battery ISUZU TROOPER 1995 Workshop Manual

Q)
DRIVEABILITV AND EMISSIONS 6E2-67
DIAGNOSTIC TROUBLE CODE (DTC) 21 B
THROTTLE POSITION (TP) SENSOR CIRCUIT
(SIGNAL
VOLTAGE LOW)
• THROTTLE CLOSED.
DOES "SCAN TOOL" DISPLAY THROTTLE POSITION (TP) SENSOR 0.2V· (200mV) OR BELOW?
~ $
• DISCONNECT TP SENSOR. • IF TP SENSOR
SIGNAL VOLTAGE INDICATES "HIGH" JUMPER 5V REFERENCE AND TP SENSOR SIGNAL VOLTAGE
ABOVE 4.0 VOLTS, REFER TO DIAGNOSTIC CKT TOGETHER. TROUBLE CODE 21A. "SCAN TOOL" SHOULD DISPLAY TP SENSOR OVER • DIAGNOSTIC TROUBLE CODE 21 IS INTERMITTENT.
4.0V IF NO ADDITIONAL DIAGNOSTIC TROUBLE CODES
DOES IT? WERE STORED, REFER TO "DIAGNOSTIC AIDS" ON FACING~.
LfJ ~
• PROBE TP SENSOR SIGNAL CKT WITH A TEST @ • REFER To FACING EAe'E'1oR J LIGHT CONNECTED TO BATTERY POSITIVE SPECIFIC INSTRUCTIONS.
VOLTAGE.
"SCAN TOOL" SHOULD DISPLAY TP SENSOR
OVER 4.0V
DOES
IT?
~ $
5V REFERENCE CKT OPEN OR SHORTED TO GROUND TP SENSOR SIGNAL CKT OPEN OR
OR SHORTED TO GROUND, OR SHORTED FAULTY CONNECTION
TO SENSOR GROUND CIRCUIT OR
OR FAULTY ENGINE CONTROL MODULE. FAULTY ENGINE CONTROL MODULE CONNECTION OR FAULTY ENGINE CONTROL MODULE.
CLEAR
DIAGNOSTIC TROUBLE CODES AND CONFIRM "CLOSED LOOP" OPERATION AND NORMAL "CHECK ENGINE" MALFUNCTION
INDICATOR LAMP OPERATION.

DRIVEABILITV AND EMISSIONS 6E2-75
DIAGNOSTIC TROUBLE CODE (DTC) 32
EXHAUST GAS RECIRCULATION(EGR) CIRCUIT
• FIRMLY GRASP TOP OF EXHAUST GAS RECIRCULATION (EGR} VALVE AND CHECK FOR LOOSENESS BY TRYING TO
ROTATE VALVE IN BOTH DIRECTIONS.
IS LOOSENESS FELT?
l
$
-[$J
• PLACE TRANSMISSION IN "PARK" OR "NEUTRAL". REPLACE EGR VALVE I • RUN WARM ENGINE AT IDLE. ASSEMBLY
• ENGINE TEMPERATURE MUST BE ABOVE 60'C (120'F). • DISCONNECT VACUUM HOSE TO EGR VALVE. • APPLY 10"1NCHES OF VACUUM TO EGR VALVE. • ENGINE SHOULD RUN ROUGH AND/OR STALL.
DOES IT?
I
$ $
•
CONNECT VACUUM GAGE TO EGR SIDE OF VACUUM • REMOVE EGR VALVE AND CLEAN SWITCHING VALVE (VSV). ASSEMBLY.
• INCREASE ENGINE SPEED ABOVE 2000 REVOLUTION • REPLACE
VALVE IF NECESSARY. PER MINUTE.
SHOULD HAVE AT LEAST 10 INCHES OF VACUUM. DOES IT!
I
$ $
• DATA LINK CONNECTOR GROUNDED . @ • INSTALL VACUUM GAUGE TO THE
• ENGINE IDLING CHECK VACUUM SOURCE VACUUM HOSE AT THE EGR VALVE. BEFORE EGR MODULATOR. • INCREASE ENGINE SPEED TO ABOVE 2000 . SHOULD HAVE AT LEAST 10" OF VACUUM. AT LEAST 10" OF VACUUM. DOES IT? DOES IT!
I
I
$ $ $ ~
REFER TO @ • IGNITION "ON", ENGINE "OFF". EGR SYSTEM • INSPECT BACK PRESSURE
"DIAGNOSTIC • TEST LIGHT TO GROUND. WORKING PROPERLY. TUBE "S" FOR DAMAGE OR AIDS" ON
.
• BACKPROBE VOLTAGE SOURCE NO
TROUBLE FOUND. RESTRICTION. FACING'¢{ TO EGR VALVE VSV
SOLENOID. •
INSPECT VACUUM HOSE
TEST LIGHT SHOULD BE "ON". FROM THE EGR
IS IT? MODULATOR TO THE EGR
I VALVE FOR DAMAGE OR
$ $
RESTRICTION. IF OK, REPLACE EGR MODULATOR.
@ • REPEAT ABOVE TEST WITH TEST
OPEN IN I LIGHT TO BATTERY POSITIVE CIRCUIT VOLTAGE.
• BACKPROBE EGR VALVE VSV
SOLENOID ENGINE
CONTROL MODULE CIRCUIT.
TEST LIGHT SHOULD
BE "ON". IS IT?
I
$ $
RESTRICTED VACUUM SOURCE OPEN
IN CIRCUIT OR OR FAULTY SOLENOID FAULTY ENGINE
CONTROL MODULE

CD
®
DRIVEABILITY AND EMISSIONS 6E2-77
DIAGNOSTIC TROUBLE CODE (DTC) 33A
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR CIRCUIT
(SIGNAL
VOLTAGE HIGH-LOW VACUUM)
• IF ENGINE IDLE IS ROUGH, UNSTABLE, OR INCORRECT, CORRECT CONDITION BEFORE USING CHART. SEE "SYMPTOMS" IN SECTION "B". • ENGINE IDLING
• DOES "SCAN TOOL" DISPLAY A MANIFOLD ABSOLUTE PRESSURE (MAP)
VOLTAGE OF 4.0 VOLTS OR OVER?
~ $
• IGNITION "OFF". •
DOES "SCAN TOOL" DISPLAY
• DISCONNECT MAP SENSOR ELECTRICAL CONNECTOR. MAP SENSOR VOLTAGE LESS
• IGNITION "ON". THAN 1 VOLT? • "SCAN TOOL" SHOULD READ A VOLTAGE OF 1 VOLTS I OR LESS.
DOES IT?
$ $
DIAGNOSTIC TROUBLE
CODE l REFER TO J (DTC) 33A DTC
33B CHART. IS INTERMITTENT. IF NO ADDITIONAL DTC(S) WERE STORED, REFER TO "DIAGNOSTIC AIDS" ON FACING ~-
~ $
• PROBE SENSOR GROUND CIRCUIT WITH MAP SIGNAL CKT SHORTED TO A TEST LIGHT TO BATTERY POSITIVE VOLTAGE,
SHORTED TO 5 VOLT
VOLTAGE. REFERENCE CKT, OR FAULTY • TEST LIGHT SHOULD LIGHT. ENGINE CONTROL MODULE.
DOES IT?
$ $
PLUGGED OR LEAKING OPEN SENSOR GROUND CIRCUIT.
SENSOR VACUUM HOSE OR FAULTY MAP SENSOR.
CLEAR DTC(S) AND CONFIRM "CLOSED LOOP" OPERATION AND NORMAL "CHECK ENGINE" MALFUNCTION INDICATOR LAMP OPERATION.

DRIVEABILITY AND EMISSIONS 6E2-79
DIAGNOSTIC TROUBLE CODE (DTC) 338
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR CIRCUIT
(SIGNAL VOLTAGE LOW-HIGH
VACUUM)
CD • ENGINE IDLING
DOES "SCAN TOOL" DISPLAY MAP VOLTAGE BELOW .25 VOLTS?
@ • IGNITION "OFF".
• DISCONNECT SENSOR ELECTRICAL CONNECTOR.
•
JUMPER HARNESS TERMINALS "2" TO "1". • IGNITION "ON". • MANIFOLD ABSOLUTE PRESSURE VOLTAGE SHOULD READ OVER 4 VOLTS.
DOES IT?
@ • IGNITION "OFF"
• REMOVE JUMPER WIRE.
• PROBE TERMINAL "B" GREY /RED WIRE WITH 'W' A TEST LIGHT TO BATTERY POSITIVE VOLTAGE. • IGNITION "ON". • "SCAN TOOL" SHOULD READ OVER 4 VOLTS.
DOES IT?
5 VOLT REFERENCE CIRCUIT OPEN OR SHORTED
TO GROUND OR FAUL TV ENGINE CONTROL MODULE.
DTC 33B IS INTERMITTENT. IF NO ADDITIONAL DTC{S) WERE STORED, REFER TO "DIAGNOSTIC AIDS" ON FACING p
GRY/RED WIRE OPN OR GRY/RED WIRE SHORTED TO GROUND OR GRY/RED WIRE SHORTED TO SENSOR GROUND OR FAUL TV ENGINE CONTROL MODULE.
CLEAR DTC{S) AND CONFIRM "CLOSED LOOP" OPERATION AND NORMAL "CHECK ENGINE" MALFUNCTION INDICATOR LAMP OPERATION.

CD
®
DRIVEABILITY AND EMISSIONS 6E2-81
DIAGNOSTIC TROUBLE CODE (DTC) 42
IGNITION CONTROL (IC) CIRCUIT
• CLEAR DIAGNOSTIC TROUBLE CODES (DTCs). • IDLE ENGINE FOR 1 MINUTE OR UNTIL DTC 42 SETS.
DOES DTC 42 SET?
~ $
• IGNITION "OFF" DTC 42 INTERMITTENT.
• DISCONNECT ENGINE CONTROL MODULE (ECM) REFER TO "DIAGNOSTIC AIDS" ON
CONNECTORS. FACING~ • IGNITION "ON".
• OHMMETER SELECTOR SWITCH IN THE 1 000 TO 2000
OHMS RANGE. • PROBE ECM HARNESS CONNECTOR IGNITION CONTROL (IC) CKT WITH AN OHMMETER TO GROUND. IT SHOULD READ LESS THAN 1000 OHMS.
DOES IT?
~ $
• PROBE ECM HARNESS CONNECTOR BYPASS CKT WITH OPEN IC CKT, FAULTY CONNECTION OR FAULTY
I A TEST LIGHT TO BATTERY POSITIVE VOLTAGE. ELECTRONIC IGNITION MODULE.
L LIGHT "OFF" I LIGHT "ON" I
I
• WITH OHMMETER STILL CONNECTED TO ECM HARNESS • DISCONNECT IC MODULE 4-wAY CONNECTOR. IC CKT AND GROUND. L AGAIN PROBE ECM HARNESS BYPASS CKT WITH THE TEST
I I
LIGHT CONNECTED TO BATTERY VOLTAGE. (AS TEST LIGHT
LIGHT "ON" j LIGHT"OFF" I CONTACTS BYPASS CKT, RESISTANCE SHOULD SWITCH
FROM UNDER 1000 TO OVER 2000 OHMS.) I l DOES IT? BYPASS CKT SHORTED I FAULTY IGNITION I
TO GROUND. MODULE.
~ $
•
DISCONNECT 6-WAY CONNECTOR AT ELECTRONIC ® • RECONNECT ECM AND IDLE ENGINE FOR ONE
IGNITION MODULE. MINUTE OR UNTIL CODE 42 SETS.
NOTE OHMMETER THAT IS STILL CONNECTED TO
DOES CODE SET? IC CKT AND GROUND. RESISTANCE SHOULD HAVE GONE I HIGH (OPEN CIRCUIT).
DOES IT?
$ $
$ $
FAULTY ECM I DTC 42 INTERMITTENT. REFER TO "DIAGNOSTIC
AIDS" ON FACING
BYPASS
CKT OPEN, IIC CKT SHORTED TO ~ FAULTY CONNECTIONS GROUND. OR FAULTY IGNITION MODULE.

will not light when connected to the circuit. In some
cases, even an ordinary shop voltmeter
will not give an
accurate reading because its resistance is
too low.
Therefore, a 10 megohms input impedance digital
voltmeter is required to assure accurate voltage
readings.
The Engine
Control Module (ECM) controls output
circuits such as the fuel injectors, idle air control valve,
air conditioning clutch relay, etc. by controlling the
ground circuit through transistors
or a device called a
"quad-driver".
INFORMATION SENSORS
Engine Coolant Temperature (ECT) Sensor
(Fig. 6E2-51)
The Engine Coolant Temperature (ECT) Sensor is a
thermistor
(a resistor which changes value based on
temperature) mounted in the engine coolant stream.
Low ECT produces a high resistance (1 00,000 ohms at
-40.C/-40.F) while high temperature causes low
resistance (70 ohms at 130.C/266.F).
The ECM supplies a 5-volts signal to the ECT sensor
through a resistor in the
ECM and measures the
voltage. The voltage
will be high when the engine is
cold, and low when the engine is hot.
By measuring the voltage, the
ECM knows the ETC.
ECT affects most systems the ECM controls.
A failure in the
ECT sensor circuit should set a
Diagnostic Trouble Code
(DTC) 14. Remember, these
DTC(s) indicate a failure in the
ETC circuit, so proper
use
of the chart will lead to either repairing a wiring
problem or replacing the sensor, to properly repair a
problem.
1. Engine coolant temperature sensor
2. Harness connector to ECM
3. Locking tab
Fig. 6E2-51
Intake Air Temperature (IAT) Sensor
The Intake Air Temperature (IAT) sensor is a
thermistor, a resistor which changes
value based on
the temperature
of air entering the engine. Low
temperature produces a high resistance
(1 00,000
ohms at -4o·c/-40.F), while high temperature causes
low resistance (70 ohms at 130.C/266.F).
The ECM supplies a 5-volts signal to the sensor through
a resistor in the
ECM and measures the voltage. The
voltage
will be high when the intake air is cold, and low
DRIVEABILITV AND EMISSIONS 6E2-1 01
when the air is hot. By measuring the voltage, the ECM
knows the lAT.
The IAT sensor is also used to control spark timing and
delays exhaust gas recirculation when intake air is
cold.
A failure in the IAT sensor circuit should set a DTC 23.
Heated Oxygen Sensor (H02S) (Fig. 6E2-52)
The Heated Oxygen Sensor (H02S) is mounted in the
exhaust system where
it can monitor the Oxygen (02)
content of the exhaust gas stream. The 02 content in
the exhaust reacts
with the sensor to produce a voltage
output. This voltage ranges
from approximately .1 volt
(high 02-lean mixture) to .9 volt (low 02-rich mixture).
This voltage can
be measured with a digital voltmeter
having at
least 10 megohms input impedance. Use of
standard shop type voltmeters will result in very
inaccurate readings.
By monitoring the voltage
output ofthe H02S, the ECM
will know what fuel mixture command to give to the
injector
(lean mixture-low 02 voltage= rich command,
rich mixture-high
02 voltage= lean command).
The
H02S circuit, if open, should set a DTC 13. A
constant
low voltage in the sensor circuit should set a
DTC 44. While a constant high voltage in the circuit
should set a DTC 45. DTC(s) 44 and 45 could also be set
as a result of fuel system problems. See DTC charts for
conditions that can cause a lean or rich system.
The
H02S works in the same manner as the non-H02S
The exception is that battery positive voltage is
supplied to a heating unit that is part of the sensor
itself. This heater receives voltage
from the ECM's
main
relay circuit.
The heater
helps to heat up the H02S so the ECM can
start
controlling the fuel injection sooner for better fuel
emissions. There are no malfunction DTC(s) to detect if
the heater part of the sensor is working. To check the
heater, refer to "Functional
Check" in this section.
Fig. 6E2-52
~
\W

Park/Neutral Position (PNP) Switch (Auto Only)
The Park/Neutral position (PNP) switch indicates to the
Engine Control Module
(ECM) when the transmission
is in park, neutral
or drive. This information is used for
the exhaust gas recirculation, and the idle air control
valve operation.
NOTE:
• Vehicle
should not be driven with PNP switch
disconnected,
as idle quality will be affected and a
possible false diagnostic trouble code
(DTC) 24
(vehicle speed sensor).
DRIVEABILITY AND EMISSIONS 6E2-103
See DIAGNOSIS AND GENERAL SERVICE Section for
more information on the PNP switch. The PNP switch is
part
of the neutral/start and backup light switch
assembly mounted on the transmission.
See CHART C-
1 A for PNP switch check.
DIAGNOSIS
To read the DTC(s), use a "Scan tool" or ground the
diagnostic test terminal,
with the engine not running
and the ignition
"ON". The "Check Engine" malfunction
indicator lamp
will flash DTC 12 three times and then
flash each
DTC stored in memory three times. All
DTC(s) stored in memory will have been read when
DTC 12 is flashed again.
No new
DTC(s) can be stored when in the diagnostics
test mode (diagnostics lead grounded). This
eliminates confusion while the system is being
serviced.
To clear the
DTC(s) from memory:
• Ignition "OFF".
•
Disconnect main fuse located in the under hood
fuse/relay center near the battery.
Since the ECM can have a failure which may affect only
one circuit, following the diagnostic procedures in this
section
will determine which circuit has a problem and
where
it is.
If a diagnostic chart indicates thatthe ECM connections
or ECM is the cause of a problem, and the ECM is
replaced,
but does not correct the problem, one of the
following may be the reason.
• There is a problem with the ECM terminal
connections-The diagnostic chart will say ECM
connections or ECM. The terminals may have to
be removed from the connector in order to check
them properly.
• The ECM is not correct for the Vehicle-Ane
incorrect
ECM may cause a malfunction and may
set a DTC.
• The problem is intermittent -This means that
the problem is
not present at the time the system is
being checked.
In this case, refer to the
"Symptoms" portion of the manual and make a
careful physical inspection
of all portions of the
system involved.
• Shorted solenoid, relay coil, or harness
Solenoid and relays are turned "ON" and "OFF" by
the
ECM, using internal electronic switches called
"drivers".
Each driver is part of a group of four,
called "quad-drivers". Failure of one driver can
damage any other driver in the set. A
shorted solenoid, relay coil, or harness in a l-EFT­
SHCI
computer will not damage the ECM, but will
cause the circuit and controlled component to be
inoperative. When the circuit fault is not present or
has been repaired, the "quad-driver" will again
operate in a normal manner due to its fault
protected design. If a fault has been repaired in a
circuit controlled by a "quad-driver", the original
ECM should be reinstalled and the circuit checked
for proper operation. ECM replacement will not be
necessary if the repaired circuit or component now
operates correctly.
J 34636 or BT-8405 testers or equivalent provide a fast,
accurate means
of checking for a shorted coil or a short
to battery positive voltage.
• The replacement ECM may be faulty-After the
ECM is replaced, the system should be re-checked
for proper operation. If the diagnostic chart again
indicates the
ECM is the problem, substitute a
known good
ECM. Although this is a rare
condition,
it could happen.
ENGINE CONTROL MODULE (ECM)
A faulty ECM will be determined in the diagnostic
charts.
ELECTRONICALL V ERASABLE
PROGRAMMABLE READ
ONL V MEMORY
A faulty electrically erasable programmable read only
memory, which is part of the ECM, will set a DTC 51.
ENGINE CONTROL MODULE (ECM)
INPUTS
All of the sensors and input switches can be diagnosed
by the use
of "Scan tool".
Following is a short description of how the sensors and
switches can be diagnosed by the use
"Scan tool". The
"Scan tool" can also be used to compare the values for
a normal running engine with the engine you're
diagnosing.

wcAUTION:
' • When replacing the production Engine Control
Module
(ECM) with a service ECM (controller),
it is important to transfer the broadcast
diagnostic
trouble code and production ECM
number to the service ECM label. Please do not
record on ECM cover. This will allow positive
identification
of ECM parts throughout the
service
life of the vehicle.
DRIVEABILITV AND EMISSIONS 6E2-1 05
\fCAUTION:
' • To prevent internal ECM damage, the ignition
must be
"OFF" when disconnecting or
reconnecting power
to ECM (for example;
battery cable, ECM pigtail, ECM fuse, jumper
cables etc.)
ENGINE CONTROL MODULE (ECM) REPLACEMENT
Removal steps 1. Negative battery cable 2. Lower trim panel at console
3. A/C Heater transfer tube ECM 4. ABS controller electrical
controller
5. ABS controller 6. Four fasteners for ECM bracket
7. ECM electrical connectors
8. ECM from under dash bracket still attached
Installation steps To install, follow the removal steps
reverse in the order.
Fig. 6E2-55
EJ REMOVAL
1. Negative battery cable
2. Lower trim panel at console (4 fasteners)
3. Air Conditioning Heater transfer tube
4. ABS controller electrical connector (1) (if
equipt)
5. ABS controller (4 fasteners) (if equipt)
6. Four (4) fasteners for ECM bracket
7. ECM
electrical connectors (2)
8. ECM from under dash, bracket
still attached
NOTE:
To prevent possible Electronic Discharge damage
to the ECM, Do not touch the connector pins or
soldered components on the circuit board.
I•+! INSTALLATION
1. ECM and bracket under dash
2. Four (4) fasteners and tighten
3. Two (2) ECM electrical connectors
4. ABS controller and four (4) fasteners (if equipt)
5. ABS controller electrical connector (if equipt)
6. Air Conditioning Heater transfer tube
7. Lower trim panel at console (4 fasteners)
8. Negative battery
cable
Functional
Check
1. Turn ignition "ON".
2. Enter diagnostics test mode.
A.
Allow Diagnostic Trouble Code (DTC) 12 to
flash four times to verify no other DTC(s) are
present. This indicates the reprogrammed
ECM is functioning properly.
B. If DTC 51 occurs, or if the malfunction
indicator lamp is "ON" constantly with no
DTC(s), the
ECM is defective.
• If it is necessary to replace the ECM, follow
the previous removal instructions.
ENGINE COOLANT TEMPERATURE (ECT)
SENSOR
Fig. 6E2-56

6E2-1 06 DRIVEABILITV AND EMISSIONS
1••1 REMOVAL
\f7 CAUTION:
Y/ Care must be taken when handling Engine
Coolant Temperature (ECT) sensor. Damage to
ECT sensor will affect proper operation of the fuel
injection system.
Preparation: • Negative battery cable.
•
Drain engine coolant system.
1. Inlet manifold assembly
• Refer to "Fuel metering system" section "6E2-
C2"
for removal procedure.
2. Electrical connector
3. ECT sensor
• Remove from rear of engine coolant transfer
tube.
I••IINSTALLATION
3. ECT sensor
• Apply sealer or equivalent to threads only.
•
Tighten the ECT sensor to the specified torque
~~~ Torque N·m (lb·ft) I 30 (22)
2. ECT sensor connector
1. Intake manifold assembly
• Refer to "Fuel metering system" section "6E2-
C2" for installation.
INTAKE AIR TEMPERATURE (IAT)
SENSOR
Fig. 6E2-57
1••1 REMOVAL
Preparation: • Negative battery cable.
1. Wiring connector
• Disconnect connector from Intake Air
Temperature (IAT) sensor.
2. IAT sensor
I••IINSTALLATION
2. IAT sensor
• Apply sealer or equivalent to threads only.
•
Tighten the IAT sensor to the specified torque.
~~~ Torque N·m (lb·ft) 30 (22)
1. Wiring
connector
HEATED OXYGEN SENSOR (H02S)
Fig. 6E2-58
1••1 REMOVAL
'fCAUTION
• The Heated Oxygen Sensor (H02S) uses a
permanently attached pigtail and connector.
This
pigtail should not be removed from the
H02S. Damage or removal of the pigtail or
connector
could affect proper operation of the
H02S.
•
Take care when handling the H02S. The in-line
electrical
connector and louver end must be
kept free
of grease, dirt, or other contaminants.
Also, avoid using cleaning solvents of any type.
Do not drop or roughly handle the H02S.
Preparation: • Battery negative cable.
1. H02S wiring connector
2. H02S
• The H02S may be difficult to remove when
engine temperature is
below 48• (120.).
•
Excessive force may damage threads in
exhaust pipe.
I••IINSTALLATION
2. H02S
• A special anti-seize compound is used on the
H02S threads. The compound consists of a
liquid graphite which will burn away, but the
glass beads will remain, making the sensor
easier
to remove.
•

New or service sensors will already have the
compound
applied to the threads. If a sensor is
removed
from an engine and iffor any reason it
is to be reinstalled, the threads must have anti­
seize compound
applied before reinstallation.
•
Apply anti-seize compound or equivalent to
threads of oxygen sensor if necessary.
• Tighten the oxygen sensor to the specified
torque.
1~1 Torque N·m (lb·ft) 55 (40)
1. H02S wiring connector
THROTTLE POSITION (TP) SENSOR
Fig. 6E2-59
E) REMOVAL
Preparation: • Battery negative cable.
1. Throttle Position (TP) sensor wiring connector
2. TP sensor fixing screw
3. TP sensor
I••IINSTALLATION
3. TP sensor
2. TP sensor fixing screw
• Tighten the fixing screw to the specified torque.
~~~ Torque N·m (lb·in) I 2 (18)
• Use a "Scan tool" to check TP sensor output
voltage with throttle closed, should be under
0.85 volts. If over 0.85 volts, check for binding
throttle shaft, or TP sensor lever. If all OK,
replace TP sensor.
1.
TP sensor wiring connector
DRIVEABILITY AND EMISSIONS 6E2-1 07
MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR
1. Vacuum hose
) 0~
2 .• ,.~,,~,~
conne~ JJJ
4. Sensor
Fig. 6E2-60
E) REMOVAL
Preparation: • Battery negative cable.
1. Vacuum hose
2. Electrical connector
3. Attaching screws
4. Sensor
I••IINSTALLATION
4. Sensor
3. Attaching screws
2. Electrical connector
1. Vacuum hose
VEHICLE SPEED SENSOR (VSS)
Refer to INSTRUMENT PANEL CLUSTER AND
CONSOLE of this manual for replacement of vehicle
speed sensor located in instrument panel.
POWER STEERING PRESSURE (PSP)
SWITCH
Refer to STEERING, SUSPENSION, TIRES AND
WHEELS for service of the power steering pressure
switch.
PARK/NEUTRAL
SWITCH POSITION
(PNP}
See
Section AUTOMATIC TRANSMISSION GENERAL
INFORMATION Section for park/neutral position
switch.
"On-Vehicle Service" and adjustment
procedures are
also listed there.