual

AUTOMATIC TRANSMISSION (4 A/T) 7B-129
44) Apply grease to thrust needle roller bearing (1) and install it.
“A” : Grease 99000-25030
45) Apply grease to clutch drum thrust washer (1) and install it to
oil pump assembly (2).
“A” : Grease 99000-25030
46) Install new gasket to transmission case and install oil pump
assembly (1) to transmission case.
Tightening torque
Oil pump assembly bolts (a) : 12 N·m (1.2 kg-m, 9.0 lb-ft)
47) Measure input shaft end (2) play.
Set dial gauge (1) as shown in figure and measure the play
of the input shaft.
Input shaft end Play
Standard : 0.3 – 0.7 mm (0.012 – 0.028 in.)
48) If the obtained value is out of standard value, select thrust
bearing race (installed in step 41)) of different thickness
shown in table below and adjust the play.
Available thrust bearing race size (thickness)
1.3 mm (0.051 in.), 1.7 mm (0.067 in.) or 2.1 mm (0.083 in.)
3. Oil pump

7B-130 AUTOMATIC TRANSMISSION (4 A/T)
49) Install differential gear assembly (1).
50) Install thrust bearing race (1) and thrust needle roller bearing
(2) to the top of counter driven gear (3).
51) Apply grease to oil pump D-ring.
Install new gasket to transmission case and install torque
converter housing (1).
Tightening torque
Torque converter housing bolts
(h) : 19 N·m (1.9 kg-m, 14.0 lb-ft)
Grease 99000-25030
“A” : Thread lock cement 99000-32110 NOTE:
Grease can be applied around the R and L bearing of dif-
ferential gear assembly to ease fitting to the transmis-
sion case and torque converter housing.
NOTE:
Apply thread lock to the three bolts shown in figure.
2. New bolt

AUTOMATIC TRANSMISSION (4 A/T) 7B-131
52) Install O-rings to each accumulator piston and apply grease
or ATF to them.
Grease 99000-25030
53) Install C1 and B0 accumulator pistons (1 and 6), springs (2,
3 and 7) and spacers (4).
Hold them with snap rings (5).
54) Install C0, B1, C2 accumulator springs (9, 12, 13, 15 and
16), spacer (11) and pistons (8, 10 and 14) as shown in fig-
ure.
55) Install wire-to-solenoid assembly (1).
Tightening torque
Wire - to - solenoid assembly bolt
(a) : 8 N·m (0.8 kg-m, 6.0 lb-ft)
Grease 99000-25030 NOTE:
C1 and B0 accumulator pistons are the same.
NOTE:
 Make sure that snap rings are fitted to the groove of
each cylinder.
 Make sure that O-rings are not twisted or caught when
installing.
NOTE:
Make sure that O-rings are not twisted or caught when
installing.
1. C1 accumulator piston 9. C0 accumulator spring
(with Pink paint)
2. C1 accumulator outer spring
(with Yellow paint)10. B1 accumulator piston
3. C1 accumulator inner spring
(with Yellow paint)11. B1 accumulator spacer
4. Spacer 12. B1 accumulator inner spring
(with Orange paint)
5. Snap ring 13. B1 accumulator outer spring
(with Orange paint)
6. B0 accumulator piston 14. C2 accumulator piston
7. B0 accumulator spring
(with Purple paint)15. C2 accumulator inner spring
(with Light Blue paint)
8. C0 accumulator piston 16. C2 accumulator outer spring
(with Light Blue paint)
NOTE:
Apply grease to O-ring of wire-to-solenoid assembly.

7B-132 AUTOMATIC TRANSMISSION (4 A/T)
56) Install valve body assembly (1) to transmission case.
First match the pin of the manual valve to the slot of the
manual shift shaft.
To fix valve body assembly (1) to transmission case, first
tighten bolt B (3), then tighten other bolts.
Tightening torque
Valve body to transmission case bolts
: 10 N·m (1.0 kg-m, 7.5 lb-ft)
57) Connect couplers of wire-to-solenoid to solenoid valves.Bolt Length “a”Pieces
A 30 mm (1.20 in.) 7
B 31 mm (1.22 in.) 2
C 25 mm (0.98 in.) 2
2. Bolt A
4. Bolt C
5. Manual valve pin
6. Slot of manual shift shaft
Solenoid Valve Wire Color
A (No.1) White
B (No.2) Black
C (No.3) Red
D (No.4) Yellow
E (No.5) Brown
TCC (Lock-up) Orange
1. Solenoid valve No.1
2. Solenoid valve No.2
3. Solenoid valve No.3
4. Solenoid valve No.4
5. Solenoid valve No.5
6. Lock-up solenoid

AUTOMATIC TRANSMISSION (4 A/T) 7B-133
58) Install O-ring to oil strainer assembly (1). Make sure that O-
ring is not twisted.
59) Install oil strainer assembly to the top of valve body assem-
bly.
Connect transmission temperature sensor (2) coupler.
Fix transmission temperature sensor and oil strainer assem-
bly with bolts.
Tightening torque
Transmission temperature sensor bolt
(a) : 10 N·m (1.0 kg-m, 7.5 lb-ft)
60) Install magnet (1) in oil pan (2).
61) Install gasket to transmission case and install oil pan (1).
Tightening torque
A/T oil pan bolts (a) : 7.5 N·m (0.75 kg-m, 5.5 lb-ft)
62) Install oil cooler (1) and ground cable (2).
Tightening torque
A/T oil cooler bolt (a): 60 N·m (6.0 kg-m, 43.5 lb-ft)
NOTE:
If metal particles are attached to the magnet, clean them
before installing.

7B-134 AUTOMATIC TRANSMISSION (4 A/T)
63) Install vehicle speed sensor (for speedometer) (1), shift
cable bracket (2) and connector clamp bracket (3).
Tightening torque
Vehicle speed sensor bolt
(a) : 5.5 N·m (0.55 kg-m, 4.0 lb-ft)
Shift cable bracket bolts
(b) : 13 N·m (1.3 kg-m, 9.5 lb-ft)
Connector clamp bracket bolt : 8 N·m (0.8 kg-m, 6.0 lb-ft)
64) Install A/T fluid filler tube (2) and level gauge (1).
Tightening torque
A/T fluid filler tube bolt (a) : 19.5 N·m (1.95 kg-m, 14.5 lb-ft)
65) Install output shaft speed sensor (1) and input shaft speed
sensor (2).
Apply grease to O-ring of each sensor.
Tightening torque
Output shaft speed sensor bolt
(a) : 8 N·m (0.8 kg-m, 6.0 lb-ft)
Input shaft speed sensor bolt
(b) : 8 N·m (0.8 kg-m, 6.0 Ib-ft)
Grease : 99000-25030
66) Install engine mounting LH bracket.
Tightening torque
Engine mounting LH bracket bolts
(a) : 55 N·m (5.5 kg-m, 40.0 lb-ft)

AUTOMATIC TRANSMISSION (4 A/T) 7B-135
67) Install breather sensor hose (1).
68) Install transmission range sensor (2).
Install it temporarily so that the adjustment can be done after
installing assembly back to the vehicle.
Tightening torque
Transmission range sensor bolt
(a) : 18 N·m (1.8 kg-m, 13.0 lb-ft)
69) Install torque converter (1) to input shaft.
Install torque converter, using care not to damage oil seal of
oil pump.
After installing torque converter, check to make sure that dis-
tance “a” is within specification.
Torque converter installing position
“a” : More than 19.9 mm (0.783 in.)
Check torque converter for smooth rotation.
Apply grease around cup at the center of torque converter.
“C” : Grease 99000-25010
CAUTION:
 Before installing converter, make sure that its pump
hub portion is free from nicks, burrs or damage which
may cause oil seal to leak.
 Be very careful not to drop converter on oil pump gear.
Damage in gear, should it occur, may cause a critical
trouble.
2. Flange nut
3. Torque converter housing
4. Cup

7B-136 AUTOMATIC TRANSMISSION (4 A/T)
TIGHTENING TORQUE SPECIFICATION
Fastening partTightening torque
Nm kg-m lb-ft
A/T fluid drain plug 23 2.3 16.5
Transmission rage sensor bolt 18 1.8 13.0
Output shaft speed sensor bolt 8 0.8 6.0
Input shaft speed sensor bolt 8 0.8 6.0
Dropping resistor bolts 20 2.0 14.5
Shift solenoid bolts 8 0.8 6.0
Transmission temperature sensor bolt 10 1.0 7.5
Transmission to engine bolts and nut 85 8.5 61.5
Drive plate to torque converter bolts 20 2.0 14.5
Starter motor bolts 23 2.3 16.5
Oil pump cover bolts 10 1.0 7.5
Valve body bolts 5.5 0.55 4.0
Final gear bolts 90 9.0 65.0
Counter drive gear installing bolts 5.5 0.55 4.0
Rear cover bolts 19 1.9 14.0
Control shift lever nuts 30 3.0 22.0
Detent spring bolt 11 1.1 8.0
Parking lock pawl sleeve bolt 19 1.9 14.0
Parking lock pawl bolts 11 1.1 8.0
Oil pump assembly bolts 12 1.2 9.0
Torque converter housing bolts 19 1.9 14.0
Wire-to-solenoid assembly bolt 8 0.8 6.0
Valve body to transmission case bolts 10 1.0 7.5
A/T oil pan bolts 7.5 0.75 5.5
A/T oil cooler bolt 60 6.0 43.5
Vehicle speed sensor bolt 5.5 0.55 4.0
Shift cable bracket bolt 13 1.3 9.5
Connector clamp bracket bolt 8 0.8 6.0
A/T fluid filler tube bolt 19.5 1.95 14.5
Engine mounting LH bracket bolts 55 5.5 40.0

AUTOMATIC TRANSMISSION (4 A/T) 7B-137
SPECIAL TOOL
09900-06108 09900-20606 09900-20701 09913-75510
Snap ring plier
(Closing type)Dial gauge Magnetic stand Bearing installer
09913-80112 09913-85210 9922-85811 09923-74510
Bearing installer Bearing installer Spring pin remover
(6 mm)Bearing remover
09924-74510 09925-37811-001 09925-88210 09926-26030
Installer handle Oil pressure gauge Bearing puller attachment Air installer No.1
09926-26040 09926-68310 09926-96010 09926-96020
Air installer No.2 Bearing installer Clutch spring compressor Clutch spring compressor

7B-138 AUTOMATIC TRANSMISSION (4 A/T)
09926-96030 09926-96040 09930-30102 09931-76030
Clutch spring compressor
No.7Clutch spring compressor
No.8Sliding shaft 16/14 pin DLC adapter
09931-76011 09941-64511 09944-68510 09951-16060
Tech 1A kit
See NOTE below.Bearing remover Bearing installer Bush remover
09952-06010 09952-06020 09926-26050
Dial gauge plate No.1 Dial gauge plate No.2 Mass storage cartridge Air installer No.3
09940-53111
Oil seal install tool