MAZDA MODEL MX-30 EV 2022 Owners Manual

Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
Do not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and gasoline. Otherwise, it may
cause discoloration or stains.
Rubbing hard with a sti
ff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following, wipe it o ff
immediately using a soft cloth.
Leaving it uncleaned could cause
discoloration, stains, cracks, or peeling
of the coating , and it will make it hard
to wipe o ff later.
Beverage or fragranceGrease or oilSoiling
▼ Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe o ff the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which have been pulled out for cleaning,
dry them o ff thoroughly and make
sure there is no remaining moisture
on them.
WARNING
If a seat belt appears frayed or has
abrasions, have it replaced by an
Authorized Mazda Dealer:
If a seat belt is used under such a
condition, it cannot function at its full
capacity which could result in serious
injury or death.
Use a mild detergent to remove
soiling from a seat belt:
If organic solvents are used for cleaning
the seat belts or they become stained
or bleached, there is the possibility of
them becoming weakened and as a
result, they may not function at their
full capacity which could cause serious
injury or death.
NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will
make it
difficult to clean them later,
and it may a ffect the smooth retracting
of the seat belt.
▼ Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
▼Upholstery and Synthetic Leather
Maintenance
Fabric
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
Maintenance and Care
Appearance Care
6-40
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
Synthetic leather
1. Remove dust and sand using a vacuum cleaner.
2. Wipe the soiled area with a soft cloth soaked in a mild detergent
(approx. 5%) diluted with water.
3. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
▼ Leather Upholstery Maintenance*
1. Remove dust and sand using a
vacuum cleaner.
2. Wipe off the soiled area with a soft
cloth and a suitable, special cleaner
or a soft cloth soaked in a mild
detergent (about 5%) diluted with
water.
3. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
4. Remove moisture with a dry, soft cloth and allow the leather to
further dry in a well-ventilated,
shaded area. If the leather gets wet
such as from rain, remove the
moisture and dry it as soon as
possible.
NOTE
Because genuine leather is a natural
material, its surface is not uniform
and it may have natural scars,
scratches, and wrinkles.
To maintain the quality for as long as
possible, periodical maintenance,
about twice a year, is recommended.
If the leather upholstery comes into
contact with any of the following,
clean it immediately.
Leaving it uncleaned could cause
premature wear, mold, or stains.
Sand or dirtGrease or oil, such as hand creamAlcohol, such as in cosmetic or
hair dressing items
If the leather upholstery gets wet,
promptly remove moisture with a dry
cloth. Remaining moisture on the
surface may cause deterioration such
as hardening and shrinkage.
Exposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car
under direct sunlight for long
periods, shade the interior using
sunshades.
Do not leave vinyl products on the
leather upholstery for long periods.
They may a ffect the leather quality
and coloring. If the cabin
temperature becomes hot, the vinyl
may deteriorate and adhere to the
genuine leather.
▼ Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discoloration, stains,
cracks or peeling of the coating.
▼
Instrument Panel Top (Soft pad)
Maintenance
Extremely soft materi
al is used for the
soft pad surface. If the soft pad surface
is rubbed harshly with a dry cloth, it
could result in the surface being
damaged and leaving white scratch
marks.
1. Wipe the soiled area with a soft cloth soaked in a mild detergent
(approx. 5%) diluted with water.
2. Wipe o ff the remaining detergent
using a cloth soaked in clean water
and wrung out well.
Maintenance and Care
Appearance Care
*Some models.6-41
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Active Driving Display
Maintenance
The dust-proof sheet has a coating.
When cleaning , do
not use a hard or
rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving
display, wipe it o ff immediately. The
dust-proof sheet could be damaged
and the surface coating could be
scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning
the dust-proof sheet is recommended.
▼ Panel and Cork Area Maintenance
If a panel or cork area becomes soiled,
gently wipe it o
ff with a soft cloth
soaked in clean water and thoroughly
wrung out.
If some areas require further cleaning ,
use the following procedure:
1. Wipe the soiled area with a soft cloth soaked in a mild detergent
(approx. 5 %) diluted with water.
2. Wipe o ff the remaining detergent
using a cloth soaked in clean water
and wrung out well.
NOTE
Be particularly careful when cleaning
shiny surface panels and metallic
parts such as plating as they can be
scratched easily.
(Cork area)
Do not apply items with adhesive
properties to the cork area.
Otherwise, the cork could be
damaged.
▼ Glass and Mirror Maintenance
Use Mazda genuine glass cleaner to
remove oil
film from the glass or
mirror.
When cleaning the interior side of the
window glass, gently wipe it with a soft
cloth soaked in clean water and
thoroughly wrung out.
If there is oil film on the windshield,
headlight beams from on-coming
vehicles may re flect irregularly
especially on a rainy night, and your
front vision might be obstructed.
If an antenna or filament is printed on
the window glass, gently wipe along
the antenna or filament to clean that
area.
CAUTION
If some areas require further cleaning,
a glass cleaning agent can be used.
However, be careful of the following
points.
 Follow the instructions on the glass
cleaner container.
 Do not use a glass cleaning agent on
a window antenna and filaments,
and on a rearview mirror equipped
with the automatic glare prevention
function.
Using a glass cleaning agent may
damage the window antenna or
fi laments, and the automatic glare
prevention function may not operate
normally.
▼ Cleaning the Floor Mats
Rubber
floor mats should be cleaned
with mild soap and water only.
WARNING
Do not use rubber cleaners, such as
tire cleaner or tire shine, when
cleaning rubber floor mats:
Cleaning the rubber floor mats with
rubber cleaning products makes the
fl oor mats slippery.
Maintenance and Care
Appearance Care
6-42
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

This may cause an accident when
depressing the accelerator or brake
pedal or when getting in or out of the
vehicle.
After removing the floor mats for
cleaning, always reinstall them securely
(page 3-57).
Maintenance and Care
Appearance Care
6-43
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

MEMO
6-44
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

7If Trouble Arises
Helpful information on what to do if a problem arises with the
vehicle.
Parking in an Emergency............ 7-2 Parking in an Emergency......... 7-2
Flat Tire................................... 7-3 Tool Storage.......................... 7-3
Emergency Flat Tire Repair
Kit........................................ 7-4
Changing a Flat Tire..............7-10
Troubleshooting for Charging ..........
............................................ 7-11 What to do when charging is not
possible.............................. 7-11
Depleted Lead-acid Battery...... 7-12 Jump-Starting...................... 7-12
Fully Discharged High Voltage
Battery...................................7-16 Fully Discharged High Voltage
Battery................................ 7-16
Emergency Starting................. 7-17 Push-Starting....................... 7-17
Emergency Towing.................. 7-18 Towing Description.............. 7-18
Tiedown Hooks*.................. 7-19
Warning/Indicator Lights and
Warning Sounds..................... 7-21 If a Warning Light Turns On or
Flashes................................ 7-21
Message Indicated on Multi-
information Display............. 7-33
Warning Sound is
Activated.............................7-37
When Liftgate Cannot be
Opened................................. 7-42 When Liftgate Cannot be
Opened.............................. 7-42
Active Driving Display Does Not
Operate................................. 7-43 If the Active Driving Display Does
Not Operate........................ 7-43
Windshield Wipers Operate at High
Speed.................................... 7-44 Windshield Wipers Operate at
High Speed......................... 7-44
*Some models.7-1
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Parking in an Emergency
▼Parking in an Emergency
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a
traffic
hazard and that they must take
extreme caution when near it.

Depress the hazard warning flasher
and all the turn signals will flash. The
hazard warning indicator lights in the
instrument cluster flash simultaneously.
NOTE
The turn signals do not work when
the hazard warning lights are on.
Check local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
If Trouble Arises
Parking in an Emergency
7-2
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

To o l S t o ra g e
▼Tool Storage
NOTE
Your vehicle may or may not be
equipped with a spare tire. For details,
consult an Authorized Mazda Dealer.
Tools are stored in the locations
illustrated in the diagram.
Ty p e A
1. Emergency
flat tire repair kit
2. Tiedown eyelet
3. Jack lever
Ty p e B
1. Emergency flat tire repair kit
2. Tiedown eyelet
3. Jack lever
▼ Jack
NOTE
A jack is not equipped in the vehicle as
standard equipment. When replacing
the tire, use a jack. Consult an
Authorized Mazda Dealer for details.
Designated jack-up position
1. Jacking position
If Trouble Arises
Flat Tire
7-3
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Emergency Flat TireRepair Kit
▼Emergency Flat Tire Repair Kit
The emergency
flat tire repair kit
included with your Mazda is for a
temporary repair of a slightly damaged
fl at tire resulting from running over
nails or similar sharp objects on the
road surface.
Perform the emergency flat tire repair
without removing the nail or similar
sharp object which punctured the tire.
NOTE
Your vehicle is not equipped with a
spare tire. In the event of a flat tire, use
the emergency flat tire repair kit to
repair the tire temporarily. When doing
the repair, refer to the instructions
included in the emergency flat tire
repair kit. If an emergency repair was
performed on a flat tire using the
emergency flat tire repair kit, have an
Authorized Mazda Dealer, repair or
replace the tire as soon as possible.
▼ About the Emergency Flat Tire
Repair Kit
The emergency fl
at tire repair kit
includes the following items.

1. Sealant bottle
2. Compressor
3. Speed restriction sticker
4. Repaired tire sticker
5. Instructions
WARNING
Do not allow children to touch the
tire sealant:
 Ingestion of tire sealant is dangerous.
In the event tire sealant is
accidentally swallowed, drink large
amounts of water immediately and
seek medical assistance.
 Tire sealant that comes into contact
with the eyes and skin is dangerous.
If tire sealant enters the eyes or
contacts the skin, flush immediately
with large amounts of water and
seek medical assistance.
If Trouble Arises
Flat Tire
7-4
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

NOTE
The tire sealant cannot be reused.
Purchase new tire sealant at an
Authorized Mazda Dealer.
The emergency flat tire repair kit
cannot be used in the following
cases.
Consult an Authorized Mazda
Dealer.
The period of eff ective use for the
tire sealant has expired. (The
period of eff ectiveness is indicated
on the bottle label.)
The tear or puncture exceeds
about 4 mm (0.16 in).
The damage has occurred to an
area of the tire other than the
tread.
The vehicle has been driven with
nearly no air remaining in the tire.
The tire has come o ff the wheel
rim.
Damage to the wheel rim has
occurred.
The tire has 2 or more punctures.
▼ Using the Emergency Flat Tire
Repair Kit
1. Park on a level surface o
ff the
right-of-way and set the parking
brake.
2. Shift the selector lever to the P position and switch the power
switch to OFF.
3. Turn on the hazard warning flasher.
4. Unload passengers and luggage,
and remove the emergency flat tire
repair kit.

5. Shake the sealant bottle to mix the contents. Then extend the injection
hose.

1. Injection hose
CAUTION
Do not shake the bottle excessively.
Otherwise, the sealant could spray
out of the injection hose, and if the
sealant contacts clothing or other
objects, you may not be able to
remove it.
NOTE
The sealant hardens easily and
injecting it will be di fficult under
cold weather conditions (0 °C
(32 °F) or below). Warm the
sealant inside the vehicle to
facilitate injection.
If Trouble Arises
Flat Tire
7-5
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07