MAZDA 626 1987 Repair Manual

1 A ON-VEHICLE MAINTENANCE (TIMING BELT)
Spark plug
1. Apply anti-seize compound or molybdenum-based
lubricant to the spark plug threads.
2. Install the spark plugs.
Tightening torque:
15—23 N-m (1.5—2.3 m-kg, 11—17 ft-lb)
79G01C-021
Steps After Installation
Perform the necessary engine adjustment. (Refer to
TUNE-UP PROCEDURE.)
86U01X-029
1A—19

1 A ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
CYLINDER HEAD
Removal
Warning: Release the fuel pressure. (Refer to Section 4.)
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01A-110
1A—20

1 A ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
1. High-tension lead and spark plug
2. Accelerator cable
3. Throttle cable (ATX)
4. Air intake pipe (Fl)
5. Air cleaner assembly (carb.)
6. Fuel hose
7. Fuel pump (carb.)
8. Upper radiator hose
9. Heater hose
10. Brake vacuum hose
11. Canister hose (Fl, Middle East)
12. Three-way solenoid assembly
13. Engine harness connector and ground
14. Secondary air pipe assembly (except
General)
15. EGR pipe (Fl, Unleaded carb.)
16. Exhaust manifold insulator
17. Exhaust pipe
18. Exhaust manifold
19. Gusset plate (Fl)
20. Intake manifold bracket (Fl)
21. Intake manifold assembly
22. Distributor
23. A/C compressor and bracket
24. Upper timing belt cover
25. Timing belt tensioner spring
26. Timing belt
27. Cylinder head cover
28. Cylinder head and gasket 76G01A-031
Removal note
Fuel hose
Warning
a) Cover the hose with a rag because fuel will
spray out when disconnecting.
b) Keep sparks and open flame away from the
fuel area.
Plug the disconnected hoses to avoid fuel leakage.
Timing belt
1. Before removing the timing belt, turn the crankshaft
to align the mating mark of the camshaft pulley with
the front housing timing mark.
Note
For FE engine, align "2" mark.
For F8, F6 engine, align "3" mark.
2. Loosen the timing belt tensioner lock bolt.
3. Shift the tensioner outward as far as possible, then
temporarily tighten it.
1A—21

1 A ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
69G01B-037
76G01A-111
4. Remove the timing belt and secure it out of the way
to prevent damage during removal and installation
of the cylinder head.
Cylinder head bolt
Loosen the cylinder head bolts in two or three steps
in the order shown in the figure.
Disassembly of Cylinder Head
Refer to page 1A—40.
Inspection of Cylinder Head
Refer to page 1A—48.
Assembly of Cylinder Head
Refer to page 1A—73.
76G01A-033
1A—22

ON-VEHICLE MAINTENANCE (CYLINDER HEAD) 1 A
Installation
Install in the reverse order of removal referring to the installation note.
Note a) Position the hose clamp in the original location on the hose.
b) Squeeze the clamp lightly with large pliers to ensure a good fit.
Torque Specifications
19—30
N
m (1.9—3.1 m-kg/' 14—22 ft-lb)
37—63
N m
(3.8—6.4 m-kg 27-46 ft-lb)
37—52 Nm (3.8 27—1
31—46 N-m (3.2—<

1 A ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
Installation note
Cylinder head
1. Thoroughly remove all dirt and oil from the top of
the cylinder block with a rag.
2. Place a new cylinder head gasket in position.
86U01X-035
® (5)
CD
© (8)
3. Set the cylinder head in place.
4. Apply engine oil to the bolt threads and seat faces.
5. Tighten the cylinder head bolts in two or three steps
in the order shown in the figure.
Tightening torque:
80—86 N-m (8.2—8.8 m-kg, 59—64 ft-lb)
86U01X-036
Cylinder head cover
1. Apply silicon sealant to the shaded area shown in
the figure.
2. Install the cylinder head cover.
Tightening torque:
6—8
N
m (60—80 cm-kg, 52—69 in-lb)
86U01X-037
Timing belt
1. Align the mating mark of the camshaft pulley with
the front housing timing mark.
Note
For FE engine, align "2" mark.
For F8, F6 engine, align "3" mark.
2. Install the timing belt. (Refer to TIMING BELT of
ON-VEHICLE MAINTENANCE.)
76G01A-034
1A—24

ON-VEHICLE MAINTENANCE (CYLINDER HEAD) 1 A
76G01A-035
Engine harness connector
Install the engine harness connectors.
Distributor
1. Apply engine oil to the O-ring, and position it on
the distributor.
2. Apply engine oil to the blade or gear.
3. Align the mating marks as shown in the figure
...8-valve.
4. Install the distributor with the marks facing straight
up.
5. Loosely tighten the distributor mounting bolt.
1. IG coil
2. Engine ground
3. Water tempera-
ture sensor
4. Water thermo
switch
5. Oxygen sensor
(Fl)
6. Injection harness
(Fl)
7. F/l solenoid
valve (Fl)
8. Throttle sensor
(Fl)
76G01A-113
Steps After Installation
1. Fill the radiator with the specified amount and type
of coolant.
2. Perform the necessary engine adjustments. (Re-
fer to TUNE-UP PROCEDURE.)

1
A—25

1 A ON-VEHICLE MAINTENANCE (VALVE SEAL)
VALVE SEAL
Removal
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01A-114
11. Fuel hose (carb.)
12. Rear housing
13. Rocker arm and shaft assembly
14. Camshaft cap (12-valve)
15. Camshaft
16. Valve keeper
17. Upper valve spring seat
18. Valve spring
19. Lower valve spring seat
20. Valve seal
1. Air cleaner assembly (carb.)
2. Air intake pipe (Fl)
3. High-tension lead and spark plug
4. Upper timing belt cover
5. Timing belt
6. Cylinder head cover
7. Camshaft pulley
8. Front housing
9. Distributor
10. Upper radiator hose
1A—26

1 A ON-VEHICLE MAINTENANCE (VALVE SEAL)
12-valve
O ® ® ® ©
Removal note
Timing belt
Remove the timing belt. (Refer to page 1A—14.)
Rocker arm and shaft assembly
Loosen the rocker arm shaft bolts in two or three steps
in the order shown in the figure.
76G01A-037
8-valve
CD © CD ® © ® ©
12-valve Valve seal
1. Remove the rocker arms and springs from the
rocker arm shaft.
2. Install the camshaft caps and rocker arm shafts
onto the cylinder head.
3. Plug the oil drain hole with a rag to prevent the pos-
sibility of the valve keepers from falling into the oil
pan.
86U01X-045
1A—27

1 A ON-VEHICLE MAINTENANCE (VALVE SEAL)
4. Turn the crankshaft to position the piston of the
valve seal to be replaced at top dead center.
5. Remove the valve keepers with the SST.
6. Remove the valve spring and spring seats.
86U01X-046
7. Remove the valve seal from the valve guide with
the SST.
Caution
Do not turn the crankshaft while the valve
spring is removed.
Replace the valve seals at every cylinders.
86U01X-047
1A—28