Bolt JAGUAR XFR 2010 1.G Workshop Manual

5. CAUTIONS:


The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.


Make sure that no components fall off during removal.

NOTES:


Make sure that the crankshaft is not rotated.


Make sure the crankshaft and flexplate mating faces are clean before
installation.


6.
7.
8.

Installation

1. Torque: 8 Nm 2. CAUTIONS:


Make sure that the mating faces are clean and free of foreign material.


Use only a plastic scraper when removing the sealing material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas
shown, and tighten the bolts within 7 minutes.



























3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 25 Nm

4. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Use only a plastic scraper when removing the sealing material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas
shown, and tighten the bolts within 7 minutes.
















5. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm





















6. CAUTION: Make sure that the mating faces are clean and free of foreign
material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas shown, and
tighten the bolts within 7 minutes.

7. CAUTION: Make sure that the mating faces are clean and free of
foreign material.


NOTE: Install new lower timing cover.

Install the bolts, but do not tighten fully at this stage.

Special Tool(s): 303-1433

























8. NOTE: Tighten the bolts in the indicated sequence.
Torque:
M6 12 Nm M8 20 Nm








9. Remove the special tool.

10. Torque: 12 Nm

11.
12. Torque: 10 Nm
















Special Tool(s): 303-1442, 303-1443
















13. Remove the special tools.


14. NOTE: Tighten the bolts in the indicated sequence.

Torque: 11 Nm www.JagDocs.com

23.
24.
25. Loosen the Torx screws half a turn each.




































CAUTIONS:


Install new high-pressure fuel supply lines.


Lubricate only the union threads with clean engine oil.

NOTES:


Remove and discard the blanking caps.


Install the bolt and unions fully finger tight before final tightening.

31.
32.
33. NOTES:


Install the bolt and unions finger tight before final tightening.


Remove and discard the blanking caps.

Torque:
Unions 21 Nm M6 11 Nm















Torque:
Unions 21 Nm















Torque:
M10 29 Nm M6 11 Nm

45.
46.
47.
48. Torque: 12 Nm


















CAUTION: Install all the bolts finger tight before final tightening.

Torque: 25 Nm

































CAUTION: Install all the bolts finger tight before final tightening.


NOTE: Tighten the bolts in the indicated sequence.

Torque: 48 Nm www.JagDocs.com

49. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.


Install the bolts in the noted position.

NOTES:


Make sure that the crankshaft is not rotated.


Make sure the crankshaft and flexplate mating faces are clean before
installation.


Tighten the retaining bolts working diagonally.

Torque:
Stage 1:45 Nm Stage 2:90°
50. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
51. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

52. Lower the vehicle.

53. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. NOTE: Tighten the bolts in the indicated sequence.

Torque: 12 Nm





















4. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm