AC system FORD MUSTANG 2003 Owner's Guide

REFILL as necessary.
z Power steering pump
brackets loose or
misaligned. z
CHECK bolts, brackets
and bracket alignment.
TIGHTEN bolts to
specification. REPAIR
or INSTALL new
brackets as necessary.
REFER to Section 211 -
02 .
z Steering gear clunk
— occurs only
while cornering
over a bump (can
be temperature
sensitive) z
Steering gear. zINSPECT the steering
gear for loose mounting
bolts. TIGHTEN as
necessary. REFER to
Section 211 - 02 .
z Feedback (rattle,
chuckle or
knocking noise in
the steering gear)
— a condition
where roughness is
felt in the steering
wheel when the
vehicle is driven
over rough
surfaces z
Column
intermediate/flexible
shaft joints damaged or
worn. z
INSTALL a new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Loose, damaged or
worn tie- rod ends. z
TIGHTEN the nuts to
specification or
INSTALL new tie- rod
ends as necessary.
REFER to Section 211 -
02 .
z Steering gear
insulators or mounting
bolts loose or
damaged. z
TIGHTEN the bolts or
INSTALL new bolts as
necessary. REFER to
Section 211 - 02 .
z Steering column
intermediate shaft bolts
are loose. z
TIGHTEN the bolts to
specification. REFER to
Section 211 - 04 .
z Steering column
damaged or worn. z
REPAIR or INSTALL a
new steering column as
necessary. REFER to
Section 211 - 04 .
z Loose suspension
bushings, bolts or ball
joints. z
INSPECT the
suspension system.
TIGHTEN or INSTALL
new components as
necessary. REFER to
Section 204 - 01 .
z Feedback (nibble
at the steering
wheel) — a
condition where
slight rotational
movement is felt in
the steering wheel
when the vehicle is
driven over rough
or grooved z
Lateral runout in the
tire or wheel. z
GO to Pinpoint Test H . Klj . 34 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

end surface of the
power steering pump
rotor.
z Damaged or worn
power steering pump
rotor splines.
z A crack on the inner
surface of the power
steering pump cam.
z Interference between
the power steering
pump rotor and cam.
z Damaged or worn
power steering pump
rotor and pressure
plates. 02 .
z Power steering
pump swish noise z
Power steering fluid
flow into the bypass
valve of the pump
valve housing with fluid
temperature below 54°
C (130°F). z
Acceptable condition.
z Power steering
pump whine noise z
Aerated fluid. zPURGE the air from the
system. REFER to
Section 211 - 00 .
CHECK for a leak in the
system.
z Damaged power
steering pump cam. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Damaged valve cover
O-ring seal. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Power steering
pump clicking
(mechanical) noise z
Power steering pump
rotor slippers too long,
excessive rotor slipper-
to-slot clearance or
damaged or worn rotor
assembly. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Power steering
pump clatter noise z
Damaged corners on
the outside diameter or
the power steering
rotor or distorted rotor
slipper ring. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
Symptom Chart—
Suspension Noise/Vibration Condition
Possible Sources Action
z Squeak or grunt— noise
from the front suspension,
occurs more in cold
ambient temperatures.
More noticeable over
rough roads or when
turning z
Front stabilizer
bar insulators. z
Under these conditions,
the noise is acceptable.
CHECK TSBs. Klj . 36 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Gearshift lever
loose. z
TIGHTEN the bolts to
specification. REFER to
Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Gearshift linkage
rods worn or
damaged. z
CHECK the linkage
bushings for wear.
INSTALL new linkage
rods as necessary.
REFER to the
appropriate workshop
manual for the service
procedures.
z Transmission
rattling/clattering
noise— occurs in
neutral or in gear, at
idle z
Incorrect fluid level
or fluid quality. z
CHECK that the
transmission is filled to
the correct level and
with the specified fluid.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transmission
rattling/clattering
noise— noise at idle in
neutral z
Worn or rough
reverse idler gear. z
CHECK the reverse
idler gear. REPAIR as
necessary. REFER to
Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Rough running
engine, cylinder
misfire. z
CHECK the ignition
system. CARRY OUT a
cylinder power test.
REFER to Section 303 -
00 .
z Excessive backlash
in gears z
CHECK the gear
backlash. ADJUST as
necessary. REFER to
Section 205 - 02A for
Ford 7.5 rear axles or
Section 205 - 02B for
Ford 8.8 integral axles.
z Worn countershaft
gears. z
REPAIR as necessary.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transmission whine—
a mild whine at
extreme speeds or
high rpm z
Rotating
gears/geartrain. z
Acceptable noise.
z Transmission whine—
a high pitched whine,
also described as a
squeal z
Transmission gears
are worn (high
mileage vehicle). z
Result of normal gear
wear. REPAIR as
necessary. REFER to
Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions. Klj . 42 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

condition. It may not always be necessary to follow a pinpoint test to its conclusion. Carry out only the
steps necessary to correct the condition. Then, test the system for normal operation. Sometimes, it is
necessary to remove various vehicle components to gain access to the component requiring testing.
Reinstall all components after verifying system operation is normal.
PINPOINT TEST A: BRAKE VIBRATION/SHUDDER
Test Step Result / Action to Take
A1 ROAD TEST THE VEHICLE—
LIGHT BRAKING z
Check that the wheel and tires are correct for the vehicle.
Inspect the tires for abnormal wear patterns.
z Road test the vehicle. Warm the brakes by slowing the vehicle
a few times from 80– 32 km/h (50 to 20 mph) using light braking
applications. At highway speeds of 89–97 km/h (55- 60 mph),
apply the brake using a light pedal force.
z Is there a vibration/shudder felt in the steering wheel, seat
or brake pedal? Yes
GO to
A4 .
No
GO to A2 .
A2 ROAD TEST THE VEHICLE—
MODERATE TO HEAVY
BRAKING z
Road test the vehicle. At highway speeds of 89–97 km/h (55- 60
mph), apply the brake using a moderate to heavy pedal force.
z Is there a vibration/shudder? Yes
For vehicles with ABS,
GO to
A3 . For vehicles
with standard brakes,
GO to A4 .
No
Vehicle is OK. VERIFY
condition with customer.
TEST the vehicle for
normal operation. A3 NORMAL ACTUATION OF THE ABS SYSTEM DIAGNOSIS
z
During moderate to heavy braking, noise from the hydraulic
control unit (HCU) and pulsation in the brake pedal can be
observed. Pedal pulsation coupled with noise during heavy
braking or on loose gravel, bumps, wet or snowy surfaces is
acceptable and indicates correct functioning of the ABS
system. Pedal pulsation or steering wheel nibble, (frequency is
proportioned to the vehicle speed) indicates a concern with a
brake or suspension component.
z Is the vibration/shudder vehicle speed sensitive? Yes
GO to
A5 .
No
The brake system is
operating correctly. A4 APPLICATION OF THE PARKING BRAKE
z
NOTE: Begin at the front of the vehicle unless the vibration or
shudder has been isolated to the rear.
z This test is not applicable to vehicles with drum- in-hat type
parking brakes. For vehicles with drum- in-hat parking brakes,
proceed to the next test. For all other vehicles, apply the
parking brake to identify if the problem is in the front or rear
brake. At highway speeds of 89–97 km/h (55- 60 mph), lightly
apply the parking brake until the vehicle slows down. Release
the parking brake immediately after the test.
z Is there a vibration/shudder? Yes
GO to
A7 .
No
GO to A5 .
A5 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in this section.
z Are the wheel bearings OK? Yes
GO to
A6 . Klj . 48 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST B: ENGINE TICKING NOISE No
INSPECT the wheel
bearings. ADJUST or
REPAIR as necessary.
TEST the system for
normal operation.
A6 CHECK THE FRONT SUSPENSION
z
Check the front suspension for:
zBroken or loose bolts.
z Damaged springs.
z Worn or damaged upper and lower control arm
bushings.
z Loose or rough front bearings.
z Uneven tire wear.
z Are all the suspension components in satisfactory
condition? Yes
GO to
A7 .
No
REPAIR or INSTALL
new components as
necessary. TEST the
system for normal
operation. A7 RESURFACE THE FRONT BRAKE DISCS
z
CAUTION: Do not use a bench lathe to machine brake
discs.
z NOTE: Follow the manufacturer's instructions to machine the
brake discs. After machining, make sure the brake disc meets
the thickness specification.
z Refer to Brake Disc Machining in this section. Resurface the
front brake discs. Road test the vehicle.
z Is the vibration/shudder present? Yes
GO to
A8 .
No
Vehicle is OK. A8 CHECK THE REAR SUSPENSION
z
Check the rear suspension for:
zBroken or loose bolts.
z Damaged or worn springs or spring bushings.
z Worn or damaged upper and lower control arm
bushings.
z Worn or damaged trailing arms.
z Loose or rough rear bearings.
z Uneven tire wear.
z Are all the suspension components in satisfactory
condition? Yes
GO to
A9 .
No
REPAIR or INSTALL
new components as
necessary. TEST the
system for normal
operation. A9 RESURFACE THE REAR BRAKE DISC OR DRUM
z
CAUTION: Do not use a bench lathe to machine brake
discs.
z NOTE: Follow the manufacturers instructions to machine the
brake discs. After machining, make sure the brake disc meets
the thickness specification.
z Refer to Brake Disc Machining in this section. Resurface the
rear brake discs or drums. Road test the vehicle.
z Is the vibration/shudder present? Yes
CHECK the front
suspension for wear or
damage. RESURFACE
the front brake discs.
TEST the system for
normal operation.
No
Vehicle is OK.
Test Step Result / Action to Take
B1 CHECK FOR TICKING NOISE AT THE FUEL
RAIL z
Disconnect the first fuel line clip. Yes Klj . 49 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the ticking noise gone? CHECK for TSB for applicable vehicle.
REPAIR as necessary. TEST the system
for normal operation.
No
GO to
B2 .
B2 CHECK FOR TICKING NOISE AT THE FUEL
INJECTOR z
Using an EngineEAR, listen at the fuel
injectors by placing a probe on each injector.
To isolate the faulty injector, disconnect the
injector electrical connector and listen for the
noise.
z Is the fuel injector the source of the ticking
noise? Yes
INSTALL a new fuel injector. REFER to
Section 303
- 04A for 3.8L engines or
Section 303 - 04B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B3 .
B3 CHECK THE BELT TENSIONER FOR TICKING
NOISE z
Inspect the accessory drive. Check for the belt
tensioner bottoming at end of travel or not at
end of stroke.
z Using an EngineEAR, listen at the belt
tensioner.
z Is the belt tensioner the source of the
noise? Yes
INSTALL a new belt tensioner. TEST the
system for normal operation.
No
GO to
B4 .
B4 CHECK THE WATER PUMP FOR TICKING
NOISE z
Using an EngineEAR, listen at the water pump
for ticking noise.
z Is the water pump the source of the noise? Yes
INSTALL a new water pump. REFER to
Section 303
- 03A . TEST the system for
normal operation.
No
GO to B5 .
B5 CHECK FOR AN OBSTRUCTION OF THE
COOLING FAN z
Inspect the cooling fan for obstructions.
z Check the cooling fan and shroud for wear or
damage.
z Was there an obstruction or does the
cooling fan show signs of damage? Yes
REPAIR or INSTALL a new cooling fan.
REFER to
Section 303 - 03A . TEST the
system for normal operation.
No
GO to B6 .
B6 CHECK THE OIL PUMP FOR TICKING NOISE
z
Check the oil pump using EngineEARs and
probe at the oil filter adapter to verify the oil
pump as a source.
z Is the oil pump the source of the noise? Yes
INSTALL a new oil pump. REFER to
Section 303
- 01A for 3.8L engines or
Section 303 - 01B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B7 .
B7 CHECK VALVE LIFTERS OR LASH
ADJUSTERS FOR CORRECT OPERATION z
Check valve lifter/lash adjuster for correct
operation, using EngineEARs.
z Are the valve lifters/lash adjusters Yes
VERIFY customer concern. CONDUCT a
diagnosis of other suspect components. Klj . 50 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST C: ACCESSORY DRIVE BEARING HOOT
PINPOINT TEST D: POWER STEERING MOAN
PINPOINT TEST E: ENGINE DRIVEN COOLING FAN MOAN operating correctly?
No
INSTALL a new valve lifter/lash adjuster
(s). TEST the system for normal
operation.
Test Step Result / Action to Take
C1 CHECK THE IDLER AND TENSIONER
PULLEY BEARINGS z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Place an EngineEAR probe directly on the
pulley center post or bolt to verify which
bearing is making the noise.
z Key in OFF position.
z Is either bearing making the noise? Yes
INSTALL a new pulley/idler. CARRY OUT the
Vehicle Cold Soak Procedure and TEST the
system for normal operation.
No
CONDUCT a diagnosis on other suspect
accessory drive components.
Test Step Result / Action to Take
D1 CHECK THE POWER STEERING
SYSTEM z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Turn the steering wheel while the noise
is occurring and listen for changes in
sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
GO to
D2 .
No
CONDUCT a diagnosis on other suspect
accessory drive components. D2 VERIFY THE SOURCE
z
Key in START position.
z Place an EngineEAR probe near the
power steering pump/reservoir while the
noise is occurring. While an assistant
turns the steering wheel, listen for
changes in sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
VERIFY that the supply tube to the pump is
unobstructed. CHECK the fluid condition and
level. DRAIN the fluid and REFILL. CARRY
OUT the Vehicle Cold Soak Procedure and
TEST the system for normal operation. REFER
to Section 211
- 02 .
No
Normal system operation. Test Step Result / Action to Take
E1 CHECK THE ENGINE DRIVEN COOLING
FAN AFTER A COLD SOAK Klj . 51 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: DRUMMING NOISE z
Carry out the Vehicle Cold Soak Procedure
in this section.
z Key in START position.
z Assess the airflow.
z Raise the engine speed to 1500 rpm while
listening for the moan to increase in
proportion to the airflow.
z Key in OFF position.
z Does the moan increase in proportion to
the airflow? Yes
TEST the fan for normal operation. If the
fan tests normal, GO to
E2 . Otherwise,
REPAIR as necessary.
No
Normal system operation. E2 CHECK THE ENGINE DRIVEN COOLING
FAN AT NORMAL OPERATING TEMPERATURE z
Key in START position.
z Run the engine to normal operating
temperature while listening for the moan to
stop.
z Key in OFF position.
z Does the moan stop? Yes
Normal clutch operation.
No
INSTALL a new fan clutch. TEST the
system for normal operation.
Test Step Result / Action to Take
F1 CHECK THE EXHAUST SYSTEM
z
Key in START position.
z Increase the engine rpm until the noise is the loudest. Note
the engine rpm.
z Key in OFF position.
z Add approximately 9 kg (20 lb) of weight to the exhaust
system. First place the weight at the tail pipe and test, then
at the front pipe.
z Key in START position.
z Increase the engine rpm and listen for the drumming noise.
Note the engine rpm if the noise occurs.
z Key in OFF position.
z Using a vibration analyzer (VA), determine the amount of
vibration that occurs with the drumming noise.
z Is the noise/vibration reduced or eliminated, or does the
noise/vibration occur at a different rpm? Yes
CARRY OUT
Exhaust System Neutralizing in this
section. TEST the system
for normal operation.
No
GO to F2 .
F2 POWERTRAIN/DRIVETRAIN MOUNT NEUTRALIZING
z
Carry out Powertrain/Drivetrain Mount Neutralizing in this
section. Test the system for normal operation.
z Is the noise reduced or eliminated? Yes
Vehicle OK. TEST the
system for normal
operation.
No Klj . 52 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST G: ENGINE TICKING, KNOCKING OR CONTINUOUS
RATTLE
PINPOINT TEST H: FRONT SUSPENSION NOISE CONDUCT diagnosis of
other suspect components.
Test Step Result / Action to Take
G1 CHECK FOR NOISE AT THE VALVE COVERS
AND THE FRONT COVERS (OHC ENGINES) z
Carry out the Vehicle Cold Soak Procedure in
this section.
z Key in START position.
z NOTE: For a short- duration ticking noise,
multiple engine starts may be necessary.
z Using an EngineEAR, listen closely at the valve
covers and the front covers (OHC engines) by
placing the probe near the surface of the valve
cover and then on the surface front cover.
z Key in OFF position.
z Is the noise source apparent? Yes
REMOVE the appropriate cover and
INSPECT for loose, worn/broken
components. REPAIR as necessary.
TEST the system for normal operation.
No
GO to
G2 .
G2 CHECK FOR NOISE AT THE CYLINDER
BLOCK z
Key in START position.
z Using an EngineEAR, listen closely at the
cylinder block by placing a probe on or near
each freeze plug.
z Key in OFF position.
z Is the noise source apparent? Yes
REPAIR or INSTALL new components
as necessary.
No
GO to
G3 .
G3 CHECK FOR NOISE WHILE DISCONNECTING
EACH FUEL INJECTOR ELECTRICAL
CONNECTOR, ONE AT A TIME z
Key in START position.
z Disconnect each fuel injector electrical
connector, one at a time, to decrease piston
force and listen for the noise.
z Key in OFF position.
z Is the noise reduced or eliminated? Yes
INSTALL a new fuel injector. TEST the
system for normal operation.
No
INSPECT accessory drive system or the
transmission as a possible source.
Test Step Result / Action to Take
H1 ROAD TEST THE VEHICLE
z
Test drive the vehicle.
z NOTE: An assistant will be needed for this road test.
z During the road test, drive the vehicle over a rough road.
Using ChassisEARs, determine from which
area/component the noise is originating.
z Is there a squeak, creak or rattle noise? Yes
GO to
H2 .
No
The suspension system is
OK. CONDUCT a diagnosis
on other suspect systems. H2 INSPECT THE STEERING SYSTEM
Yes Klj . 53 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST I: REAR SUSPENSION NOISE z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the steering system for wear or damage. Carry out a
steering linkage test. Refer Section 211 - 00 .
z Inspect the tire wear pattern. Refer to Tire Wear Patterns
chart in this section.
z Are the steering components worn or damaged? REPAIR the steering
system. INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H3 .
H3 FRONT SHOCK ABSORBER/STRUT CHECK
z
Check the front shock absorbers/strut mounts for loose
bolts or nuts.
z Check the front shock absorbers/struts for wear or damage.
Carry out a "bounce test".
z Are the front shock absorbers/struts loose or
damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new front
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
H4 .
H4 CHECK THE FRONT SPRINGS
z
Check the front spring and front spring mounts/brackets for
wear or damage.
z Are the front springs or spring mounts/brackets worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H5 .
H5 CHECK THE CONTROL ARMS/RADIUS ARMS
z
Inspect the control arm bushings for wear or damage.
z Inspect for twisted or bent control/radius arm.
z Are the control/radius arms damaged or worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H6 .
H6 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step Result / Action to Take Klj . 54 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...