display Lancia Delta 2010 Owner handbook (in English)

GETTING TO KNOW YOUR CAR15
1
Cleaning DPF (particulate filter) in
progress (only Multijet versions with
DPF - amber)
When the ignition key is turned to MAR (ON),
the warning light switches on but it must switch off after
a few seconds. The warning light comes on constantly to
notify the driver that the DPF system needs to eliminate
captured pollutants (particulate) by the regeneration
process. The warning light does not come on during every
DPF regeneration, but only when driving conditions re-
quire notification of the driver. To switch the warning light
off, the car must stay in motion until regeneration has been
completed. The process normally takes about 15 minutes.
The optimum conditions to end the process are achieved
by keeping the car in motion up to 60km/h with an en-
gine speed higher than 2,000 rpm. This light coming on
is not a car defect and therefore the car does not need to
go to the workshop. A specific message will appear on
the display when the warning light comes on (for ver-
sions/markets, where provided).
h
Fuel reserve (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off af-
ter a few seconds. The warning light comes on
when about 5 to 7 litres of fuel are left in the tank.
The display will show a dedicated message.
IMPORTANT The warning light will blink to indicate a
system failure. Go to a Lancia Dealership to have the sys-
tem checked.
K
EOBD/injection system failure (amber)
Under normal conditions, the warning light comes
on when the ignition key is turned to MAR, but
should go off as soon as the engine is started.
If the warning light remains on or comes on whilst driving,
this means that the injection system is not working prop-
erly; in particular, if the warning light comes on constantly,
U
Steering corrector not available
This warning light (or symbol on the display) comes on
when the steering corrector is not available. The display
will show a dedicated message.Always drive at a speed appropriate to the traf-
fic conditions, the weather and speed limits. The
engine may be turned off while the DPF light is
on; however, repeated interruption of the regeneration
process may result in premature exhaustion of engine oil.
For this reason it is always advisable to wait for the li-
ght to go off before turning off the engine, following the
instructions appearing above. It is not advisable to com-
plete DPF regeneration with the vehicle stationary.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 15

16GETTING TO KNOW YOUR CAR
Go to a Lancia Dealership as soon as possi-
ble if warning light Ueither does not light
up when the key is turned to MAR or if while
travelling the warning light comes on either steady
or blinking (on some versions along with a message
on the display). The operation of the warning light
Umay be checked by the traffic police using spe-
cific devices. Follow the laws in force in the coun-
try where you are driving.
Advanced ESP system (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. If the warning light does not go off
or stays on together with the LED on the ASR button when
travelling, contact a Lancia Dealership. On certain versions
a dedicated message is displayed. If the warning light
flashes when driving, this indicates that the Advanced ESP
system has cut in.
á
Hill holder system failure (amber)
Theáwarning light turns on to indicate a Hill
holder system failure. In this case, contact a
Lancia Dealership as soon as possible. Alter-
natively, on some versions the *symbol is
lit up on the display.
The display will show a dedicated message.
á
*
To switch the warning light off, carry out the following
initialization procedure:
❍turn the ignition key to the ON position;
❍turn the steering wheel fully both clockwise and anti-
clockwise (to move from the position with the wheels
straight);
❍turn the ignition key to the OFF position and then turn
it back ON.
If the
áwarning light does not go out after a few
seconds, seek assistance from a Lancia Dealership. this indicates a malfunction in the supply/ignition system that
could cause excessive exhaust emissions, a possible loss of
performance, poor driveability and high fuel consumption.
On certain versions a dedicated message is displayed. Un-
der these conditions, the vehicle can continue travelling at
moderate speed without demanding excessive effort from
the engine. Prolonged use of the car with the warning light
on may cause damage. Go to a Lancia Dealership as soon
as possible.
The warning light goes out after the fault is cleared, and
the indication is stored in the system.
Petrol engines only
If the warning light is flashing, this indicates that the cat-
alytic converter may be damaged.
If the light flashes, release the accelerator pedal to lower
the speed of the engine until the warning light stops flash-
ing; continue the journey at moderate speed, trying to avoid
driving conditions that may cause further flashing and con-
tact a Lancia Dealership as soon as possible.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 16

GETTING TO KNOW YOUR CAR17
1
Glow plug preheating
This warning light comes on when the key is
turned to MAR. It will go out as soon as the glow
plugs have reached a predetermined temperature.
Start the engine as soon as the warning light goes out.
IMPORTANT At high outdoor temperatures the warning
light stays on for an extremely short time.
Glow plug heating failure
The warning light will blink in the event of a failure in the
glow plug preheating system. Go to a Lancia Dealership
as soon as possible.
The display will show a dedicated message.
m
Water in diesel fuel filter (Multijet
versions) (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. The warning light turns on when there is
water in the diesel fuel filter. The display will show a ded-
icated message.
c
The presence of water in the fuel system circuit
may cause severe damage to the injection sys-
tem and irregular engine operation. If the
c
warning light comes on (together with a message on the
display on some versions), go to a Lancia Dealership
as soon as possible to have the system bled. Water may
have been introduced in the tank if this appears im-
mediately after refuelling: in this case, stop the engine
immediately and contact a Lancia Dealership.
ABS system failure (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after a
few seconds. The warning light lights up when the
system is either not working or not available. Under these cir-
cumstances the braking system will work as normal with-
out the extra performance offered by the ABS system.
Drive carefully to the nearest Lancia Dealership to have the
system checked.
The display will show a dedicated message.
>
Lancia Code system failure (amber)
This warning light (or symbol on the display),
when on constantly with the ignition key turned
to MAR, indicates a possible failure (see “Lancia
Code system” in chapter 1).
Y
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 17

18GETTING TO KNOW YOUR CAR
If the Ywarning light (or symbol in the display) is blinking,
this means that the vehicle is not protected by the engine in-
hibitor device (see “Lancia Code system” in chapter 1).
Contact a Lancia Dealership to have all the keys stored.
Alarm failure
(for versions/markets, where provided)
A fault with the alarm system is signalled by this warn-
ing light (or symbol in the display) coming on. Contact a
Lancia Dealership as soon as possible.
The display will show a dedicated message.
Break-in attempt
(for versions/markets, where provided)
This warning light (or symbol on the display) comes on
when a break-in attempt is detected. Contact a Lancia
Dealership as soon as possible.
The display will show a dedicated message.The warning light (amber), or symbol on the display (red),
lights up when the inflation pressure of one or more tyres
falls below a preset level. In this way the T.P.M.S. system warns
the driver that one or more tyres may be dangerously flat and
liable to puncture (see “ T.P.M.S. system” in this chapter).
IMPORTANT Do not continue driving with one or more
tyres flat as vehicle driveability may be compromised. Stop
the car, avoiding harsh braking or steering manoeuvres. Re-
place the wheel immediately with the small spare wheel (for
versions/markets, where provided) or carry out a repair us-
ing the dedicated kit (see the paragraph on “Replacing a
wheel” in chapter 4) and contact a Lancia Dealership as
soon as possible.
Check tyre pressure
This warning light (for versions/markets, where provid-
ed) comes on when the ignition key is turned to MAR, but
it should go off after a few seconds.
The warning light (or symbol in the display) lights up to
indicate that a tyre is flat (see “T.P.M.S. system ” in this
chapter).
Should two or more tyres be flat, the display will show the
indications corresponding to each tyre in sequence. Restore
the correct inflation pressure values as soon as possible (see
paragraph “Cold inflation pressures” in chapter “6”). Insufficient tyre inflation pressure
(for versions/markets, where provided)
This warning light (or symbol on the display)
comes on when the ignition key is turned to MAR,
but it should go off after a few seconds.
n
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 18

GETTING TO KNOW YOUR CAR19
1
Particularly strong radio frequency interfer-
ence may cause the T.P.M.S. system to func-
tion incorrectly. This condition is indicated
to the driver by a message (for versions/markets,
where provided).
The warning message will go off automatically as
soon as the radio-frequency noise ceases to disturb
the system.
External lighting failure (amber)
This warning light (or symbol on the display)
comes on when a failure is detected in any of
the following lights:
❍sidelights;
❍brake lights (for versions/markets, where provided);
❍rear fog lights;
❍direction indicators;
❍number plate lights;
❍daylight lights.
W
Rear fog lights (amber)
The warning light comes on when the rear fog
lights are turned on.
4
Front fog lights (green)
The warning light comes on when the front fog
lights are turned on.
5
Direction indicators
(green - intermittent)
The warning lights turn on when the direction
indicator control lever is moved downwards,
upwards or when the hazard warning light
button is pressed.
F
D
Tyre pressure unsuitable for speed
This warning light (for versions/markets, where provid-
ed) comes on when the ignition key is turned to MAR, but
it should go off after a few seconds.
Should it be necessary to travel at a speed higher than 160
km/h, inflate the tyres to the pressure value specified in
paragraph “Inflation pressures” in chapter “6”.
If the T.P.M.S. system (for versions/markets, where pro-
vided) detects that the inflation pressure of one or more
tyres is unsuitable for the speed being maintained, it lights
up the warning light or symbol (together with a message
shown on the display) (see paragraph “Insufficient tyre
inflation pressure” in this chapter). The warning light
remains on until the vehicle speed is reduced to below a
certain threshold (see paragraph “T.P.M.S. system” in this
chapter).
IMPORTANT reduce speed immediately if this occurs.
Tyre overheating could irreparably compromise tyre per-
formance and life, and in extreme cases may even cause
the tyre to explode.The fault relating to these lights may be caused by: one or
more burnt lamps, a blown protection fuse or interruption
of the electrical connection.
The display will show a dedicated message.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 19

20GETTING TO KNOW YOUR CAR
Daylight lights/dipped beam headlights
(green)
This warning light comes on when the daytime
lights or dipped beam headlights are turned on.
Follow me home
This warning light comes on when this device is activat-
ed (see “Follow me home” in chapter “1”).
The display will show a dedicated message.
3
Main beam headlights (blue)
This warning light comes on when the main
beam headlights are turned on.
1
Cruise control system
(green)
(for versions/markets, where provided)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after a few sec-
onds. The warning light is lit up on the display by rotat-
ing the Cruise Control selector wheel to ON.
The display will show a dedicated message.
Ü
DISPLAY
The car can be equipped with a multifunctional/ recon-
figurable multifunctional display which, according to the
settings carried out, will show useful information when
driving.
MULTIFUNCTIONAL DISPLAY “STANDARD”
SCREEN fig. 4
The standard screen shows the following information:
A. Date
B. Possible activation of Dualdrive electric power steering
C. Sport driving mode indication (for versions/markets,
where provided)
D. Time
E. Odometer (distance travelled in kilometres/miles)
F. Possible presence of ice on road
G. Outside temperature
H. Scheduled servicing deadline
I. Headlight alignment position (with dipped beam head-
lights on only).
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 20

GETTING TO KNOW YOUR CAR21
1
On some versions the display shows the turbine pressure
fig. 5 when the “engine info ” menu item is selected and
the key is turned to MAR.
fig. 4L0E1000g
fig. 5L0E0004mfig. 6L0E1001g
RECONFIGURABLE MULTIFUNCTIONAL
DISPLAY “STANDARD” SCREEN fig. 6
The standard screen shows the following information:
A. Time
B. Date
C. Sport driving mode indication (for versions/markets,
where provided)
D. Odometer (distance travelled in kilometres/miles)
E. Car status (e.g. doors open, ice on road, etc.)
F. Headlight alignment position (with dipped beam head-
lights on only).
G. Outside temperature
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 21

22GETTING TO KNOW YOUR CAR
fig. 7L0E0005m
CONTROL BUTTONS Fig. 7
Õ: to scroll up through the displayed menu and the re-
lated options or to increase the displayed value.
SET: press briefly to access the menu and/or go to next
screen or confirm the required menu option. Hold down
to go back to the standard screen.
Ô: to scroll down through the displayed menu and the re-
lated options or to decrease the value displayed.IMPORTANT Buttons
ÕandÔactivate different func-
tions according to the following situations:
– within the menu, they allow you to scroll up and down
through the options;
- when carrying out settings they allow you to increase
or decrease values.
IMPORTANT When one of the front doors is opened, the
display will turn on and show the clock and km or mi cov-
ered for a few seconds.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 22

24GETTING TO KNOW YOUR CAR
Selecting an option from the main menu
without submenu:
– briefly press the SET button to select the main menu op-
tion to be set.
– Press button
ÕorÔ(by single presses) to select a new
setting;
– briefly press the SET button to store the new setting and
to go back to the main menu option selected previously.
Selecting an option from the main menu with
submenu:
– briefly press the SET button to display the first submenu
option;
– press button
ÕorÔ(by single presses) to scroll through
all the submenu options;
– briefly press the SET button to select the displayed sub-
menu option and to open the relevant set-up menu;
– press
ÕorÔ(by single presses) to select a new setting
for this submenu option;
– briefly press the SET button to store the new setting and
to go back to the previously selected submenu option.
MENU ITEMS
Lighting (Adjusting lighting
inside the car)
This function may be used to set the brightness of the in-
strument panel, sound system controls and automatic cli-
mate control system controls (for versions/markets, where
provided) to 8 levels.
Proceed as follows to adjust the brightness:
– briefly press SET. The previously set level will flash on
the display;
– press
ÕorÔto set the required brightness level;
– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
Speed beep (Speed limit)
This function may be used to set the car speed limit (km/h
or mph); when this limit is exceeded the driver is imme-
diately alerted (see “Instrument panel warning lights” in
chapter 1). To set the speed limit, proceed as follows:
– briefly press SET. The display will show a dedicated mes-
sage;
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 24

GETTING TO KNOW YOUR CAR25
1
– press ÕorÔto switch the speed limit function “On” or
“Off”;
– if the function is On, press
ÕorÔto select the required
speed limit and then press SET to confirm.
IMPORTANT The speed may be set in the range from 30
to 200 km/h, or from 20 to 125 mph according to the pre-
viously chosen unit of measurement (see “Setting the unit
of measurement”) described below. The setting will in-
crease/decrease by five units each time button
Õ/Ôis
pressed. Hold down button
Õ/Ôto increase/decrease the
setting rapidly. Complete the setting by briefly pressing
the button when you approach the required setting.
– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
To cancel the setting, proceed as follows:
– briefly press SET: ON flashes on the display;
– press
Ô: Off flashes on the display;– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
Headlight sensor (Automatic headlight/dusk
sensor sensitivity adjustment)
(for versions/markets, where provided)
This function is used to adjust the dusk sensor sensitivi-
ty to three levels (level 1 = minimum, level 2 = medium,
level 3 = maximum); the higher the sensitivity, the lower
the amount of external light needed to switch the head-
lights on.
Proceed as follows to set:
– briefly press SET. The previously set level will flash on
the display;
– press
ÕorÔto change the setting;
– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 25