CHERY TIGGO 2009 Service Workshop Manual

Downloaded from www.Manualslib.com manuals search engine Installation Notes:
•Use special tool CH-20010 (1), to install the camshaft holder to hold the camshafts in place.
NOTE :
The camshaft holder will prevent the camshafts from
rotating in either direction.
• Use special tool CH-20002 (1), to install the camshaft seal.
• Install the intake and exhaust camshaft bearing
caps in the proper order.
• Slowly tighten bolts to the specified torque.
• Follow the torque sequence as shown.
ON-VEHICLE SERVICE
BESM020016
LTSM020215
BESM020036
02
02–22Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Cylinder Head
Removal & Installation
NOTE :
Replacement cylinder head comes complete with valves, seals, springs, retainers, keepers, and camshafts.1. Remove engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
2. Remove the cylinder head cover (See Cylinder Head Cover Removal & Installation in Section 02 Engine).
3. Remove the camshafts (See Camshaft Removal & Installation in Section 02 Engine).
4. Remove intake manifold (See Intake Manifold Removal & Installation in Section 02 Engine).
5. Remove exhaust manifold (See Exhaust Manifold Removal & Installation in Section 02 Engine).
6. Remove water pipe and thermostat assembly.
1 - Rocker Arms
2 - Hydraulic Tappets
3 - Valve Keepers
4 - Valve Spring Upper Retainers5 - Valve Springs
6 - Valve Oil Seals
7 - Valve Spring Lower Retainers
8 - Valves
ON-VEHICLE SERVICE
LTSM020167
02–23Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 7. Remove the cylinder head bolts in the ordershown.
8. Remove cylinder head gasket.
9. Installation is in the reverse order of removal.
Installation Notes:
• Ensure cylinder head bolt holes in the block are clean, dry (free of residual oil or coolant), and threads are not
damaged.
• The cylinder head bolts should not be reused. The new bolts should be examined before use. If the bolts are
stretched, the bolts should be replaced.
• Position the new cylinder head gasket on the engine block with the part number facing up. Ensure gasket is
seated over the locating dowels in the block.
• Before installing the bolts, the threads should be lightly coated with engine oil.
ON-VEHICLE SERVICE
BESM020065
02
02–24Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine •Install the cylinder head bolts in the order shown.
• Torque the cylinder head bolts in the following three
step sequence:
1st Step: Tighten the bolt to 40±5N·m
2nd Step: Tighten the bolt an additional 90 ±
5°
3rd Step: Tighten the bolt an additional 90 ± 5°
Front Crankshaft Oil Seal
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
• CH-20007 - Front Crankshaft Seal Installer
• CH-20008 - Front Crankshaft Seal Guide
• CH-20019 - Crankshaft Belt Pulley Fixture
1. Remove the accessory drive belt (See Accessory Drive Belt Removal & Installation in Section 02 Engine).
2. Remove the crankshaft vibration damper bolts (1). (Tighten: Crankshaft vibration damper bolts to
25 N·m)
3. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
ON-VEHICLE SERVICE
LTSM020236
BESM020055
02
02–25Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4. Remove the crankshaft timing belt pulley bolt (2)from the crankshaft.
(Tighten: Crankshaft timing belt pulley bolt to
130 N·m and an additional 65°)
5. Remove the key-way from the crankshaft.
6. Use an appropriate tool and remove the front crankshaft oil seal (1).
CAUTION:
Be careful not to damage the front cover seal
surface while removing the seal.
7. Installation is in the reverse order of removal.
Installation Notes:
• Lubricate the new front seal with engine oil prior to assembly.
• Use the front crankshaft seal installer CH-20008 (1), to install the new seal.
ON-VEHICLE SERVICE
LTSM020199
LTSM020216
02–26Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Rear Crankshaft Oil Seal
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
•CH-20005 - Rear Crankshaft Oil Seal Installer
• CH-20006 - Rear Crankshaft Oil Seal Guide
• CH-20043 - Flywheel Fixture
1. Remove the transaxle assembly (See Transaxle Assembly Removal & Installation in Section 08 Transaxle & Transfer Case).
2. Using special tool CH-20043 (1), hold the flywheel.
3. Remove the clutch pressure plate retaining bolts (1) and then remove the clutch pressure plate.
(Tighten: Clutch pressure plate bolts to 25 N·m)
4. Remove the flywheel bolts (1) and then remove the flywheel.
(Tighten: Flywheel bolts to 75 N·m)
ON-VEHICLE SERVICE
LTSM080145
BESM080046
BESM020058
02
02–27Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 5. Remove the rear oil seal using a suitable tool.
6. Installation is in the reverse order of removal.
Installation Notes:
• When installing seal, lubricate seal guide with clean
engine oil.
• Position the seal over the rear crankshaft seal
guide.
• Use special tool CH-20005 (2) CH-20006 (1), to
install the rear crankshaft oil seal.
• Ensure that the lip of the seal is facing toward the
crankcase during installation.
ON-VEHICLE SERVICE
LTSM020217
02–28Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Engine Mounts
Removal & Installation - Left Mount
NOTE :
The following special tools are required to perform the repair procedure:
•Engine Hoist
1. Disconnect the negative battery cable.
2. Support the engine with the engine hoist.
3. Remove the air cleaner housing (See Air Cleaner Housing Removal & Installation in Section 02
Engine).
4. Remove the air cleaner housing base tray.
5. Remove the engine left mount retaining bolts (2) and remove the engine left mount bracket bolts (1).
(Tighten: Engine left mount bolts to 70 N·m)
6. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020156
02
02–29Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Removal & Installation - Right Mount
NOTE :
The following special tools are required to perform the repair procedure:
•Engine Hoist
1. Disconnect the negative battery cable.
2. Support the engine with the engine hoist.
3. Remove the engine right mount retaining bolts (2) and remove the engine right mount bracket bolts
(1).
(Tighten: Engine right mount bolts to 70 N·m)
4. Installation is in the reverse order of removal.
Removal & Installation - Front Mount
NOTE :
The following special tools are required to perform the
repair procedure:
• Engine Hoist
1. Disconnect the negative battery cable.
2. Support the engine with the engine hoist.
3. Remove the bolts (1) securing the front engine mount.
(Tighten: Engine front mount bolts to 60 N·m)
4. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020155
BESM080035
02–30Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Removal & Installation - Rear Mount
NOTE :
The following special tools are required to perform the
repair procedure:
•Engine Hoist
1. Disconnect the negative battery cable.
2. Support the engine with the engine hoist.
3. Remove the engine rear mount retaining bolts (2) and remove the engine rear mount bracket bolts
(1).
(Tighten: Engine rear mount bolts to 60 N·m)
4. Installation is in the reverse order of removal.
Engine Assembly
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
• CH-20001 - Right Engine Mount Bolt Remover
• Engine Hoist
NOTE :
The engine is removed with the transaxle as an assembly. 1. Remove the vehicle hood.
2. Remove the negative battery cable from the engine.
3. Remove the engine cover.
4. Remove the battery, battery hold downs, and battery tray (See Battery Removal & Installation in Section 05 Starting & Charging).
5. Discharge air conditioning system (See A/C System Evacuation and Recharge in Section 13 Heating & Air Con- ditioning).
6. Drain the cooling system (See Cooling System Draining and Filling in Section 06 Cooling).
WARNING!
Always allow the engine to cool before opening the cooling system. Do not loosen the coolant pressure relief
cap when the engine is operating or the cooling system is hot. The cooling system is under pressure; steam and
hot liquid can come out forcefully when the cap is loosened slightly. Failure to follow these instructions may
result in serious personal injury.
ON-VEHICLE SERVICE
LTSM020188
02
02–31Chery Automobile Co., Ltd.