SSANGYONG MUSSO 1998 Workshop Repair Manual

OM600 ENGINE MECHANICAL 1B3-49
41. Remove the bolt(32).
42. Separate the spring and pull out the tensioning lever(31).
43. Pry off the closing cover. Remove the bolt and then remove
the idle pulley.
44. Using the sliding hammer(36) and the threaded pin(37),
pull out the sliding rail pins(25, 26) and remove the sliding
rail(24).
Sliding Hammer 116 589 20 33 00
Threaded Pin 116 589 02 34 00

1B3-50 OM600 ENGINE MECHANICAL
OM 662LA
46. Disconnect the vacuum pipe from thermo valve.
47. Remove the socket bolts(13) of the chain box.
T Type Socket Wrench 116 589 03 07 00
Magnetic Bar 102 589 03 40 00
48. Remove the cylinder head bolts in numerical se-quence.
Cylinder Head Bolt Wrench 601 589 00 10 00
45. Remove the vacuum line from the vacuum pump.

OM600 ENGINE MECHANICAL 1B3-51
49. Remove the cylinder head(2) and gasket(3).
OM 661LA

1B3-52 OM600 ENGINE MECHANICAL
Length(L)
Assembly Procedure
1. Replace the cylinder head gasket.
2. Install the cylinder head onto the crankcase.
Notice
Align the cylinder head holes with the guide pins.
3. Measure the length(L) of cylinder head bolts.
Notice
If the max. length is exceeded, replace the bolts.
Thread Dia. Max. Limit(L)
M10
M10
M1080mm
102mm
115mm82mm
104mm
117mm when new
4. Coat the head contact surface of bolts and thread with oil
and insert them as shown.
- Cylinder head bolts arrangement
Bore
1 ...........................................M10
× 80
2 ...........................................M10
× 102
3 ...........................................M10
× 11 5
4 ........................................... M 8
× 50
5 ........................................... M 8
× 80
OM662LA

OM600 ENGINE MECHANICAL 1B3-53
5. Tighten the cylinder head bolts to specified torque and
torque angle.
OM 662LA
OM 661LA
6. Install the socket bolts in the chain box.
Tightening Torque 25 Nm
Stage 1
Stage 2
Torque angle
Wait for
Torque angle15 Nm
35 Nm
90°
10 minutes
90°
7. Connect the vacuum pipe to the thermo valve.

1B3-54 OM600 ENGINE MECHANICAL
8. Connect the vacuum lines to the vacuum pump.
9. Install the fuel filter and connect the pipe.
Tightening Torque 25 Nm
Notice
Be careful not to be confused the connections and hoses.
10. Connect the fuel pipe to the injection pump.
11. Install the sliding rail(24) and insert the sliding rail pins(25,
26).
Notice
Apply sealing compound on the each collar of the sliding
rail pins.
Sliding Hammer 116 589 20 33 00
Threaded Pin 116 589 02 34 00

OM600 ENGINE MECHANICAL 1B3-55
12. Install the idle pulley and fit the closing cover.
Tightening Torque 25 Nm
13. Insert the tensioning lever(31) and install the spring.
14. Install the damper.
Tightening Torque 23 Nm
Notice
Insert the tensioning lever bolts onto the mounting hole.
15. Insert the locking washer.
16. Inspect the valve tappet and check that the tappet moves
smoothly.

1B3-56 OM600 ENGINE MECHANICAL
17. Coat the camshaft with oil and install the camshaft on the
cylinder head to be TDC mark(arrow) upward.
18. Measure the axial end play of the camshaft.
End Play 0.06 - 0.21mm
Notice
If out of standard, adjust it with the proper thickness of
locking washer.
19. Install the bearing caps on the camshaft according to the
number on the caps.
20. Tighten the bearing cap bolts according to the numerical
sequence.
Tightening Torque 25 Nm
Notice
Tighten the No. 1 bolts(light arrow) first and then tighten
the No. 2 bolts(dark arrow) stage by stage.
OM662LA
OM661LA

OM600 ENGINE MECHANICAL 1B3-57
21. Position the camshaft on marking and install the camshaft
sprocket.
Notice
Align the alignment marks on the chain and sprocket.
23. Install the camshaft sprocket bolt. 22. Check the TDC position of the crankshaft.
Tightening Torque 25 Nm + 90°

1B3-58 OM600 ENGINE MECHANICAL
24. Install the exhaust manifold and gasket.
25. Install the turbocharger.
26. Install the exhaust pipe onto the turbocharger.
Tightening Torque 25 Nm
Notice
Measure the max. length ‘L’ and replace the bolt if it exceeds
53.6mm.