panel JAGUAR X308 1998 2.G Workshop Manual

10. Releasing lower ends , withdraw headrest guide tubes and
trims from support boxes.

11. Release squab cover from the eight armrest aperture securing tangs.

12. Remove and discard all hog rings securing cover to outer
edge of frame.

13. Release cover retaining strip from frame top and free cover
from cushion edges.
14. Position cover for access an d remove and discard 17 hog
rings securing cover left hand panel to frame.

Installation

15. Position cover for access an d remove and discard 17 hog
rings securing cover right hand panel to frame.
16. Remove cover from seat squab.
1. Position cover on front of squab.

2. Secure cover right hand panel to frame using 17 hog rings.
3. Secure cover left hand panel to frame using 17 hog rings.

4. Position squab for access and pull cover over squab pad.

5. Ensuring that top of cover is ev enly tensioned, fit and fully seat retaining strip on frame.

Seating - Rear Seat Cushion Removal and Installation
Removal
Installation

1.
Heated rear seat only. Remove battery cover and disconnect ground
cable from battery terminal. Refer to 86.15.19.

2. Slacken, remove and discard 1/4 turn fastener securing each
heelboard trim panel and withdraw both panels for access.

3. Slacken and remove the seat cushion securing screws.

4. Raise rear of cushion, disconnect heater element harness multiplugs
(if fitted), and move cushion forw ard carefully feeding seat belt
buckles past cushion cut-outs.
5. Remove seat cushion from vehicle.
1. Holding outer seat belts clear, posi tion cushion in vehicle with rear
edge raised.
2. Position buckle assemblies and carefully feed them past cut-outs in
cushion.
3. Heated seat only. Connect heat er element harness multiplugs.
4. Fit and fully tighten cushion front securing screws.
5. Using new 1/4 turn fasteners, fi t and secure heelboard trims.
6. Reposition seatbelts.
7. Heated seat only. Fit ground cable to battery terminal and fit battery
cover. Refer to 86.15.15.

Seating - Rear Seat Cushion Cover
Removal and Installation
Removal
1. Remove rear heel boards.
2. Remove rear seat cushion. Refer to 76.70.37.
3. Place seat cushion inverted on clean work surface.

4. Remove and discard the eight hog rings securing cover at each
seat belt anchor aperture.

5. Remove and discard hog rings se curing outer edges of cover
and cushion to frame.

6. Remove and discard two hog ri ngs securing centre panel
overlap plastic edge fastener and release fastener from frame.

7. Withdraw centre overlap thro ugh cushion for access.and
remove and discard hog rings secu ring horizontal seam of right
hand panel to cushion.

Installation

8. Remove and discard the six ho g rings securing right hand
panel to centre of cushion.
9. Remove and discard seven hog ri ngs securing outer side of
cover left hand panel to cushion.
10. Remove and discard the four ho g rings securing horizontal
seam of left hand panel to cushion.
11. Remove and discard the six hog rings securing securing cover
left hand panel to centre of cushion.
12. Withdraw cover from seat belt anchor apertures.
13. Remove cover from cushion.
1. Position cover on cushion.

2. Secure cover right hand panel to centre of cushion using six
hog rings .

3. Position cover right hand hand panel through cushion seat belt
anchor aperture and secure hori zontal seam to cushion using
four hog rings.
4. Position cover and pass cent re overlap through cushion.
5. Secure outer side of cover righ t hand panel to cushion using
seven hog rings.

6. Secure cover left hand panel to centre of cushion using six hog
rings.
7. Position cover left hand panel th rough cushion seat belt anchor
aperture.
8. Secure horizontal seam of cover left hand panel to cushion
using four hog rings.
9. Position cover and pass cent re overlap through cushion.
10. Secure outer side of cover left hand panel to cushion using
seven hog rings.

11. Invert cushion assembly, fully se at cover centre panel overlap plastic edge fastener on frame and secure with two hog rings

12. Ensuring even tensioning, secu re outer edges of cover and
cushion to frame using hog rings.
13. Position cover at seat belt an chor apertures and secure each
with eight hog rings.

6. Push trim upwards to release keyhole aperture from squab
fixing and partially withdraw trim for access.

7. Slacken and remove seat belt lower anchor securing bolt.

8. Carefully withdraw seat belt and anchor plate through trim
aperture and escutcheon.
9. Remove side trim panel from vehicle.

10. Slacken and remove the seat squab outer securing bolt.
11. Slacken and remove the seat squab inner securing bolt.

Installation


12. Disconnect seat motor and squab heater harness multiplugs.

13. Slacken and remove four bolts securing seat frame to floor
and remove seat from vehicle.
1. Position seat in vehi cle and fit but do not tighten four bolts
securing frame to floor.
2. Fit and fully tighten the two bolt s securing squab frame to rear
panel.
3. Fully tighten bolts securing frame to floor.
4. Connect seat motor and squab heater harness multiplugs.
5. Position side trim panel and carefully pass seat belt lower
anchor through escutcheon and trim aperture.
6. Fit and tighten seat belt anchor securing bolt.
7. Position side trim and push do wnwards to engage keyhole on
squab outer fixing.
8. Position trim lower end over st ud and fit and fully seat new
scrivet.
9. Position seat cushion for access and connect cushion heater
harness multiplug.
10. Push seat cushion rearwards to engage it in rear securing
lugs.

Glass, Frames and Mechanisms - Front Door Window Control Switch
Removal and Installation
Removal
Installation

1.
Remove casing/armrest asse mbly from door. Refer to
76.34.01.

2. Slacken and remove armres t front securing screw.

3. Position armrest for access, slacken and remove two
switchpack securing screws and remove switchpack assembly from armrest.

4. Slacken and remove screws securing veneer panel to
switchpack.
1. Position veneer panel on sw itchpack and fit and tighten
securing screws.
2. Position switchpack assembly on armrest and fit and tighten
securing screws.
3. Fit and tighten screw securing fr ont of armrest to door casing.
4. Fit casing/armrest assembly to door. Refer to 76.34.01.

Glass, Frames and Mechanisms - Rear Door Window Control Switch
Removal and Installation
Removal
Installation

1.
Remove casing/armrest asse mbly from door. Refer to
76.34.04.
2. Remove armrest from casing. Refer to 76.34.23.

3. Position armrest for access, slacken and remove two
switchpack securing screws and remove switchpack assembly from armrest.

4. Slacken and remove screws securing veneer panels to switch
and ashtray.
1. Position veneer panels on sw itch and ashtray, and fit and
tighten securing screws.
2. Position switch/ashtray assembly on armrest and fit and
tighten securing screws.
3. Fit armrest to door casing. Refer to 76.34.23.
4. Fit casing/armrest assembly to door. Refer to 76.34.04.