clock NISSAN NOTE 2016 Service Repair Manual

AV-14
< SYSTEM DESCRIPTION >[BASE AUDIO]
DIAGNOSIS SYSTEM (AUDIO UNIT)
DIAGNOSIS SYSTEM (AUDIO UNIT)
Diagnosis DescriptionINFOID:0000000012432871
The audio unit on board diagnosis performs the functions listed in the table below:
On Board Diagn
osis FunctionINFOID:0000000012432872
METHOD OF STARTING
Hardware/Software Versions and Speaker Channel Check
1. Turn the ignition ON.
2. Turn the audio system OFF.
3. While pressing the preset 1 butt on, turn the volume control dial
clockwise or counterclockwise 30 clicks or more.
4. Initially, all display segments will be illuminated.
5. To exit hardware/software versions and speaker channel check, turn the ignition OFF.
Communication Diagnosis
1. Turn the ignition ON.
2. Turn the audio system OFF.
Mode Description
Hardware/Software Versions The following information is available for the audio unit:
• hardware version.
• software version.
• EQ pin info.
Speaker Channel Check The connection of the speakers to the audio unit can be confirmed.
Communication Diagnosis The AV communication (M-CAN) message history can be monitored.
AWNIA3042ZZ
ALNIA1382GB
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
DIAGNOSIS SYSTEM (AUDIO UNIT)AV-15
< SYSTEM DESCRIPTION > [BASE AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
3. While pressing the preset 6 button, turn the volume control dial clockwise or counterclockwise 30 clicks or more.
4. Initially, the communication diagnosis mode is displayed.
5. To exit communication diagnosis, turn the ignition OFF.
SELF DIAGNOSIS MODE
Hardware/Software Versions
1. Press the DISP button to enter versions display, and the audio head unit software version is displayed.
2. With each additional press of the DISP button, the following information is available:
- HARD V###### (hardware version)
- EEP V###### (EEPROM version)
- @@@@ EQ1-4 # (EQ pin info) If an EQ error is present, INVALID EQ is displayed
3. Hold the DISP button down to return to all display segments screen.
Speaker Channel Check
ALNIA1516ZZ
ALNIA1387GB
ALNIA1383GB
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
DIAGNOSIS SYSTEM (AUDIO UNIT)AV-71
< SYSTEM DESCRIPTION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
DIAGNOSIS SYSTEM (AUDIO UNIT)
DescriptionINFOID:0000000012432960
The audio unit on board diagnosis performs the functions listed in the table below:
On Board Diagnosis FunctionINFOID:0000000012432961
METHOD OF STARTING
1. Turn the ignition ON.
2. Turn the audio unit OFF.
3. While pressing the preset 1 button, turn the volume control dial clockwise and counterclockwise quickly approximately 15 times
or more. Shifting from current screen to previous screen is per-
formed by pressing BACK button.
4. The trouble diagnosis initial screen is displayed, and Self Diag- nosis or Confirmation/Adjustment can be selected.
SELF DIAGNOSIS MODE
Audio Unit Self Diagnosis
1. Select Self Diagnosis.
Mode Description
Self Diagnosis Audio unit diagnosis.
Confirmation/ Adjustment Display Diagnosis
The following check functions are available: color tone check by color
spectrum bar display and gray scale check by gradation bar display.
Vehicle Signals Diagnosis of signals can be performed for vehicle speed, lights, reverse,
EQ pin, ignition, destination and camera type.
Speaker Test The connection of a speaker can be confirmed by test tone.
Error History The system malfunction and the frequency when occurring in the past are
displayed. When the malfunctioning item is selected, the time and place
that the selected malfunction last occurred are displayed.
Camera System Guiding line position that overlaps rear view camera image can be adjust-
ed.
AV COMM Diagnosis Displayed but not used.
Delete Unit Connection Log Erase the connection history of unit and error history.
Version Information Displays the audio system version information.
Initialize Setting Initializes the audio unit memory.
ALNIA1710ZZ
JSNIA0138GB
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-144
< SYSTEM DESCRIPTION >[NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
3. While pressing the APPS button, turn the TUNE dial counter-
clockwise 5 or more clicks, then clockwise 5 or more clicks, then
counterclockwise 5 or more clicks. Shifting from current screen
to previous screen is performed by pressing BACK button.
4. The trouble diagnosis initial screen is displayed, and Version, User Configuration, Radio, Syst em State or Self Test can be
selected.
CONSULT FunctionINFOID:0000000012433016
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the AV control unit.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
Refer to AV-151, "DTC Index".
DATA MONITOR
CONFIGURATION
Refer to AV-175, "CONFIGURATION (AV CONTROL UNIT) : Description".
CAN DIAG SUPPORT MNTR
AWNIA3744ZZ
AWNIA3745ZZ
Direct Diagnostic Mode Description
ECU Identification The AV control unit part number is displayed.
Self Diagnostic Result The AV control unit self diagnostic results are displayed.
Data Monitor The AV control unit input/output data is displayed in real time.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing AV control unit.
CAN Diag Support Mntr • The result of transmit/receive diagnosis of AV communication is displayed.
• The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item [Unit]
Description
VHCL SPD SIG [On/Off] Indicates vehicle speed signal received from combination meter on CAN communication
line.
ILLUM SIG [On/Off] Indicates condition of illumination signal for the AV control unit.
IGN SIG [On/Off] Indicates condition of ignition signal.
REV SIG [On/Off] Indicates condition of reverse signal received from transmission range switch (with CVT)
or park/neutral position (PNP) switch (back-up) (with M/T).
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
BCM
BCS-37
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N19
(LG) Ground
Keyless tuner power
supply OutputPush-button ignition switch OFF
Push-button ignition switch ACC or ON
5 V
20
(G) Ground Keyless tuner signal Input Push-button ig-
nition switch
OFFWaiting
When operating either
button on Intelligent Key
21
(P) Ground Immobilizer one way
communication
(CLOCK) signal Input/
Output Intelligent Key
battery is re-
moved Brake pedal depressed
NOTE:
Waveform varies each
time when brake pedal is
depressed
Brake pedal released
Battery voltage
22
(W) Ground Keyless tuner RSSI
signal
InputPush-button ig-
nition switch
OFF Waiting
When pressing and hold-
ing either button on Intelli-
gent Key
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JMKIA3838GB
JMKIA3838GB
JMKIA3841GB
JMKIA6232JP
JMKIA5952GB
JMKIA5953GB
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
COMBINATION SWITCHBCS-75
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
Removal and InstallationINFOID:0000000012432359
CAUTION:
• Before servicing, turn the ignition
switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air or electric tools when remo ving or installing the combination switch.
REMOVAL
1. Disconnect the negative and positive bat tery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
2. Remove the steering column covers. Refer to IP-17, "
Removal and Installation".
3. Rotate steering wheel clockwise to access first combination switch screw (A) and remove.
4. Rotate steering wheel counter-clockwise to access second com- bination switch screw (A) and remove.
5. Disconnect the harness connector (B) from the combination switch (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag wa rning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to BCS-58, "
Description".
ALMIA0648ZZ
ALMIA0649ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-108
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
20
(G) Ground Keyless tuner signal Input Ignition switch
OFFKey inserted into ignition
key cylinder
0 V
Waiting
Signal receiving
21
(P) Ground Immobilizer one way
communication
(clock) signal Input/
Output While waiting Turn ignition switch ON.
Turn ignition switch ON: Pointer
of tester should move.
23
(GR) Ground Security indicator
output signal
InputSecurity indica-
tor ON
0 V
Blinking (Ignition switch
OFF) 11.3 V
OFF Battery voltage
24
(SB) Ground Audio/dongle link
(serial) signal Input/
Output Ignition switch OFF.
5 V
25
(LG) Ground Immobilizer two way
communication sig-
nal Input/
Output While waiting Turn ignition switch ON. Turn ignition switch ON: Pointer
of tester should move.
26
(O) Ground
THERMO amp. sig-
nal InputPush-button ig-
nition switch ON
and blower fan
switch ON A/C switch OFF
Battery voltage
A/C switch ON 0 V
27
(V) Ground
Air conditioner
switch signal Input A/C switch OFF
Battery voltage
ON 0 V
28
(SB) Ground Blower fan sw signal Input Fan switch OFF
0 V
I, II, III or IIII 7.0 - 8.0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PIIB7728J
PIIB7729J
JPMIA0014GB
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-138
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
COMBINATION SWITCH
COMBINATION SWITCH
Removal and InstallationINFOID:0000000012432412
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air or electric tools when remo ving or installing the combination switch.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
2. Remove the steering column covers. Refer to IP-17, "
Removal and Installation".
3. Rotate steering wheel clockwise to access first combination switch screw (A) and remove.
4. Rotate steering wheel counter-c lockwise to access second com-
bination switch screw (A) and remove.
5. Disconnect the harness connector (B) from the combination switch (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag wa rning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to BCS-121, "
Description".
ALMIA0648ZZ
ALMIA0649ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CL-6
< PERIODIC MAINTENANCE >
CLUTCH PEDAL
Check that the clearance (C) between the thread end of clutch inter-
lock switch (1) and stopper rubber (2) is within the specification
range while clutch pedal is fully depressed.
Position of Clutch Pedal Position Switch (if equipped)
Check that the clearance (A) between the thread end of clutch pedal
position switch (1) and clutch pedal (2) is within the specification
range while clutch pedal is fully released.
ADJUSTMENT
Position of Clutch Interlock Switch
1. Disconnect the harness connector from the clutch interlock switch.
2. Rotate the clutch interlock switch (1) 45 degrees counterclock- wise to release from bracket.
3. With the clutch pedal fully depressed, insert the clutch interlock switch (1) until it contacts the stopper rubber (2).
4. Rotate the clutch interlock switch 45 degrees clockwise to set clearance (A) between the clutch interlock switch (1) and stop-
per rubber (2).
CAUTION:
The clearance (C) must be wi thin the specification range.
NOTE:
Fully depressed clutch pedal means a clutch pedal condi tion that the clutch pedal lever contacts the pedal
stopper rubber.
Position of Clutch Pedal Position Switch (if equipped)
1. Disconnect the harness connector from the clutch pedal position switch.
2. Rotate the clutch pedal position switch 45 degrees counterclock- wise to release from bracket.
3. Insert the clutch pedal position switch (1) until it contacts the
clutch pedal (2).
4. Rotate the clutch pedal position switch 45 degrees clockwise to set clearance (A) between the clutch pedal position switch (1)
and clutch pedal (2).Clearance (C) : Refer to
CL-22, "
Clutch Pedal".
JPDIB0164ZZ
Clearance (A) : Refer to CL-22, "Clutch Pedal".
JPDIB0165ZZ
Clearance (C) : Refer to CL-22, "Clutch Pedal".JPDIB0164ZZ
Clearance (A) : Refer to CL-22, "Clutch Pedal".
JPDIB0165ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CLUTCH PEDALCL-11
< REMOVAL AND INSTALLATION >
CEF
G H
I
J
K L
M A
B
CL
N
O P
REMOVAL AND INSTALLATION
CLUTCH PEDAL
Exploded ViewINFOID:0000000012432220
Removal and InstallationINFOID:0000000012432221
REMOVAL
1. Remove the instrument lower panel LH. Refer to IP-24, "Removal and Installation".
2. Disconnect master cylinder rod end ( ) from clutch pedal.
3. Disconnect the harness connector from the clutch interlock switch.
4. Disconnect the harness connector from the clutch pedal position switch (if equipped).
5. Remove harness clips from clutch pedal.
6. Remove clutch pedal nuts and remove clutch pedal.
7. Remove pedal pad from clutch pedal.
8. Rotate the clutch interlock switch 45 degrees counterclockwise to release from bracket.
9. Rotate the clutch pedal position switch 45 degrees c ounterclockwise to release from bracket (if equipped).
10. Remove pedal stopper rubber from clutch pedal using a suitable tool.
1. Clutch pedal 2. Pedal stopper rubber3. Pedal pad
4. Clutch interlock switch 5. Clip6. Clutch pedal position switch (if
equipped)
7. Clip Front
ALBIA1141ZZ
PCIB1491E
Revision: August 2015 2016 Versa Note

cardiagn.com