JAGUAR X308 1998 2.G Manual Online

1
. Install special tool 211-098 on tie rod ball joint.
2. Tighten tool bolt to rele ase taper pin from vertical
link.

16
.
Remove nut securing upper wish bone ball joint to vertical
link.

17
.
CAUTION: Do not use special tool 211-098 in the
following procedure as this will damage the ball joint gaiter.
Release upper wishbone ball joint from vertical link/hub
assembly.
1. Install special tool 204-192 on ball joint.
2. Tighten tool bolt to rele ase ball joint taper pin from
vertical link.

18
.
Slacken but do not remove nut securing lower wishbone ball
joint to vertical link.
19. CAUTION: Do not use special tool 211-098 in the
following procedure as this will damage the ball joint gaiter.
Release lower wishbone ball joint from vertical link/hub
assembly.

1.
Install special tool 204-293 on ball joint.
2. Tighten tool bolt to rele ase ball joint taper pin from
vertical link.
20. Remove special tool 204-293 from ball joint.

21 . R
emove vertical link/hub assembly.
Support
ing ver
tical link/ hu
b assembly, remove lower
wishbone ball joint nut.
R e
move vertical link /hub assembly.

22 . R
emove stabilizer bar link to
wishbone securing nut and bolt.

23 . R
emove wishbone front arm to
rear arm securing bolt .
24. Slacken but do not remove shock absorber lower nut and
bolt.

25
.
Release lower steering column from pinion shaft.
1. Remove lower steering column nut and bolt.
Move column up
wards to release it from pinion shaft.

26
.
Disconnect harness connector from steering transducer.

27
.
Remove tiestrap securing retu rn pipe, harness (RHD only)
and rubber support to steering rack.
28. CAUTION: Do not allow steerin g pipes to support weight
of steering rack.
Position steering rack for access.
Pi
vot steering arm fully downwards

In
stallation

Re
move steering rack securing bolts.
Carefully move steer

ing rack
downwards for access to
wishbone eccentric bolt.

29 . R
emove lower wishbone rear
arm eccentric bolt and nut.
Mark position of eccentri
c bo
lt large graduation mark on
crossbeam.
R e
move wishbone rear ec
centric bolt and nut.
30. Remove lower wishbone rear arm/ball joint assembly from
crossbeam.

1. Positi
on wishbone rear arm on crossbeam and install but do
not tighten eccentric bolt.

2. Install steeri
ng rack on crossbeam.
Ensure
that b
ushes are correct
ly positioned on steering
rack.
Posi ti
on steering rack on crossbeam.
Position support brac
kets over bus
hes.
Install mountin
g bracket bolts an
d tighten to 41-54Nm.
3. Install lower steering column on pinion shaft.
Move col u
mn downwards to engage coupling splines on
pinion shaft.

1
. Install nut and bolt and tighten to 22-28Nm.

4. Position an
d connect harnes
s to steering transducer.
RHD
vehicles. Position steeri
ng harness behind return
pipe.
Conne
ct harness to transducer.

5. Secure return pipe on steering
rack.
1. Position pipe rubber support on steering rack.
2. Position pipe on support .
3. RHD vehicles. Position harness on pipe support rubber.
4. Secure pipe and harness to support with new tiestrap.

6. Inst
all shock absorber
and mounting bracket.
Posit
ion shock absorber moun
ting bracket on wishbone
rear arm.
Install
wishbone front arm to
rear arm bolt and tighten to
77-103Nm.
7. Tighten shock absorber lower bolt and nut to 43-57Nm.

8. Position an
d partially tighten
wishbone rear eccentric bolt.
Rotate
eccentric bolt to align large graduation with mark
made during removal.
Ens u
ring bolt remains in position, partially tighten nut.

9. Install stabil
izer bar link to wi
shbone securing nut and bolt and
tighten to 41-54Nm.

10 . Position verti
cal link/ hub asse
mbly on lower ball joint taper
pin, install nut and tighten to 60-80Nm.
11. Position vertical link/ hub asse mbly on upper ball joint taper
pin.

12
.
Install nut securing upper ball jo int to vertical link and tighten
to 60-80Nm.

13
.
Position tie rod ball joint taper pin on steering arm and install
and tighten nut to 71-85Nm.
14. Raise vehicle and support on st ands to provide access for
Special Tool 204-111 and road spring.

15
.
Install spring pan, rubber lowe r seat, spring and rubber upper
seat on Special Tool 204-111.
16. Install road spring in suspension turret.
Install
spring pan/spring as
sembly and Special Tool 204-
111 in suspension turret.

Ensure spring
upper se
at is correctly positioned in turret.
Engage tool dowel in turret slo
t.
R
o
tate adjuster of Special Tool 204-111 to lightly tension
spring.

17 . Ins
tall guide pins ( supplied with Special Tool 204-111) in
spring pan/wishbone bolt locations.

18 . WARNING: WHE
N ROTATING TOOL ADJUSTER, ENSURE
THAT TOOL STEM DOES NOT TU RN AND DISTURB POSITION OF
DOWEL IN SUSPENSION TURRET.
Install spring pan to wishbone securing bolts.
Ro t
ate tool adjuster to gradua
lly increase spring tension.
Pr
ogressively install but do no
t tighten spring pan securing
bolts.
Tigh ten spring pan
bolts to 70-90Nm.
Ensure spri
ng
lower seat is co
rrectly positioned in spring
pan.

19 . WARNING: WHE
N ROTATING TOOL ADJUSTER, ENSURE
THAT TOOL STEM DOES NOT TU RN AND DISTURB POSITION OF
DOWEL IN SUSPENSION TURRET.
Remove Special Tool 204-111 from suspension.
Rotat
e adjuster of Special Tool to release tension on
spring.
R otate
tool stem to release dowel from turret.
With
draw tool and adaptor
.assembly.
20
. Lower vehi
cle to working heig
ht and support on stands.
21. Install wheel speed sensor.
Positi
on wheel speed sensor on vertical link.

Inst
all sensor bolt an
d tighten to 8-10Nm.

22
.
Connect wheel speed sensor harness.
1. Connect wheel speed sensor harness to sensor.
2. Using new tiestraps secure wheel speed sensor harness to upper wishbone.

23
.
Install brake calipers.
R
emove tie supporting brake caliper.
1. Install caliper on carrier.
2. Install guide pins.
3. Install guide pin dust caps.
4. Install caliper spring clip.
24. Install road wheel. Re fer to Section 100-02.
25. Raise vehicle, remove stands and lower vehicle onto road
wheels.

26
.
Ensuring graduation mark remains aligned, finally tighten
wishbone rear eccentric bolt to 113-153Nm.
27. Check wheel alignment and if necessary adjust. Refer to
57.65.01.

Front Suspension - Rear Lower Arm Bushing
Remo
val and Installation
Remov
a
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. Refer to Section 100-00 for further
information.
S p
ecial Tool(s)

R
o
ad spring compressor
204-111 (JD115)

Taper separator
2
11-098 (JD 100)

Ball
Jo
int Taper Separator
204-192 (JD 219)

Bal l
joint splitter
204-293
1. Ra
ise front of vehicle and support on stands. Refer to Section
100-02.
2. Remove appropriate road wheel. Refer to Section 100-02.

3. CAUTIO
N: Do not suspend caliper from brake hose as
this will damage the hose.
Remove brake calipers from carriers. 1. Remove caliper spring clip.
2. Remove guide pin dust caps.
3. Slacken and withdraw guide pins.
4. Remove caliper from carrier and tie to suspension mounting bracket.
4. Ra
ise vehicle further to provid
e access for Special Tool 204-