ISUZU KB P190 2007 Workshop Repair Manual
Manufacturer: ISUZU, Model Year: 2007, Model line: KB P190, Model: ISUZU KB P190 2007Pages: 6020, PDF Size: 70.23 MB
Page 5861 of 6020

11A-10 IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6)
Scan Tool Data List
The Immobilizer Scan Tool Data List contains all
immobilizer related parameters that are available on
the scan tool. Use the Immobilizer Scan Tool Data List
only after the following is determined:
• The Immobilizer Controls - Diagnostic System Check is completed. • On-board diagnostics are functioning properly.
A scan tool that displays faulty data should not be used.
Use of a faulty scan tool can result in misdiagnosis and
unnecessary parts replacement.
Only the parameters listed below are referenced in this
service manual for use in diagnosis.
Scan Tool Data Definitions
This information will assist in immobilizer problems.
Always perform the Diagnostic System Check -
Immobilizer Controls first. The Diagnostic System
Check will confirm proper system operation.
Ignition Status
This parameter displays the state of the ignition switch
input to the ICU. On indicates the ignition switch is
turned ON position.
Transponder Key
This parameter displays the state of the transponder
key in the steering lock. Transponder Key 1 to 5
indicates a correctly programmed transponder key is
used. The number 1 to 5 indicates which transponder
key is used. Invalid indicates an incorrect key is in
used. Not Programmed Key indicates a non-
programmed new transponder key is used. No
Transponder Key indicates ICU does not recognize a
transponder key. Transponder Status
This parameter displays the state of the transponder
key in the steering lock. Correct Transponder-Key
indicates a correctly programmed transponder key is
used. Wrong Transponder-Key indicates an incorrect
key is in used. New Transponder-Key indicates a non-
programmed new transponder key is used. No
Transponder Detected indicates ICU does not
recognize a transponder key.
Transponder-Key 1 to 5 Status
This parameter displays the state of number of
programmed transponder key(s). Programmed
indicates transponder key 1 to 5 is correctly
programmed. The number 1 to 5 indicates programmed
order.
Security Code Programmed
This parameter displays the state of the security code
programming. Yes indicates a security code is correctly
programmed. No indicates a security code is not
programmed.
Scan Tool Parameter Units DisplayedTypical Data Value
Operating Conditions: Ignition switch ON/ Two transponder keys programmed
Ignition Status On/ OffOn
Transponder Key Transponder Key 1 to 5/ Invalid/ Not
Programmed Key/ No Transponder Key Transponder Key 1 or 2
Transponder Status Correct Transponder-Key/ Wrong
Transponder-Key/ New Transponder- Key/ No Transponder Detected Correct Transponder-Key
Transponder-Key 1 Status Programmed/ Not Programmed Programmed
Transponder-Key 2 Status Programmed/ Not Programmed Programmed
Transponder-Key 3 Status Programmed/ Not Programmed Not Programmed
Transponder-Key 4 Status Programmed/ Not Programmed Not Programmed
Transponder-Key 5 Status Programmed/ Not Programmed Not Programmed
Security Code Programmed Yes/ NoYes
Security Wait Time Inactive/ Time (hour: minute: second) Inactive
While Security Lock Inactive/ Active Inactive
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5862 of 6020

IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6) 11A-11
Security Wait Time
This parameter displays the security wait time length in
the ICU. Inactive indicates not in security wait time.
Time indicates under security wait time. This wait time
stage will prevent any further attempts to enter the
security code until the wait time has elapsed. The wait
time will increase each time an incorrect security code
is entered. Note that this parameter is not count
downed. It keeps displaying the same time until that
wait time has elapsed. The ignition switch must be kept
at ON position during the wait time period.
While Security Lock
This parameter displays the state of the security wait
time. Inactive indicates not in security wait time. Active
indicates under security wait time.
BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007
Page 5863 of 6020

11A-12 IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6)
Scan Tool Does Not Power Up
Circuit Description
The data link connector (DLC) is a standardized 16-
cavity connector. Connector design and location is
dictated by an industry wide standard, and is required
to provide the following:
• Scan tool power battery positive voltage at terminal 16.
• Scan tool power ground at terminal 4. • Common signal ground at terminal 5.
The scan tool will power up with the ignition OFF. Some
modules however, will not communicate unless the
ignition is ON.
Schematic Reference: Immobilizer Controls
Schematics
Connector End View Reference: ICU Connector End
View
Circuit/ System Testing Scan Tool Does Not Power Up
Step Action Value(s)Yes No
1 Important
: Make sure the scan tool works properly
on another vehicle before using this chart.
1. Turn OFF the ignition.
2. Inspect the Meter (+B) (10A) fuse in the cabin fuse block.
Is the Meter (+B) (10A) fuse open? —
Go to Step 2 Go to Step 3
2 Replace the Meter (+B) (10A) fuse. If the fuse
continues to open, repair the short to ground on
one of the circuits that is fed by the Meter (+B)
(10A) fuse or replace the shorted attached
component.
Did you complete the repair? —
Go to Step 7
—
31. Check each circuit at the data link connector
(DLC) (B-58) for a backed out, spread or
missing terminal.
2. Repair the terminal as necessary.
Did you find and complete the repair? —
Go to Step 7 Go to Step 4
4 Connect a test lamp between the +B circuit (pin 16
of B-58) at the DLC and a known good ground.
Does the test lamp illuminate? —
Go to Step 6 Go to Step 5
5 Repair the open in the battery voltage circuit to the
DLC.
Did you complete the repair? —
Go to Step 7
—
61. Test each ground circuit at the DLC (pins 4
and 5 of B-58) for an open circuit or high
resistance.
2. Repair the circuit(s), clean or tighten ground as necessary.
Did you find and correct the condition? —
Go to Step 7 Go to Intermittent
Conditions
7 1. Connect the scan tool to the DLC.
2. Attempt to turn ON the scan tool.
Does the scan tool ON? —
System OK Go to Step 1
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5864 of 6020

IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6) 11A-13
Scan Tool Does Not Communicate with CAN Device
Circuit Description
The engine control module (ECM), transmission control
module (TCM) (AISIN A/T only) and ICU all
communicate with the scan tool over the controller area
network (CAN) link. The ECM, TCM, ICU and the data
recording module (DRM) communicate with each other
over the same CAN link. (4JK1/ 4JJ1)
The ECM, TCM, powertrain interface module (PIM) and
ICU all communicate with the scan tool over the CAN
link. (HFV6)
Diagnostic Aids
The following conditions will cause a loss of CAN serial
data communication between the ECM, TCM and PIM
or between the scan tool and any control module: • A CAN serial data circuit open
• A CAN serial data circuit shorted to ground
• A CAN serial data circuit shorted to voltage
• An internal condition within a module or connector on the CAN serial data circuit, that causes a short
to voltage or ground to the CAN serial data circuit
Schematic Reference: Immobilizer Controls
Schematics
Connector End View Reference: ICU Connector End
View
Circuit/ System Testing Scan Tool Does Not Communicate with CAN Device (4JK1/ 4JJ1)
Step Action Value(s)Yes No
1 Did you perform the Diagnostic System Check -
Immobilizer Controls? —
Go to Step 2 Go to Diagnostic
System Check - Immobilizer
Controls
2 Important
: Make sure the CANdi module is not
malfunctioning. When functioning properly, the
CANdi module LED will be flashing. In the event of
a problem, the LED will be continually illuminated
or not illuminated.
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Attempt to establish communication with the listed control modules.
• Immobilizer Control Unit (ICU)
• Engine control module (ECM)
• Transmission control module (TCM) (AISIN A/T only)
Does the scan tool communicate with any of the
listed control modules? —
Go to Step 3 Go to Step 7
3 Does the scan tool communicate with the ECM?
—
Go to Step 4 Go to Diagnostic
System Check -
Engine Controls
4 Notice:
If no AISIN automatic transmission is
installed, skip to Step 5.
Does the scan tool communicate with the TCM? —
Go to Step 5 Go to Diagnostic
System Check - Transmission
Controls
5 Does the scan tool communicate with the ICU?
—Go to Step 6 Go to Lost
Communication with The Immobilizer
Control Unit (ICU)
BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007
Page 5865 of 6020

11A-14 IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6)
6Test the CAN Low and High serial data circuit for an
intermittently short to ground, intermittently short to
voltage or short circuit each other. Then, test the
CAN Low and High serial data circuit for an
intermittently open (based on which control module
did not communicate) at the connection in the
circuit.
Did you find and correct the condition? —
Go to Step 17 System OK
7 1. Inspect for an intermittent, for poor
connections and for corrosion at the data link
connector (DLC) (pins 6 and 14 of B-58)
2. Repair the connection(s) as necessary.
Did you find and correct the condition? —
Go to Step 17 Go to Step 8
8 Notice:
If no data recording module (DRM) is
installed, skip to Step 9.
1. Turn OFF the ignition.
2. Disconnect the DRM C-139 harness connector.
3. Turn ON the ignition, with the engine OFF.
4. Attempt to communicate with the ECM, TCM and ICU.
Does the scan tool communicate with the ECM,
TCM and ICU? —
Go to Step 13 Go to Step 9
9 1. Turn OFF the ignition.
2. Reconnect the DRM C-139 harness connector if disconnected.
3. Disconnect the ECM J1 (E-90) and J2 (C-58) harness connectors.
4. Turn ON the ignition, with the engine OFF.
5. Attempt to communicate with the TCM and ICU.
Does the scan tool communicate with the TCM and
ICU? —
Go to Step 14 Go to Step 10
10 Notice:
If no AISIN automatic transmission is
installed, skip to Step 11.
1. Turn OFF the ignition.
2. Reconnect the ECM J1 (E-90) and J2 (C-58) harness connectors.
3. Disconnect the TCM C-94 and C-95 harness connectors.
4. Turn ON the ignition, with the engine OFF.
5. Attempt to communicate with the ECM and ICU.
Does the scan tool communicate with the ECM and
ICU? —
Go to Step 15 Go to Step 11
Step
Action Value(s)Yes No
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5866 of 6020

IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6) 11A-15
Circuit/ System Testing Scan Tool Does Not Communicate with CAN Device (HFV6)
111. Turn OFF the ignition.
2. Reconnect the ECM J1 (E-90) and J2 (C-58) harness connectors if disconnected.
3. Reconnect the TCM C-94 and C-95 harness connectors if disconnected.
4. Disconnect the ICU B-109 harness connector.
5. Turn ON the ignition, with the engine OFF.
6. Attempt to communicate with the ECM and TCM.
Does the scan tool communicate with the ECM and
TCM? —
Go to Step 16 Go to Step 12
12 Repair the open circuit, short to ground, short to
voltage or short circuit each other on the CAN Low
or High serial data circuit between the DLC and
ECM, TCM, ICU or DRM.
Did you complete the repair? —
Go to Step 17
—
13Replace the DRM. Refer to DRM Replacement.
Did you complete the replacement? —
Go to Step 17—
14Important
: Replacement ECM must be
programmed and learned.
Replace the ECM. Refer to ECM Replacement.
Did you complete the replacement? —
Go to Step 17
—
15Important
: Replacement TCM must be
programmed.
Replace the TCM. Refer to TCM Replacement.
Did you complete the replacement? —
Go to Step 17
—
16Important
: Replacement ICU must be
programmed.
Replace the ICU. Refer to ICU Replacement.
Did you complete the replacement? —
Go to Step 17
—
17Attempt to establish communication with the ECM,
TCM and ICU.
Does the scan tool communicate with the ECM,
TCM and ICU? —
System OK Go to Step 2
Step Action Value(s)Yes No
1 Did you perform the Diagnostic System Check -
Immobilizer Controls? —
Go to Step 2 Go to Diagnostic
System Check - Immobilizer Controls
Step
Action Value(s)Yes No
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5867 of 6020

11A-16 IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6)
2Important:
Make sure the CANdi module is not
malfunctioning. When functioning properly, the
CANdi module LED will be flashing. In the event of
a problem, the LED will be continually illuminated
or not illuminated.
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Attempt to establish communication with the listed control modules.
• Immobilizer Control Unit (ICU)
• Engine control module (ECM)
• Transmission control module (TCM)
• Powertrain Interface module (PIM)
Does the scan tool communicate with any of the
listed control modules? —
Go to Step 3 Go to Step 8
3 Does the scan tool communicate with the PIM?
—
Go to Step 4 Go to Diagnostic
System Check -
Powertrain Interface
Module
4 Does the scan tool communicate with the ECM?
—Go to Step 5 Go to Diagnostic
System Check -
Engine Controls
5 Notice:
If no automatic transmission is installed,
skip to Step 6.
Does the scan tool communicate with the TCM? —
Go to Step 6 Go to Diagnostic
System Check - Transmission Controls
6 Does the scan tool communicate with the ICU?
—Go to Step 7 Go to Lost
Communication with The Immobilizer
Control Unit (ICU)
7 Test the CAN Low and High serial data circuit for an
intermittently short to ground, intermittently short to
voltage or short circuit each other. Then, test the
CAN Low and High serial data circuit for an
intermittently open (based on which control module
did not communicate) at the connection in the
circuit.
Did you find and correct the condition? —
Go to Step 20 System OK
8 1. Inspect for an intermittent, for poor
connections and for corrosion at the data link
connector (DLC) (pins 6 and 14 of B-58).
2. Repair the connection(s) as necessary.
Did you find and correct the condition? —
Go to Step 20 Go to Step 9
9 1. Turn OFF the ignition.
2. Disconnect the ECM C-56 and E-60 harness connectors.
3. Turn ON the ignition, with the engine OFF.
4. Attempt to communicate with the TCM, PIM and ICU.
Does the scan tool communicate with the TCM,
PIM and ICU? —
Go to Step 16 Go to Step 10
Step
Action Value(s)Yes No
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5868 of 6020

IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6) 11A-17
10Notice:
If no automatic transmission is installed,
skip to Step 11.
1. Turn OFF the ignition.
2. Reconnect the ECM C-56 and E-90 harness connectors.
3. Disconnect the TCM C-96 harness connector.
4. Turn ON the ignition, with the engine OFF.
5. Attempt to communicate with the PIM and ICU.
Does the scan tool communicate with the PIM and
ICU? —
Go to Step 13 Go to Step 11
11 1. Turn OFF the ignition.
2. Reconnect the ECM C-56 and E-90 harness connectors if disconnected.
3. Reconnect the TCM C-96 harness connector if disconnected.
4. Disconnect the PIM B-96 and B-97 harness connectors.
5. Turn ON the ignition, with the engine OFF.
6. Attempt to communicate with the ICU.
Does the scan tool communicate with the ICU? —
Go to Step 14 Go to Step 12
12 1. Turn OFF the ignition.
2. Reconnect the PIM B-96 and B-97 harness connectors.
3. Disconnect the ICU B-109 harness connector.
4. Turn ON the ignition, with the engine OFF.
5. Attempt to communicate with the ECM, TCM and PIM.
Does the scan tool communicate with the ECM,
TCM and PIM? —
Go to Step 19 Go to Step 15
13 1. Test the CAN Low and High circuits between
the ECM (pins 23 and 55 of C-56) and the
TCM (pins 6 and 7 of C-96) for the following
conditions:
• A short to ground
• A short to battery or ignition voltage
• A short circuit each other
2. Repair the circuit(s) as necessary.
Did you find and correct the condition? —
Go to Step 20 Go to Step 17
14 1. Test the CAN Low and High circuits between
the PIM (pins 7 and 9 of B-97) and the TCM
(pins 37 and 38 of C-96) or ECM (pins 23 and
55 of C-56) for the following conditions:
• A short to ground
• A short to battery or ignition voltage
• A short circuit each other
2. Repair the circuit(s) as necessary.
Did you find and correct the condition? —
Go to Step 20 Go to Step 18
Step
Action Value(s)Yes No
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5869 of 6020

11A-18 IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6)
15Repair the open circuit, short to ground, short to
voltage or short circuit each other on the CAN Low
or High circuits between the DLC and PIM or ICU.
Did you complete the repair? —
Go to Step 20
—
16Important:
Replacement ECM must be
programmed and learned.
Replace the ECM. Refer to ECM Replacement.
Did you complete the replacement? —
Go to Step 20
—
17Important:
Replacement TCM must be
programmed.
Replace the TCM. Refer to ECM Replacement.
Did you complete the replacement? —
Go to Step 20
—
18Important:
Replacement PIM must be
programmed.
Replace the PIM. Refer to PIM Replacement.
Did you complete the replacement? —
Go to Step 20
—
19Important:
Replacement ICU must be
programmed.
Replace the ICU. Refer to ICU Replacement.
Did you complete the replacement? —
Go to Step 20
—
20Attempt to establish communication with the ICU,
ECM, TCM and PIM.
Does the scan tool communicate with the ICU,
ECM, TCM and PIM? —
System OK Go to Step 2
Step
Action Value(s)Yes No
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 5870 of 6020

IMMOBILIZER CONTROL SYSTEM (4JK1/4JJ1/HFV6) 11A-19
Lost Communication with The Immobilizer Control Unit (ICU)
Circuit Description
The engine control module (ECM), transmission control
module (TCM) (AISIN A/T only) and ICU all
communicate with the scan tool over the controller area
network (CAN) link. The ECM, TCM, ICU and the data
recording module (DRM) communicate with each other
over the same CAN link. (4JK1/ 4JJ1) The ECM, TCM, powertrain interface module (PIM) and
ICU all communicate with the scan tool over the CAN
link. (HFV6)
Schematic Reference: Immobilizer Controls
Schematics
Connector End View Reference: ICU Connector End
View
Circuit/ System Testing Lost Communication with The Immobilizer Control Unit (ICU)
Step Action Value(s)Yes No
1 Did you perform the Diagnostic System Check -
Immobilizer Controls? —
Go to Step 2 Go to Diagnostic
System Check - Immobilizer Controls
2 Attempt to establish communication with the ICU.
Does the scan tool communicate with the ICU? —
Go to Intermittent
Conditions Go to Step 3
3 1. Turn OFF the ignition.
2. Disconnect the scan tool from the data link connector (DLC) if connected.
3. Measure the resistance across the CAN Low and High circuits by probing the DLC (pins 6
and 14 of B-58).
Is the resistance within the specified value (parallel
resistance of the 120 Ω resistor in the ECM and the
120 Ω resistor in the ICU should be 60 Ω)? 50 to 70
Ω
Go to Step 5 Go to Step 4
4 1. Test the CAN Low and High circuits between
the ICU (pins 5 and 6 of B-109) and the data
link connector (DLC) (pins 6 and 14 of B-58)
for an open circuit or high resistance.
2. Repair the circuit(s) as necessary.
Did you find and correct the condition? —
Go to Step 11 Go to Step 9
5 1. Turn OFF the ignition.
2. Disconnect the ICU harness connector.
3. Connect a test lamp between the battery voltage feed circuit (pin 1 of B-109) and a
known good ground.
Does the test lamp illuminate? —
Go to Step 6 Go to Step 7
6 Connect a test lamp across the battery voltage feed
circuit and the ground circuit (pins 1 and 3 of B-
109)
Does the test lamp illuminate? —
Go to Step 9 Go to Step 8
7 Repair the open circuit or high resistance between
the Meter (+B) (10A) fuse and the ICU (pin 1 of B-
109).
Did you complete the repair? —
Go to Step 11
—
8Repair the open circuit or high resistance between
the ICU (pin 3 of B-109) and ground terminal.
Did you complete the repair? —
Go to Step 11
—
BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007