ISUZU KB P190 2007 Workshop Repair Manual

CAB 10-63


Important Operations - Removal
1. Front Sill Plate
• Pull out the 4 clip positions.
2. Rear Sill Plate • Pull out the 2 clip positions.

4. Fuel Filler Lid Opener Cover
• Pull out the 3 clip positions.


5. Fuel Filler Lid Opener Lever
• Remove the 2 opener fixing bolts and disconnect the
cable.


7. Fuel Filler Lid Cable Assembly
• Remove some fixing clips, turn the cable holder on the
side of the recess at 90 °counterclockwise and remove it
from the recess. Pull out the grommet in the direction o
f
the front of the vehicle and remove the cable assembly.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

10-64 CAB
INSTALLATION (REGULAR CAB RHD MODEL)

686R300017

Installation Steps
▲ 1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate





BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

CAB 10-65
INSTALLATION (EXTEND CAB RHD MODEL)

686R300019

Installation Steps
▲ 1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate





BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

10-66 CAB
INSTALLATION (CREW CAB RHD MODEL)

686R300013

Installation Steps
▲ 1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover


5. Center pillar lower trim cover
6. Rear sill plate
7. Front sill plate


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

CAB 10-67
INSTALLATION (REGULAR CAB LHD MODEL)





RTW 4A0LF000401

Installation Steps
▲ 1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate






BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

10-68 CAB
INSTALLATION (EXTEND CAB LHD MODEL)





RTW 4A0LF000501

Installation Steps
▲ 1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover
5. Front sill plate





BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

CAB 10-69
INSTALLATION (CREW CAB LHD MODEL)





RTW 4A0LF000601

Installation Steps
▲ 1. Fuel filler lid cable assembly
2. Rear wheel housing extension panel
3. Fuel filler lid opener lever
4. Fuel filler lid opener cover


5. Center pillar lower trim cover
6. Rear sill plate
7. Front sill plate




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

10-70 CAB


Important Operation - Installation
1. Fuel Filler Lid Cable Assembly • Install the cable holder of the cable assembly to the
recess and push the grommet in to the back panel. Fix
the clips to the appointed places.
Note:
To install, follow the removal steps in the reverse order,
noting the following points.
•
••
•
Do not make an extreme curve on the cable.
•
••
•
Install the cable from inside the cab.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

CAB 10-71
QUARTER GLASS (EXTEND CAB)
REMOVAL AND INSTALLATION




RTW 5A0MF000501

Removal Steps
▲ 1. Body side rear trim covers
2. Hinge/Fastener
3. Quarter glass
4. W eather strip

Installation Steps
▲
4. W eather strip
3. Quarter glass
2. Hinge/Fastener
1. Body side rear trim covers







Important Operation - Removal
1. Body Side Rear Trim Covers • Refer to Interior Trim Panels in this section.

Important Operation – Installation
4. Weather Strip • Install the weather strip by aligning the corners with a
white mark to the upper corners on the body panel.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

10-72 CAB
FRONT SEAT
REMOVAL AND INSTALLATION





RTW 3A0MF000301

Removal Steps
▲ 1. Front cover
2. Rear cover
3. Bolt
▲ 4. Seat assembly
▲ 5. Buckle side seat belt/center seat belt
6. Seat adjuster

Installation Steps
6. Seat adjuster
▲ 5. Buckle side seat belt/center seat belt
4. Seat assembly
▲ 3. Bolt
2. Rear cover
1. Front cover




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007